Honeywell CJ 110MVA - Manual (Page 18)

18
English
No. 1
No. 1
No. 11
No. 12
No. 15
No. 16
No. 21
No. 22
No. 41
No. 97
(Long)
(Super Long)
Thickness of material: inch (mm)
Below
Below
3/8
–
2-5/32
Below
3/8
–
2-5/32
3/16
–
1-9/16
3/8
–
2-9/16
4-1/8 (105)
5-5/16 (135)
(10 – 55)
3/4(20)
(10
–
55)
(5
–
40)
(10
–
65)
3/16
–
1-3/16
Below
3/16
–
1-3/16
1/8
–
3/4
(5
–
30)
3/8 (10)
(5
–
30)
(3
–
20)
1/8
–
15/64
Below
5
/64
–
3/16
(3
–
6)
1/8(3)
(2
–
5)
1/16
–
5/32
(1.5
–
2.5)
1/8
–
15/32
Below
Below
(3
–
12)
1/8(3)
3/16(5)
Height
Height
up to
up to
63/64(25
)
63/64(25)
3/16
–
3/4
Below
3/16
–
19/32
Below
3/16
–
19/32
(5
–
20)
1/4(6)
(5
–
15)
1/4(6)
(5
–
15)
3/16–1-3/16
Below
3/16
–
3/4
Below
3/16
–
1-3/16
1/8
–
3/4
3/16
–
19/32
(5
–
30)
3/8(10)
(5
–
20)
3/16(5)
(5
–
30)
(3
–
20)
(5
–
15)
3/8
–
2-5/32
1/8
–
63/64
3/16
–
63/64
1/8
–
63/64
3/8
–
2-5/32
1/8
–
1-1/2
3/16
–
63/64
(10
–
55)
(3
–
25)
(5
–
25)
(3
–
25)
(10
–
55)
(3
–
40)
(5
–
25)
3/8
–
2-5/32
1/8
–
63/64
3/8
–
2-5/32
1/8
–
1-1/2
(10
–
55)
(3
–
25)
(10
–
55)
(3
–
40)
1/8
–
63/64
Below
1/8
–
63/64
(3
–
25)
1/4(6)
(3
–
25)
Below 1/4(6)
Table 1
List of appropriate blades
NOTE:
⅜
The minimum cutting radius of No. 1 (Long), No. 1 ( Super Long), No. 21, No. 22 and No. 41 blades is 3-15/16" (100 mm).
⅜
No. 1 (Long), No. 1 ( Super Long), No. 11, No. 12, No. 15, No. 16, No. 21, No. 22 and No. 97 blades are sold separately.
Blade
Material quality General lumber Plywood Mild steel plate Stainless steel plate Aluminium copper, brass Aluminium sash Phenol resin, melamin resin, etc. Vinyl chloride, acryl resin, etc. Foamed polyethyl- ene, foamed styrol Card board, corrugated paper Hardboard Fiberboard
Material to be cut Lumber Iron plate Nonferrous metal Plastics Pulp