Document Outline

• Chapter 1 Switch Management
  • 1.1 Management Options
    • 1.1.1 Out-Of-Band Management
    • 1.1.2 In-band Management
    • 1.1.3 Management Via Telnet
    • 1.1.4 Management Via HTTP
  • 1.2 Management Interface
    • 1.2.1 CLI Interface
    • 1.2.2 Configuration Modes
      • 1.2.2.1 User Mode
      • 1.2.2.2 Admin Mode
      • 1.2.2.3 Global Mode
      • 1.2.2.4 Interface Mode
      • 1.2.2.5 VLAN Mode
      • 1.2.2.6 DHCP Address Pool Mode
      • 1.2.2.7 Route Mode
      • 1.2.2.8 ACL Mode
    • 1.2.3 Configuration Syntax
    • 1.2.4 Shortcut Key Support
    • 1.2.5 Help Function
    • 1.2.6 Input Verification
    • 1.2.7 Fuzzy Match Support
  • 1.3 Web Management
    • 1.3.1 Main Page
    • 1.3.2 Module Front Panel
• Chapter 2 Basic Switch Configuration
  • 2.1 Commands for Basic Switch Configuration
    • 2.1.1 Commands for Basic Configuration
      • 2.1.1.1 authentication login
      • 2.1.1.2 calendar set
      • 2.1.1.3 config
      • 2.1.1.4 debug ssh-server
      • 2.1.1.5 dir
      • 2.1.1.6 enable
      • 2.1.1.7 enable password
      • 2.1.1.8 exec-timeout
      • 2.1.1.9 exit
      • 2.1.1.10 help
      • 2.1.1.11 hostname
      • 2.1.1.12 ip host
      • 2.1.1.13 ipv6 host
      • 2.1.1.14 ip http server
      • 2.1.1.15 login
      • 2.1.1.16 language
      • 2.1.1.17 login local
      • 2.1.1.18 password
      • 2.1.1.19 ping
      • 2.1.1.20 ping6
      • 2.1.1.21 reload
      • 2.1.1.22 service password-encryption
      • 2.1.1.23 service terminal-length
      • 2.1.1.24 set default
      • 2.1.1.25 setup
      • 2.1.1.26 terminal length
      • 2.1.1.27 terminal monitor
      • 2.1.1.28 traceroute
      • 2.1.1.29 traceroute6
      • 2.1.1.30 cli username
      • 2.1.1.31 username password
      • 2.1.1.32 username nopassword
      • 2.1.1.33 write
  • 2.2 Monitor and Debug Command
    • 2.2.1 Ping
    • 2.2.2 Ping6
    • 2.2.3 Telnet
      • 2.2.3.1 Introduction To Telnet
      • 2.2.3.2 Telnet Configuration Task List
      • 2.2.3.3 Commands for Telnet
        • 2.2.3.3.1 telnet
        • 2.2.3.3.2 ip telnet server
        • 2.2.3.3.3 telnet-server securityip
    • 2.2.4 SSH
      • 2.2.4.1 Introduction to SSH
      • 2.2.4.2 SSH Server Configuration Task List
      • 2.2.4.3 Commands for SSH
        • 2.2.4.3.1 ssh-server authentication-retries
        • 2.2.4.3.2 ssh-server enable
        • 2.2.4.3.3 ssh-server host-key create rsa
        • 2.2.4.3.4 ssh-server timeout
        • 2.2.4.3.5 ssh-user
      • 2.2.4.4 Typical SSH Server Configuration
    • 2.2.5 Traceroute
    • 2.2.6 Traceroute6
    • 2.2.7 Show
      • 2.2.7.1 Commands for Show
        • 2.2.7.1.1 show calendar
        • 2.2.7.1.2 show debugging
        • 2.2.7.1.3 show history
        • 2.2.7.1.4 show memory
        • 2.2.7.1.5 show running-config
        • 2.2.7.1.6 show ssh-server
        • 2.2.7.1.7 show ssh-user
        • 2.2.7.1.8 show startup-config
        • 2.2.7.1.9 show interface switchport
        • 2.2.7.1.10 show users
        • 2.2.7.1.11 show tcp
        • 2.2.7.1.12 show udp
        • 2.2.7.1.13 show version
    • 2.2.8 Debug
    • 2.2.9 System log
      • 2.2.9.1 System Log Introduction
        • 2.2.9.1.1 Log Output Channel
        • 2.2.9.1.2 Format And Severity Of The Log Information
      • 2.2.9.2 System Log Configuration
        • 2.2.9.2.1 System Log Configuration Task Sequence
        • 2.2.9.2.2 System Log Configuration Command
          • 2.2.9.2.2.1 show logging buffered
          • 2.2.9.2.2.2 clear logging
          • 2.2.9.2.2.3 logging host
      • 2.2.9.3 System Log Configuration Example
  • 2.3 Configurate Switch IP Addresses
    • 2.3.1 Switch IP Addresses Configuration Task List
    • 2.3.2 Commands For Configuring Switch IP
      • 2.3.2.1 ip address
      • 2.3.2.2 ip address bootp-client
      • 2.3.2.3 ip address dhcp-client
  • 2.4 SNMP Configuration
    • 2.4.1 Introduction To SNMP
    • 2.4.2 SNMP Configuration Task List
    • 2.4.3 Commands for SNMP
      • 2.4.3.1 rmon
      • 2.4.3.2 show snmp
      • 2.4.3.3 show snmp status
      • 2.4.3.4 snmp-server community
      • 2.4.3.5 snmp-server
      • 2.4.3.6 snmp-server enable traps
      • 2.4.3.7 snmp-server host
      • 2.4.3.8 debug snmp mib
      • 2.4.3.9 debug snmp keneral
      • 2.4.3.10 show snmp engineid
      • 2.4.3.11 show snmp group
      • 2.4.3.12 show snmp mib
      • 2.4.3.13 show snmp user
      • 2.4.3.14 show snmp view
      • 2.4.3.15 snmp-server engineid
      • 2.4.3.16 snmp-server group
      • 2.4.3.17 snmp-server SecurityIP enable
      • 2.4.3.18 snmp-server view
      • 2.4.3.19 snmp-server user
      • 2.4.3.20 snmp-server securityip
    • 2.4.4 Typical SNMP Configuration Examples
    • 2.4.5 SNMP Troubleshooting
  • 2.5 Switch Upgrade
    • 2.5.1 Switch System Files
    • 2.5.2 BootROM Upgrade
    • 2.5.3 FTP/TFTP Upgrade
      • 2.5.3.1 Introduction To FTP/TFTP
      • 2.5.3.2 FTP/TFTP Configuration
        • 2.5.3.2.1 FTP/TFTP Configuration Task List
        • 2.5.3.2.2 Commands for Switch Upgrade
          • 2.5.3.2.2.1 copy（FTP）
          • 2.5.3.2.2.2 copy（TFTP）
          • 2.5.3.2.2.3 dir
          • 2.5.3.2.2.4 ftp-server enable
          • 2.5.3.2.2.5 ftp-server timeout
          • 2.5.3.2.2.6 show ftp
          • 2.5.3.2.2.7 show tftp
          • 2.5.3.2.2.8 tftp-server enable
          • 2.5.3.2.2.9 tftp-server retransmission-number
          • 2.5.3.2.2.10 tftp-server transmission-timeout
    • 2.5.4 FTP/TFTP Configuration Examples
    • 2.5.5 FTP/TFTP Troubleshooting
      • 2.5.5.1 FTP Troubleshooting
      • 2.5.5.2 TFTP Troubleshooting
  • 2.6 Security Feature Configuration
    • 2.6.1 Security Feature Introduction
    • 2.6.2 Security Feature Configuration
      • 2.6.2.1 Prevent IP Spoofing Function Configuration Task Sequence
