haier BRF1- 120 - Manual (Page 6)

4.00m
Model
BRF1-120W
PJF1-120W
BRF1-150W
PJF1-150W
Volume
Water-proof
Grade
120L
150L
Drip-proof
Drip-proof
Rated internal
Pressure Size
Model Rated voltage Frequency Lighting area
BRF1-120W
BRF1-150W 220V~
220V~ 50Hz
50Hz
2000W
2000W
0.75MPa
0.75MPa
492 530 1160(mm)
492 530 1380(mm)
2.51m
2
PJF1-120W
PJF1-150W
220V~
220V~
50Hz
50Hz
2000W
2000W
3.02m
3.00m
2
2
2
3 12
Note: the above parameter errors ( except power value) of the lighting area are 3%,
volume errors are 3%, and the allowed error scope of other sizes is 10%.
Name of components Packing method
Packing container
o f w a t e r t a n k
BRF1-120/150W PJF1-120/150W
Water-storing tank
Safety valve
Large expanding bolt
Users manual
Exhaust valve
Model
Tee joint
¼ ¯ И И Ж ч ° ь Ч ° П д
Pump
water pump joint 1
water pump joint 2
Screw nut
Rubber spacer
Opposite wires S1/2F-3/4M
Packing of pump
3/4 fiber spacer
Collector equipment
Single-direction valve
1
1
4
1
1
1
1
1
2
1
1
Packing of collector
Note: accessories of BRF1-120/150W and PJF1-120/150W products are suitable only for
oblique installment. For flat installment, prop stand of different angles should be made
according to requirements, which is not included in the packing accessories.
Assistant power
Fig.7 and at this time, only power supply
key is effective and other keys are
ineffective. The interface only displays
water temperature of water-storing
tank and the temperature of water
e x i t i n g o f c o l l e c t o r e q u i p m e n t .
However, when the system is turned off,
the solar heating and malfunction
alarm protection are all working and
only if the conditions for the running of
the water pump are Satisfied, water
pump will run at full speed. When
malfunction alarm appears, it will
display malfunction code.
B.Selection of working mode: the system
provides four working modes, and
customers can select any mode as the
present working mode. When the
system is turned on, press the mode
key, and the system will circularly
exchange in order of solar energy
heating, simultaneous heating, preset
h e a t i n g a n d i n t e l l e c t u a l h e a t i n g .
Meanwhile, the corresponding icon
point will be on. Press mode key to
c h o o s e a c e r t a i n m o d e a n d s t o p
pressing mode key for six seconds,
then the system will automatically enter
this mode.
C. Parameter setting in all modes: to press
the setting key can set the following
parameters: clock, preset time, heating
t e m p e r a t u r e , a n d t e m p e r a t u r e
difference value of water pump running.
The number tube in the set parameter
indicates glisteningly. To press the
adjusting key
to adjust
numbers (to continually press
more than one second, the adjusted
parameter will increase progressively 3
numbers every second; to continually
Fig.8 Temperature difference
setting interface for water pump
TD
PRE
HEAT MODE
SET
CT
Fig.6 Solar heating interface
Fig.7 Turning off interface
SOL
WP CLK
Fig.9 Temperature setting
Interface for the first
time Preset heating
HEAT
MODE
SET
SOL
HEAT
MODE
SET
HEAT
MODE
SET
Technical parameter Packing list
Technical parameter
Packing list
Use method
`
1
1
1
Board hanging on door
Top cover for in-wall box
Bottom cover for in-wall box
4
4
1
1
W T H
C
W T H
C
W T H
C
W T H
C