Honeywell DCP552 Mark II - Manual (Page 105)

7-6
Item code Item No.
User
settings
Settings and descriptions
Factory default
settings
PA 24 Manipulated variable
deviation limit (CH2)
24 0.1 to 110.0% OUT/0.1 sec 110.0
PA 25 Time proportional output
cycle (CH2)
25 1 to 240 sec 10
PA 26 ON-OFF control Differential
(CH2)
26 0 to 1000 SPU (CH2) 50
PA 27 PID computation initialize
manipulated variable (CH2)
27 -5.0 to 105.0% 0.0
PA 28 Unused 28 [Description:]
Ò-----Óis displayed and setting cannot be performed.
-----
PA 29 Unused 29 -----
PA 30 Unused 30 -----
PA 31 Event on delay
Group 1 event number
31 0 to 16
[Description:]
A setting of 0 generates no delay.
0
PA 32 Event on delay
Group 1 delay time
32 0.0 to 3000.0sec
[Description:]
When PA31 is set to 0, Т-----У is displayed and setting cannot be performed.
0.0
PA 33 Event on delay
Group 2 event number
33 0 to 16
[Description:]
A setting of 0 generates no delay.
0
PA 34 Event on delay
Group 2 delay time
34 0.0 to 3000.0sec
[Description:]
When PA33 is set to 0, Т-----У is displayed and setting cannot be performed.
0.0
PA 35 Event on delay
Group 3 event number
35 0 to 16
[Description:]
A setting of 0 generates no delay.
0
PA 36 Event on delay
Group 3 delay time
36 0.0 to 3000.0sec
[Description:]
When PA35 is set to 0, Т------У is displayed and setting cannot be performed.
0.0
PA 37 Event on delay
Group 4 event number
37 0 to 16
[Description:]
A setting of 0 generates no delay.
0
PA 38 Event on delay
Group 4 delay time
38 0.0 to 3000.0sec
[Description:]
When PA37 is set to 0, Т-----У is displayed and setting cannot be performed.
0.0
PA 39 FAST X 39 0
PA 40 CP computation temperature
compensation
40 -1000 to +1000 PVU (CH1)
[Description:]
Т-----У is displayed for models without CP compensation
and setting can not be performed.
0
PA 41 Unused 41 [Description:]
Ò-----Óis displayed and setting cannot be performed.
0
PA 42 Unused 42 0
PA 43 PID computation initialize
(CH1)
43 0
PA 44 PV2 message display mode 44 0: CP or PO 2 value display
1: mV value display
2: O 2 sensor impedance value display
0
PA 45 G.SOAK time (CH1) 45 0.1 to 60.0sec 2.0
PA 46 G.SOAK time (CH2) 46 0.1 to 60.0sec 2.0
0 : 2X
1 : 10X
2 : 60X
3 : 120X
[Description:]
When setup data C62 is set to 1 (program time unit: minutes,
seconds), settings 3 and 4 produce a speed of 10 X.
When C62 is set to 2 (program time unit: 0.1sec), the FAST
mode is not available.
0: No initialization during advance processing and PID group
change.
1: Initializes during advance processing but not during PID
group change.
2: No initialization during advance processing but initializes
during PID group change
3: Initializes both during advance processing and PID group
change
Chapter 7. PARAMETER SETUP