      • 2.6.2.2 Prevent TCP Unauthorized Label Attack Function Configuration Task Sequence
      • 2.6.2.3 Anti Port Cheat Function Configuration Task Sequence
      • 2.6.2.4 Prevent TCP Fragment Attack Function Configuration Task Sequence
      • 2.6.2.5 Prevent ICMP Fragment Attack Function Configuration Task Sequence
    • 2.6.3 Commands for Security Feature
      • 2.6.3.1 dosattack-check srcip-equal-dstip enable
      • 2.6.3.2 dosattack-check ipv4-first-fragment enable
      • 2.6.3.3 dosattack-check tcp-flags enable
      • 2.6.3.4 dosattack-check srcport-equal-dstport enable
      • 2.6.3.5 dosattack-check tcp-fragment enable
      • 2.6.3.6 dosattack-check tcp-header
      • 2.6.3.7 dosattack-check icmp-attacking enable
      • 2.6.3.8 dosattack-check icmpv4-size
      • 2.6.3.9 dosattack-check icmpv6-size
    • 2.6.4 Security Feature Example
  • 2.7 Jumbo Configuration
    • 2.7.1 Jumbo Introduction
    • 2.7.2 Jumbo Configuration Task Sequence
    • 2.7.3 Jumbo Command
  • 2.8 sFlow Configuration
    • 2.8.1 sFlow introduction
    • 2.8.2 sFlow Configuration Task
    • 2.8.3 Commands for sFlow
      • 2.8.3.1 sflow destionation
      • 2.8.3.2 sflow agent-address
      • 2.8.3.3 sflow priority
      • 2.8.3.4 sflow header-len
      • 2.8.3.5 sflow data-len
      • 2.8.3.6 sflow counter-interval
      • 2.8.3.7 sflow rate
      • 2.8.3.8 show sflow
    • 2.8.4 sFlow Examples
    • 2.8.5 sFlow Troubleshooting
  • 2.9 TACACS+ Configuration
    • 2.9.1 TACACS+ Introduction
    • 2.9.2 TACACS+ Configurations
    • 2.9.3 Commands for TACACS+
      • 2.9.3.1 tacacs-server authentication host
      • 2.9.3.2 tacacs-server key
      • 2.9.3.3 tacacs-server timeout
      • 2.9.3.4 debug tacacs-server
    • 2.9.4 Typical TACACS+ Scenarios
    • 2.9.5 TACACS+ Troubleshooting
  • 2.10 Web Management
    • 2.10.1 Switch Basic Configuration
      • 2.10.1.1 Basic Configuration
      • 2.10.1.2 Configure Exec Timeout
    • 2.10.2 SNMP Configuration
      • 2.10.2.1 SNMP Manager Configuration
      • 2.10.2.2 Trap Manager Configuration
      • 2.10.2.3 Configure IP address of SNMP manager
      • 2.10.2.4 SNMP statistics
      • 2.10.2.5 RMON and trap configuration
    • 2.10.3 Switch upgrade
      • 2.10.3.1 TFTP client configuration
      • 2.10.3.2 TFTP server configuration
      • 2.10.3.3 FTP client configuration
      • 2.10.3.4 FTP server configuration
    • 2.10.4 Monitor And Debug Command
      • 2.10.4.1 Debug command
      • 2.10.4.2 Show vlan port property
      • 2.10.4.3 Others
    • 2.10.5 Switch Maintenance
      • 2.10.5.1.1 Exit current web configuration
      • 2.10.5.2 Save current running-config
      • 2.10.5.3 Reboot
      • 2.10.5.4 Reboot with the default configuration
    • 2.10.6 Telnet server configuration
    • 2.10.7 Telnet server user configuration
    • 2.10.8 Telnet security IP
