Husqvarna 340 EPA II - Manual (Page 34)

34
– English
Engine
Cylinder volume, cu.in/cm 3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 9000 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths, inches/cm
Usable cutting length, inches/cm
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive link, inch/mm
Number of teeth on drive sprocket
TECHNICAL DATA
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
13 0,325" 10T Husqvarna H30 or
15 0,325" 10T Oregon 95VP
16 0,325" 10T
18 0,325" 10T
15 0,325" 10T Husqvarna H25 / S24 or
16 0,325" 10T Oregon 21BP / 34LG or 34SL
18 0,325" 10T
20 0,325" 12T
Recommended original and replacement
bar and chain combinations
Following is a list of recommended cutting equipment for the
Husqvarna chain saw models 340, 345 and 350. The combinations of
powerhead, bar and chain have been investigated in accordance with
the kickback and vibration requirements of ANSI B 175.1 – 2000.
The guide bar nose radius is determined by either the maximum
number of teeth in the nose sprocket or the corresponding maximum
nose radius of a solid bar.
The following list is the chain saw manufacturers recommendations.
There may be other combinations available, which will also achieve
kickback protection.
As we are listing the maximum guide bar nose radius, you may use a
guide bar with smaller nose radius than in our list. For guide bars of the
same length, all sprocket-nose guide bars of the same pitch and
having the same number of of sprocket teeth may be considered to
have equivalent kickback energy. A hard nose bar having the same
length and nose radius as a sprocket-nose bar may be considered to
have equivalent or less kickback energy than the sprocket-nose bar.
Low kickback saw chain is a chain which has only met the kickback
performance requirements of ANSI B 175.1 safety requirements for
gasoline-powered chain saws when tested on the representative
sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We
recommend that you as replacement use the listed chains or "Low
kickback saw chains" which are available at your dealer.
340
2,49/40,8
1,57/40
1,28/32
2 700
2,0/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
9
0,53/0,25
Automatic
10,3/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
345
2,75/45,0
1,65/42
1,28/32
2 700
2,2/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
9
0,53/0,25
Automatic
10,3/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
350
3,15/51,7
1,77/45
1,28/32
2 700
2,3/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
5-12
0,55/0,26
Automatic
10,6/4,8
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"1,6
7
0,050"/1,3 mm H30/95VP 20BP 33LG 33SL
0,058"/1,5 mm – H25/21BP 34LG 34SL
0,063"/1,6 mm – 22BP 35LG 35SL
Note: For the chains above you are free to choose between 0,050",
0,058 and 0,063" gauge drive link for the corresponding bar, see
table below.
´®z+H+Q¶5N¨