Husqvarna 362XP - Manual (Page 34)

34
– English
Engine
Cylinder volume,
cu.in/cm
3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
Manufacturer
Carburetor type
Fuel capacity,
US pint/litre
Oil pump capacity at
8500 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain,
Lbs/kg
Chain/bar
Recommended bar
lengths, inches/cm
Usable cutting length,
inches/cm
Chain speed at max.
power, m/sec
Pitch, inch/mm
Thickness of drive link,
inch/mm
Number of teeth on
drive sprocket
TECHNICAL DATA
Model 362
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
15 0,325 10T Husqvarna H25 / H21 or
16 0,325 10T Oregon 21VB / 21LP
18 0,325 10T
20 0,325 12T
15-24 3/8 11T Husqvarna H42 / EM S48 or
Oregon 73VL / 73LG / 73L
Model 365 and 371
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
15-28 3/8 11T Husqvarna H42 / EM S48 or
Oregon 73VL / 73LG / 73L
0,058"/1,5 mm H25 H21 H42 EM S48 21VB 21LP 73VL 73LG 73L
0,050"/1,3 mm – – – – 20VB 20LP 72VL 72LG 72L
Recommended original and replacement
bar and chain combinations
These Husqvarna saw models are in the ANSI category of saws
above 3,8 cu. in. and are not
required to comply with low kickback
performance requirements. However, for these models we
recommend the following cutting equipment.
WARNING! These models of chain saws are capable
of severe kickback that could result in serious
injuries to the user. Do not operate these saws unless
you have extraordinary cutting needs and experience
and specialized training for dealing with kickback.
Saws with significantly reduced kickback potential
are available. Always use the safest saw and cutting
equipment applicable to your cutting need.
!
Note: For the chains above you are free to choose between 0,050"
and 0,058" gauge drive link for the corresponding bar, see the table
below.
The combinations of powerhead, bar and chain have been
investigated in accordance with the vibration requirements of
ANSI B 175.1-1991.
362XP
3,8/62,4
1,85/47
1,4/36
2 700
3,4/ 9 600
FHP
CD
Champion
RCJ7Y
0,02/0,5
Walbro
HD6
1,63/0,77
4–20
0,89/0,42
Automatic
13,2/6,0
XPG:13,7/6,2
13-24"/33-61
12-23"/31-58
21,4
3/8"/ 9,52
0,325"/ 8,25
0,058"/1,5
7
371XP
4,3/70,7
1,97/50
1,4/36
2 700
3,9/ 9 600
FHP
CD
Champion
RCJ7Y
0,02/0,5
Walbro
HD12
1,63/0,77
4–20
0,89/0,42
Automatic
13,0/5,9
XPG:13,4/6,1
15-28"/38-71
14-27"/35-69
21,4
3/8"/ 9,52
0,058"/1,5
0,050"/1,3
7
365
4,0/65,1
1,89/48
1,4/36
2 700
3,4/ 9 300
FHP
CD
Champion
RCJ7Y
0,02/0,5
Zama
C3M-EL8
1,63/0,77
4–20
0,89/0,42
Automatic
13,2/6,0
15-28"/38-71
14-27"/35-69
20,7
3/8"/ 9,52
0,058"/1,5
0,050"/1,3
7
´*3$G¶54¨