• Chapter 3 Port Configuration
  • 3.1 Introduction to Port
  • 3.2 Port Configuration
    • 3.2.1 Network Port Configuration
      • 3.2.1.1 Network Port Configuration Task List
      • 3.2.1.2 Commands for Network Port Configuration
        • 3.2.1.2.1 combo-forced-mode
        • 3.2.1.2.2 clear counters
        • 3.2.1.2.3 description
        • 3.2.1.2.4 flow control
        • 3.2.1.2.5 interface Ethernet
        • 3.2.1.2.6 loopback
        • 3.2.1.2.7 mdi
        • 3.2.1.2.8 negotiation
        • 3.2.1.2.9 rate-limit
        • 3.2.1.2.10 rate-suppression
        • 3.2.1.2.11 show interface status
        • 3.2.1.2.12 shutdown
        • 3.2.1.2.13 speed-duplex
    • 3.2.2 VLAN Interface Configuration
      • 3.2.2.1 VLAN Interface Configuration Task List
      • 3.2.2.2 Commands for Vlan Interface
        • 3.2.2.2.1 interface vlan
        • 3.2.2.2.2 ip address
        • 3.2.2.2.3 shutdown
    • 3.2.3 Network Management Port Configuration
      • 3.2.3.1 Network Management Port Configuration Task List
      • 3.2.3.2 Commands for Network Management Port Configuration
        • 3.2.3.2.1 duplex
        • 3.2.3.2.2 interface Ethernet
        • 3.2.3.2.3 ip address
        • 3.2.3.2.4 loopback
        • 3.2.3.2.5 shutdown
        • 3.2.3.2.6 speed
  • 3.3 Port Mirroring Configuration
    • 3.3.1 Introduction to Port Mirroring
    • 3.3.2 Port Mirroring Configuration Task List
    • 3.3.3 Commands for Mirroring Configuration
      • 3.3.3.1 port monitor
      • 3.3.3.2 show port monitor
    • 3.3.4 Device Mirroring Troubleshooting
  • 3.4 Port Configuration Example
  • 3.5 Port Troubleshooting
  • 3.6 Web Management
    • 3.6.1 Ethernet port configuration
    • 3.6.2 Physical port configuration
    • 3.6.3 Bandwidth control
    • 3.6.4 Vlan interface configuration
    • 3.6.5 Allocate IP address for L3 port
    • 3.6.6 L3 port IP addr mode configuration
    • 3.6.7 Port mirroring configuration
    • 3.6.8 Mirror configuration
    • 3.6.9 Port debug and maintenance
    • 3.6.10 Show port information
• Chapter 4 Port Channel Configuration
  • 4.1 Introduction to Port Channel
  • 4.2 Port Channel Configuration Task List
  • 4.3 Commands for port channel
    • 4.3.1 debug lacp
    • 4.3.2 port-group
    • 4.3.3 port-group mode
    • 4.3.4 interface port-channel
    • 4.3.5 show port-group
  • 4.4 Port Channel Example
  • 4.5 Port Channel Troubleshooting
  • 4.6 Web Management
    • 4.6.1 LACP port group configuration
    • 4.6.2 LACP port configuration
• Chapter 5 VLAN Configuration
  • 5.1 VLAN Configuration
    • 5.1.1 Introduction to VLAN
    • 5.1.2 VLAN Configuration Task List
    • 5.1.3 Commands For Vlan Configuration
      • 5.1.3.1 Vlan
      • 5.1.3.2 private-vlan
      • 5.1.3.3 private-vlan association
      • 5.1.3.4 show vlan
      • 5.1.3.5 switchport access vlan
      • 5.1.3.6 switchport interface
      • 5.1.3.7 switchport mode
