Honeywell DCP552 Mark II - Manual (Page 124)

7-25
0 to 16 : t/c
48 to 52 : linear (DC current, DC voltage)
64 to 71 : RTD
96 to 103: RTD
128 to 134: linear (DC current, DC voltage)
135 : O
2
Sensor
[Description:]
Setting 135 cannot be made on a model without CP
compensation. A model with CP compensation is tied to
setting 135. For details see range numbers listed in
Section 2-3, ÒInput Types and Range NumbersÓ (page 2-8).
0 C 11 11 PV2 range number
0: ûC Celsius
1: ûF Fahrenheit
[Description:]
When the C01 setting is set to linear or O
2
sensor, [----]
is displayed and setting cannot be performed.
0 C 12 12 PV2 temperature unit
0 to 2
A setting of 0 means no decimal point and a setting of 1 and 2
indicates the number of decimal digits.
[Description:]
When the C11 setting is set to linear or O
2
sensor, [----] is
displayed and setting cannot be performed.
The setting range varies with the C11 and C12 setting.
¥ A setting between 0 and 2 can be made when C11 is set to:
and C12 is set to 0.
C11 settings: 66, 68, 69, 98, 100, 101 and C12 is set to 1.
¥ A setting of 0 and 1 can be made when C11 is set to: 0 to 4,
6, to 14, 16, 64, 70, 71, 96, 102, 103and C12 is set to 0,
when C11 is set to: 0 to 5, 7, 8, 10, 12 to 14, 16, 64, 65, 67,
70, 71, 96, 97, 99, 102, 103and C12 is set to 1.
¥ Only a setting of 0 is possible when C11 is set to: 6, 9, 11
and C12 is set to 1 .
¥ When the C11 setting is for t/c or RTD, this setting is
reflected in PVU (PV2) units.
1 C 13 13 PV2 decimal point position
0 to 4
A setting of 0 means no decimal point and a setting
between 1 and 4 indicates the number of decimal digits.
[Description:]
When the C11 setting is set to t/c, RTD, or O
2
sensor, [---
-] is displayed and setting cannot be performed.
When setting C11 is linear, this setting is reflected in
PVU (PV2) units.
1 C 14 14 PV2 linear decimal point
position
0 PVU
C 15 15 PV2 linear range lower limit
10000PVU C 16 16 PV2 linear range upper limit
0: Yes (compensated internally)
1: No (compensated exernally)
[Description:]
When the C11 setting is set to RTD, linear or O
2
sensor, [----] is
displayed and setting cannot be performed.
0 C 17 17 PV2 cold junction
compensation
0: No
1: Yes
[Description:]
When the C11 setting is set to t/c, RTD or O
2
sensor, [----] is
displayed and setting cannot be performed.
0 C 18 18 PV2 square root extraction
0.2 to 10.0 % (ratio depends on input range)
[Description:]
When the C11 setting is set to t/c, RTD or O
2
sensor, [----] is
displayed and setting cannot be performed.
0.2 C 19 19 PV2 square root extraction
dropout
-1.0 to +1.0ûC
[Description:]
When the C11 setting is set to RTD, linear or O
2
sensor, [----] is
displayed and setting cannot be performed.
Use 0.0 for normal settings.
0.0 C 20 20 PV2 cold junction bias
Item code Item No.
User
settings
Settings and descriptions
Factory default
settings
Ð19999 to +20000 PVU (PV2)
[Description:]
When the C11 setting is set to t/c, RTD, or O
2
sensor, [---
-] is displayed and setting cannot be performed.
Reversing the lower limit and upper limit makes it
possible to reverse analog inputs and specified values.
Chapter 7. PARAMETER SETUP