RISCO Group RWT74 - Manual

Wireless Twin Beam
Model: RWT74
Assembly & Installation Instructions
© RISCO Group 03/2012 5IN1526 B
Tx Rail Rx Rail
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials
and workmanship under normal use for 24 months from the date of production. Because Seller does not install or
connect the product and because the product may be used in conjunction with products not manufactured by the
Seller, Seller cannot guarantee the performance of the security system which uses this product. Seller's obligation
and liability under this warranty is expressly limited to repairing and replacing, at Seller's option, within a
reasonable time after the date of delivery, any product not meeting the specifications. Seller makes no other
warranty, expressed or implied, and makes no warranty of merchantability or of fitness for any particular purpose.
In no case shall seller be liable for any consequential or incidental damages for breach of this or any other
warranty, expressed or implied, or upon any other basis of liability whatsoever.
Seller's obligation under this warranty shall not include any transportation charges or costs of installation or any
liability for direct, indirect, or consequential damages or delay.
Seller does not represent that its product may not be compromised or circumvented; that the product will prevent
any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases
provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may
only reduce the risk of burglary, robbery or fire without warning, but is not insurance or a guaranty that such event
will not occur or that there will be no personal injury or property loss as a result thereof.
Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that
the product fails to give warning. However, if seller is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, seller's maximum liability
shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against seller.
No employee or representative of Seller is authorized to change this warranty in any way or grant any other
warranty.
WARNING: This product should be tested at least once a week.
All rights reserved. No part of this document may be reproduced in
any form without prior written permission from the publisher.
RTTE Compliance Statement
Risco Ltd. hereby declares that this equipment is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.
UK Tel: +44-(0)-161-655-5500
E-mail: [email protected]
ITALY Tel: +39-02-66590054
E-mail: [email protected]
SPAIN Tel: +34-91-490-2133
E-mail: [email protected]
FRANCE Tel: +33-164-73-28-50
E-mail: [email protected]
BELGIUM Tel: +32-2522-7622
E-mail: [email protected]
U.S.A Tel: +1-631-719-4400
E-mail: [email protected]
RISCO Group Contacting Info
RISCO Group is committed to customer service and product support. You can contact
us through our website (www.riscogroup.com) or at the following telephone and fax
numbers:
FCC Note:
Only the 433,92 MHz version is FCC approved and to be sold in US.
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment
BRAZIL Tel: +55-11-3661-8767
E-mail: [email protected]
CHINA (Shanghai) Tel: +86-21-52-39-0066
E-mail: [email protected]
CHINA (Shenzhen) Tel: +86-755-82789285
E-mail: [email protected]
POLAND Tel: +48-22-500-28-40
E-mail: [email protected]
ISRAEL Tel: +972-3-963-7777
E-mail: [email protected]
x4
A D E
x2
F
+
Place the Rx unit into one aluminum rail and the Tx unit into the second rail.
Important: 1. Pay attention to the units direction as indicated in the
drawings (Fig.A).
2. Pay attention that the units are correctly placed on the sliding
track (Fig.B).
x1 x2 x2
C B
x1
A C
B
1 2
4
3
4
2
5
5
1
A. Rail holder
B. IR filter cover
C. Aluminum rail
D. Tx
E. Rx
F. Battery
G. Screw
H. Dibble
1. Antenna
2. Buzzer
3. Alarm LED
4. PCB Spring locker
5. IR Lens
6. Battery compartment
G H
x4 x4
12 34
ON
R C
+
I
TC
I
+
Press the PCB Spring Lockers on the Rx and Tx units
and slide them towards the rail holders to the end of
the rail.
6 6
12 34 ON
R C
+
I
TC
I
+
A
B
1. Separate the IR filter cover from the aluminum rail.
2. Place the rail holders on the top and bottom of both the Rx and Tx
aluminum rails as follows:
A. Take the rail holder and remove the cover (Fig.A)
B. Remove the swivel cover (Fig.B)
C. Slide the rail holder into the aluminum rail (Fig.C)
3