      • 5.1.3.8 switchport trunk allowed vlan
      • 5.1.3.9 switchport trunk native vlan
      • 5.1.3.10 switchport ingress-filtering
    • 5.1.4 Typical VLAN Application
  • 5.2 GVRP Configuration
    • 5.2.1 Introduction to GVRP
    • 5.2.2 GVRP Configuration Task List
    • 5.2.3 Commands for GVRP
      • 5.2.3.1 bridge-ext gvrp
      • 5.2.3.2 debug gvrp
      • 5.2.3.3 bridge-ext garp timer hold
      • 5.2.3.4 bridge-ext garp timer join
      • 5.2.3.5 bridge-ext garp timer leave
      • 5.2.3.6 bridge-ext garp timer leaveall
      • 5.2.3.7 show garp timer
      • 5.2.3.8 show gvrp configuration
    • 5.2.4 Typical GVRP Application
    • 5.2.5 GVRP Troubleshooting
  • 5.3 Dot1q-tunnel Configuration
    • 5.3.1 Dot1q-tunnel Introduction
    • 5.3.2 Dot1q-tunnel Configuration
      • 5.3.2.1 Configuration Task Sequence Of Dot1q-Tunnel
    • 5.3.3 Commands for Dot1q-Tunnel Configuration
      • 5.3.3.1 dot1q-tunnel enable
      • 5.3.3.2 dot1q-tunnel tpid
      • 5.3.3.3 show dot1q-tunnel
    • 5.3.4 Typical Applications Of The Dot1q-tunnel
    • 5.3.5 Dot1q-tunnel Troubleshooting
  • 5.4 VLAN-translation Configuration
    • 5.4.1 VLAN-translation Introduction
    • 5.4.2 VLAN-translation Configuration
      • 5.4.2.1 Configuration task sequence of VLAN-translation
    • 5.4.3 Commands for VLAN-Translation Configuration
      • 5.4.3.1 show vlan-translation
      • 5.4.3.2 vlan-translation
      • 5.4.3.3 vlan-translation enable
      • 5.4.3.4 vlan-translation miss drop
    • 5.4.4 Typical application of VLAN-translation
    • 5.4.5 VLAN-translation Troubleshooting
  • 5.5 Dynamic VLAN Configuration
    • 5.5.1 Dynamic VLAN Introduction
    • 5.5.2 Dynamic VLAN Configuration
      • 5.5.2.1 Dynamic VLAN Configuration Task Sequence
      • 5.5.2.2 Commands for Dynamic VLAN Configuration
        • 5.5.2.2.1 dynamic-vlan mac-vlan prefer
        • 5.5.2.2.2 dynamic-vlan subnet-vlan prefer
        • 5.5.2.2.3 mac-vlan
        • 5.5.2.2.4 protocol-vlan
        • 5.5.2.2.5 show dynamic-vlan prefer
        • 5.5.2.2.6 show mac-vlan
        • 5.5.2.2.7 show mac-vlan interface
        • 5.5.2.2.8 show protocol-vlan
        • 5.5.2.2.9 show subnet-vlan
        • 5.5.2.2.10 show subnet-vlan interface
        • 5.5.2.2.11 subnet-vlan
        • 5.5.2.2.12 switchport mac-vlan enable
        • 5.5.2.2.13 switchport subnet-vlan enable
    • 5.5.3 Typical Application Of The Dynamic VLAN
    • 5.5.4 Dynamic VLAN Troubleshooting
  • 5.6 Voice VLAN Configuration
    • 5.6.1 Voice VLAN Introduction
    • 5.6.2 Voice VLAN Configuration
      • 5.6.2.1 Voice VLAN Configuration Task Sequence
      • 5.6.2.2 Commands for Voice VLAN Configuration
        • 5.6.2.2.1 show voice-vlan
        • 5.6.2.2.2 switchport voice-vlan enable
        • 5.6.2.2.3 voice-vlan
        • 5.6.2.2.4 voice-vlan vlan
    • 5.6.3 Typical Applications Of The Voice VLAN
