Honeywell TN924W - Manual (Page 11)

21
• Press MENU/SELECT button entering into the language programming mode
• Press ▲ or ▼ selecting English, Spanish or French
• Press MENU/SELECT button to confirm – the unit will beep once confirming
the language selection
• Press ◄ to exit
ALERTS SELECTION
Your Weather Radio contains all NWR events (alerts) pre-programmed; many of them
are set to ON by default.
There are three events (alerts) categories may be displayed – Advisory, Watch or
Warning
Advisory-
an advisory is issued when a hazardous weather or hydrologic event is
occurring, imminent or likely. Advisories are for less serious conditions than warnings,
which cause significant inconvenience and if caution is not exercised, could lead to
situations that may threaten life or property
.
Watch – alerts you to potential severe weather approaching your area. It does not mean
severe weather occur, but that the right conditions exist which could lead to severe
storms. You should be prepared for the weather to deteriorate rapidly.
Warning – states the severe weather is imminent or present in your vicinity. You should
immediately take precautions to protect yourself and your family.
Please see page 59 for a list of NWS events (alerts) and decide what events you would
like to receive and what you would like to disable.
Use this procedure for programming Weather Radio alerts:
• Press MENU/SELECT button entering into the programming mode until
SELECT CH message is displayed
• Press ▲or ▼button until the SET ALERTS? message will be displayed
• Press MENU/SELECT button entering into the alerts programming mode
• Press ▲ or ▼ selecting ADVISORY, WATCH or WARNING
• Press MENU/SELECT button to select the event type – the first specific event
will be scrolling on the display
• Press ▲or ▼button selecting ALERT ON or ALERT OFF
• Press MENU/SELECT button to select and confirm the setting
• Press ◄ to exit
22
PROGRAMMING YOUR LOCATION
The NWR radio channels work the same as regular radio.
Your Weather Radio is pre-programmed with seven NOAA broadcast frequencies
(channel1-7):
1 2 3 4 5 6 7
162.400MHz 162.425MHz 162.450MHz 162.475MHz 162.500MHz 162.525MHz 162.550MHz
After the strongest available channel has been detected by your Weather Radio, all
FIPS codes specific for your location (state and county) are automatically pre-set.
You have an option to program events that are happening in your surrounding area by
programming or deleting of SAME (FIPS) codes.
WARNING: Your Weather Radio has an option of changing FIPS codes, however prior
to changing any of the pre-programmed codes; you must verify its correction with the
NWS (National Weather Service).
• Press MENU/SELECT button entering into the programming mode until
SELECT CH message is displayed
• Press ▲or ▼button until the LOCATION message will be displayed
• Press MENU/SELECT button entering into the location programming mode
• Press ▲ or ▼ selecting ALL, SIGNLE or MULTIPLE
ALL option allows receiving all of the existing SAME alerts within a 50 mile radius. There
is no location for editing.
• Press MENU/SELECT button to confirm selected location
• Press ◄ to exit
Single option allows receiving a SAME alert signals for only one programmed location.
Multiple option allows receiving a SAME alert signals only for pre-programmed locations
(up to 9).
In Multiple or Single option:
• Press MENU/SELECT button to confirm selected location
• Press MENU/SELECT button – the message EDIT? will be displayed. You can
edit this single location FIPS code
• Press ▲or ▼button selecting between messages: EDIT? or DELETE?
• Press MENU/SELECT button to select EDIT or DELETE. If you want to edit the
SAME county code, press ► after county name is displayed.
• Press ▲or ▼button selecting new state and county
• Press MENU/SELECT button to select and confirm the setting
• Press ◄ to exit
• Press ▲or ▼button selecting EMPTY location or a location to edit
• Press MENU/SELECT button to confirm your selection
• Press ◄ to exit \