Honeywell TE532ELW User Manual

Page 3

Advertising

The unit is in a searching mode.

Temperature and readings is

securely registered.

No signals detected.

- - -

GETTING STARTED

WEATHER DISPLAY

After batteries are installed; remote sensor will transmit

temperature and humidity data at 45 second intervals. The

main unit may take up to two minutes to receive the initial

readings. Upon successful reception, remote temperature

will appear under the weather forecast section of the main

unit’s display (the default remote channel is channel one).

The main unit will automatically update readings at 45-

second intervals.

After communication between the main unit and remote

sensor has been established, secure the remote sensor in

the desired location.

If no signal is received from the remote sensor within two

minutes, dashes [- - -] will be displayed. Press and hold the

DOWN ( ) button on the main unit for two seconds to

initiate another signal search.

PLACEMENT OF THE UNITS

The main unit can be placed on any flat surface indoors.

The remote sensor can be placed indoors or outdoors, on

a flat surface or mounted on the wall.

NOTE: When the temperature falls below freezing, the

batteries in the outdoor remote sensor may have reduced

voltage supply and a shorter effective range. We

recommend using lithium batteries at temperatures of

32°F (0°C) and below.
BATTERY INSTALLATION

REMOTE SENSOR

NOTE: Install the batteries; select the channel and

temperature in °C or °F before mounting the remote

sensor.

• Remove the screws from the battery compartment with a

small Phillips screwdriver.

• Set the channel. The switch is located in the battery

compartment. Channel 1 is typically selected if only one

remote sensor is being used.

• Install 2 “AAA” size alkaline batteries (not included)

matching the polarities shown in the battery compartment.

• Replace the battery compartment door and secure the

screws.

• Secure the remote sensor in the desired location.

MAIN UNIT

• Remove the battery compartment door.

• Install 2 batteries (UM-3 or “AA” size 1.5V) matching

the polarity as shown in the battery compartment.

• Replace the battery compartment door.

LOW BATTERY WARNING

A low-battery indicator [ ] will appear next to the indoor

or remote data reading line of the main unit warning that

the corresponding batteries need replacement.

REMOTE AND INDOOR TEMPERATURE & HUMIDITY

The remote temperature and humidity information line is

located right below the weather forecast line of the main

unit’s display.

The wave icon is located above the remote channel number

indicates the reception status from the corresponding remote

sensor.

There are three following types of the reception status may

be displayed:

The indoor temperature and humidity with the icon is

located below the remote temperature and humidity

information line.

NOTE: If the indoor or remote temperature or humidity

goes above or below operating range stated in

specifications, the main unit’s display ( weather) will show

dashes “- - -” on the corresponding line.
AUTO-SCANNING

Press and hold the CHANNEL button for 2 seconds – the

icon “ ” will appear on the main unit display to the left

of the COMFORT LEVEL indicator.

All three remote channels data will be displayed one-by-

one automatically with 11 seconds delay in the following

sequence: Channel 1, Channel 2 and Channel 3.

To exit from scanning mode, press and hold the

CHANNEL button for 2 seconds, and the icon “ ” will

disappear, returning the main unit display to the default

display mode.

PROGRAMMABLE TEMPERATURE ALARM

This product allows manual programming of a HIGH and

LOW temperature alarms for all three remote channels at

the same time. Once the actual remote temperature will

reach the pre-set high or low limits, the alarm will sound.

The alarm can be set for temperature readings between -58 °F

and 158°F.

To program the temperature alarm for all three remote

channels,

• Press the TEMP AL button once to enter into the High

Temperature Alarm programming mode – the

abbreviation “OF” with the high temperature limit

symbol ( ) will be displayed on the remote

temperature line

• Press and hold TEMP AL button until the abbreviation

“OF” will flash

• Use UP( ) or DOWN( ) arrow buttons to adjust the

higher temperature limit

• Press the TEMP AL button to confirm the selected value

• Press the TEMP AL button once to enter into the Low

Temperature Alarm programming mode – the

abbreviation “OF” with the low temperature limit