    • 5.6.4 Voice VLAN Troubleshooting
• Chapter 6 MAC Table Configuration
  • 6.1 Introduction to MAC Table
    • 6.1.1 Obtaining MAC Table
    • 6.1.2 Forward or Filter
  • 6.2 Commands for MAC address table configuration
    • 6.2.1 mac-address-table
    • 6.2.2 show mac-address-table
  • 6.3 Typical Configuration Examples
  • 6.4 Troubleshooting
  • 6.5 MAC Address Function Extension
    • 6.5.1 MAC Address Binding
      • 6.5.1.1 Introduction to MAC Address Binding
      • 6.5.1.2 MAC Address Binding Configuration Task List
      • 6.5.1.3 Commands for Mac Address Binding configuration
        • 6.5.1.3.1 clear port-security dynamic
        • 6.5.1.3.2 port-security
        • 6.5.1.3.3 port-security convert
        • 6.5.1.3.4 port-security mac-address
        • 6.5.1.3.5 port-security maximum
        • 6.5.1.3.6 port-security timeout
        • 6.5.1.3.7 port-security violation
        • 6.5.1.3.8 show port-security
        • 6.5.1.3.9 show port-security address
        • 6.5.1.3.10 show port-security interface
      • 6.5.1.4 Binding MAC Address Binding Troubleshooting
• Chapter 7 MSTP Configuration
  • 7.1 MSTP Introduction
    • 7.1.1 MSTP Region
      • 7.1.1.1 Operations Within An MSTP Region
      • 7.1.1.2 Operations between MST Regions
    • 7.1.2 Port Roles
    • 7.1.3 MSTP Load Balance
  • 7.2 MSTP Configuration Task List
  • 7.3 Commands for MSTP
    • 7.3.1 abort
    • 7.3.2 exit
    • 7.3.3 instance vlan
    • 7.3.4 name
    • 7.3.5 revision-level
    • 7.3.6 spanning-tree
    • 7.3.7 spanning-tree format
    • 7.3.8 spanning-tree forward-time
    • 7.3.9 spanning-tree hello-time
    • 7.3.10 spanning-tree link-type p2p
    • 7.3.11 spanning-tree maxage
    • 7.3.12 spanning-tree max-hop
    • 7.3.13 spanning-tree mcheck
    • 7.3.14 spanning-tree mode
    • 7.3.15 spanning-tree mst configuration
    • 7.3.16 spanning-tree mst cost
    • 7.3.17 spanning-tree mst port-priority
    • 7.3.18 spanning-tree mst priority
    • 7.3.19 spanning-tree portfast
    • 7.3.20 spanning-tree digest-snooping
    • 7.3.21 spanning-tree tcflush (global mode)
    • 7.3.22 spanning-tree tcflush (port mode)
  • 7.4 MSTP Example
  • 7.5 MSTP Troubleshooting
    • 7.5.1 Commands for Monitor And Debug
      • 7.5.1.1 show spanning-tree
      • 7.5.1.2 show spanning-tree mst config
      • 7.5.1.3 show mst-pending
      • 7.5.1.4 debug spanning-tree
  • 7.6 Web Management
    • 7.6.1 MSTP field operation
      • 7.6.1.1 Instance configuration
      • 7.6.1.2 Field operation
      • 7.6.1.3 Revision level control
    • 7.6.2 MSTP port operation
      • 7.6.2.1 Edge port setting
      • 7.6.2.2 Port priority setting
      • 7.6.2.3 Port route cost setting
      • 7.6.2.4 MSTP mode
      • 7.6.2.5 Link type configuration
      • 7.6.2.6 MSTP port configuration
    • 7.6.3 MSTP global control
      • 7.6.3.1 MSTP global protocol port configuration
