Directory Brands Graco Inc. 234032

Instruction Manuals and User Guides 234032 Graco Inc.

We have 1 Instruction Manual and User Guide for 234032 Graco Inc.

  • Graco Inc. 234032 (20 pages)
    English: +

    Summary of Contents
    • p. 1/20
      Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001 309523D Instructions XTR ™ Airless Spray Gun Part No. 233889, Series A Heavy Duty RAC tip guard, 519 SwitchTip ™ Part No. 234032, Series A Standard
    • p. 2/20
      Contents 2 309523D Contents Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . 4 Grounding
    • p. 3/20
      Warning 309523D 3 WARNING INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate medical attention. • Do not
    • p. 4/20
      System Requirements 4 309523D System Requirements • Install a bleed-type master air valve on a pneumatic pump air supply line to relieve air trapped between this valve and the pump after air regulator is shut off. Trapped air can cause the pump to cycle
    • p. 5/20
      Grounding 309523D 5 Grounding Check your local electrical code and pump/sprayer man-ual for detailed grounding instructions. • Spray gun: ground through connection to a grounded fluid hose and pump/sprayer. • Fluid hose: use only grounded hoses. • Fluid
    • p. 6/20
      Pressure Relief Procedure 6 309523D Pressure Relief Procedure 7. If you suspect that pressure is not fully relieved because: • Spray tip is clogged SwitchTip: Follow procedure on page 10. Flat Tip: Very slowly loosen tip guard retaining nut and relieve pressure
    • p. 7/20
      Operating Gun 309523D 7 Operating Gun 7. Trigger gun full-open or full-close. Hold gun at right angles to work surface. Do not swing gun in an arc. Practice to find the best length and speed of stroke. Strain the fluid if it contains particles that could
    • p. 8/20
      Operating Gun 8 309523D Adjusting Spray Pattern Spray Pattern Size The spray tip orifice and spray angle determine pattern coverage and size. When you need more coverage, use a larger spray tip rather than increasing fluid pressure. Spray Pattern Direction
    • p. 9/20
      Maintenance 309523D 9 Maintenance Cleaning Spray Tip and Tip Guard 2. Clean spray tip with a solvent-soaked brush. • Clean front of tip frequently to reduce fluid buildup. • Clean tip and tip guard at end of each work day. WARNING Read warnings, page 3.
    • p. 10/20
      Maintenance 10 309523D If RAC Spray Tip Clogs 1. If spray tip clogs while spraying, stop spraying immediately. 8. If tip is still clogged: WARNING Read warnings, page 3. 2. Engage trigger lock. 3. Rotate RAC tip handle back 180° (arrow points back). 4. Disengage
    • p. 11/20
      Flushing 309523D 11 Flushing Flush pump and gun before fluid can dry in it. If avail-able, use flushing procedure provided in your pump or sprayer manual instead of this procedure. 6. Trigger gun into solvent pail. Circulate fluid until system is thoroughly
    • p. 12/20
      Repair 12 309523D Repair Disassembly 1. Follow Pressure Relief Procedure, page 6. Engage trigger lock. 8. Clean and replace parts as needed. Repair Kit 245876 is available. Parts included with the kit are marked with *. 2. Disconnect fluid hose. Remove tip
    • p. 13/20
      Repair 309523D 13 If you need to remove trigger 1. Using a wrench, remove lock nut (13) from trigger stud (14). 2. Slide trigger stud (14) out of gun body, and remove trigger (5). Assembly - continued - To avoid losing parts, be ready for two actuator pins
    • p. 14/20
      Repair 14 309523D Test gun before using 4. Release trigger; the gun should immediately stop spraying and there should not be any leaks. If there is a problem, follow Pressure Relief Pro-cedure on page 6, engage trigger lock, and dis-connect fluid hose. Check
    • p. 15/20
      Repair 309523D 15
    • p. 16/20
      Parts 16 309523D Parts Part No. 233889, Series A Heavy Duty RAC tip guard, 519 SwitchTip ™ Part No. 234032, Series A Standard (nonreversing) Dripless ™ tip guard, 519 flat tip 17a† T12174B 2* 12* 3* 6 14 1 11* 4* 8 9 10 19 15 16 5 13 18a ★ 17b† 17c† 18b
    • p. 17/20
      Parts 309523D 17 Part No. 233889, Series A Heavy Duty RAC tip guard, 519 SwitchTip ™ * Parts included in Repair Kit 245876, purchased sepa-rately. Installation tool included. † Parts not available separately. Order kit 245994 (see kit instructions 406554).
    • p. 18/20
      Parts 18 309523D Accessories Part No. 245878: 2-Finger Trigger Kit Part No. 236987: Inlet Swivel 1/4 npsm Part No. 246291: Gun Filter Swivel 1/4 npsm (not shown) Part No. 194744: Packing Repair Tool Included in Repair Kit 245876 Front Extension: 7/8-14 UNF-2B
    • p. 19/20
      Technical Data 309523D 19 Technical Data *Results are maximum readings taken at 6000 psi (41 MPa, 414 bar), with HD427 tip, using water. Sound power level was tested to ISO 3744-1981. Dimensions Maximum Working Pressure. . . . . . . . . . . . . . . . . .
    • p. 20/20
      All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Sales Offices: Minneapolis, Detroit International Offices: