Sharp PN-V602 - Manual (Page 55)

55
E
Specifications
n PN-V602 Product Specifications
Model PN-V602
LCD component 60" Class [60 inch (152.4cm) diagonal] TFT LCD
Max. resolution (pixels) 1366 x 768
Max. colors Approx. 16.77 M colors
Pixel pitch 0.973 mm (H) × 0.973 mm (V)
Viewing angle 176° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm) 52-5/8 x 29-7/16 (1328.8 x 747.1)
Computer input signal Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Sync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play VESA DDC2B
Power management VESA DPMS, DVI DMPM
Input terminals PC/AV Digital HDMI x 1
PC Analog Mini D-sub 15 pin, 3 rows x 1
Audio 3.5 mm mini stereo jack x 1
Serial (RS-232C) D-sub 9 pin x 1
When PN-ZB02
(optional) is
attached
PC/AV Digital DVI-D 24 pin (HDCP compatible) x 1
PC Analog BNC * 1 * 2 x 1
AV Composite video BNC x 1
S-video x 1
Component BNC (Y, Cb/Pb, Cr/Pr) * 1 x 1
Audio RCA pin (L/R) x 2
Output terminals Audio RCA pin (L/R) x 1
Serial (RS-232C) D-sub 9 pin x 1
When PN-ZB02
(optional) is
attached
PC/AV Digital DVI-D 24 pin x 1
External speaker 10 W + 10 W [6 Ω]
LAN terminal
[ When PN-ZB02 (optional) is attached]
10 BASE-T/100 BASE-TX
Power requirement AC 100 V - 240 V, 50/60 Hz
Operating temperature * 3 32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(maximum / input signal waiting mode * 4 / standby
mode * 5 )
510 W / 1.0 W / 1.0 W
Power consumption [PN-ZB02 (optional)] 530 W
Dimensions (excluding protrusions) inch (mm) Approx. 52-5/8 (W) x 5-7/8 (D) x 29-11/16 (H) (1335.9 x 149.3 x 754.2)
Weight lbs. (kg)
Weight [PN-ZB02 (optional)] lbs. (kg)
Approx. 97.0 (44)
Approx. 1.102 (0.5)
*1 Cannot be used simultaneously.
*2 Does not support plug and play.
*3 Temperature condition may change when using the display together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
*4 When AUTO INPUT CHANGE is set to OFF.
*5 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
n PN-ZR01 (optional) Product Specifications
Model PN-ZR01
Remote control sensor box dimensions inch (mm) Approx. 1-3/8 (W) x 7/8 (D) x 5-1/8 (H) (34.2 x 23 x 130)
Remote control sensor box weight lbs. (kg) Approx. 0.220 (0.1)