      • 7.6.3.2 Forward delay time configuration
      • 7.6.3.3 Hello_time configuration
      • 7.6.3.4 Set the max age time for BPDU information in the switch
      • 7.6.3.5 Set the max hop count support for BPDU transmitting in MSTP field
      • 7.6.3.6 Set bridge priority of the specified instance for the switch
    • 7.6.4 Show MSTP setting
      • 7.6.4.1 Instance information
      • 7.6.4.2 MSTP field information
• Chapter 8 QoS And PBR Configuration
  • 8.1 QoS Configuration
    • 8.1.1 Introduction to QoS
      • 8.1.1.1 QoS Terms
      • 8.1.1.2 QoS Implementation
      • 8.1.1.3 Basic QoS Model
    • 8.1.2 QoS Configuration Task List
    • 8.1.3 Commands for QoS
      • 8.1.3.1 class
      • 8.1.3.2 class-map
      • 8.1.3.3 match
      • 8.1.3.4 set
      • 8.1.3.5 mls qos
      • 8.1.3.6 mls qos cos
      • 8.1.3.7 mls qos aggregate-policer
      • 8.1.3.8 mls qos trust
      • 8.1.3.9 mls qos dscp-mutation
      • 8.1.3.10 mls qos map
      • 8.1.3.11 police
      • 8.1.3.12 police aggregate
      • 8.1.3.13 policy-map
      • 8.1.3.14 queue mode
      • 8.1.3.15 service-policy
      • 8.1.3.16 wrr-queue bandwidth
      • 8.1.3.17 wrr-queue cos-map
    • 8.1.4 QoS Example
    • 8.1.5 QoS Troubleshooting
      • 8.1.5.1 Commands for Monitor And Debug
        • 8.1.5.1.1 show class-map
        • 8.1.5.1.2 show policy-map
        • 8.1.5.1.3 show mls qos aggregate-policer
        • 8.1.5.1.4 show mls qos interface
        • 8.1.5.1.5 show mls qos maps
        • 8.1.5.1.6 show mls-qos
  • 8.2 PBR Configuration
    • 8.2.1 Introduction to PBR
    • 8.2.2 PBR configuration
    • 8.2.3 PBR examples
• Chapter 9 L3 Forward Configuration
  • 9.1 Layer 3 Interface
    • 9.1.1 Introduction to Layer 3 Interface
    • 9.1.2 Layer 3 Interface Configuration Task List
    • 9.1.3 Commands for Layer 3 Interface
      • 9.1.3.1 interface vlan
  • 9.2 IP Configuration
    • 9.2.1 Introduction to IPv4, IPv6
    • 9.2.2 IP Configuration
      • 9.2.2.1 IPv4 address configuration
      • 9.2.2.2 Commands for IPv4 address
        • 9.2.2.2.1 ip address
      • 9.2.2.3 IPv6 Configuration
        • 9.2.2.3.1 Commands for IPv6 configuration
          • 9.2.2.3.1.1 ipv6 enable
          • 9.2.2.3.1.2 ipv6 address
          • 9.2.2.3.1.3 ipv6 route
          • 9.2.2.3.1.4 ipv6 nd dad attempts
          • 9.2.2.3.1.5 ipv6 nd ns-interval
          • 9.2.2.3.1.6 ipv6 nd suppress-ra
          • 9.2.2.3.1.7 ipv6 nd ra-lifetime
          • 9.2.2.3.1.8 ipv6 nd min-ra-interval
          • 9.2.2.3.1.9 ipv6 nd max-ra-interval
          • 9.2.2.3.1.10 ipv6 nd prefix
          • 9.2.2.3.1.11 ipv6 nd prefix
          • 9.2.2.3.1.12 ipv6 neighbor
          • 9.2.2.3.1.13 interface tunnel
          • 9.2.2.3.1.14 ping6
          • 9.2.2.3.1.15 tunnel source
          • 9.2.2.3.1.16 tunnel destination
          • 9.2.2.3.1.17 tunnel nexthop
          • 9.2.2.3.1.18 tunnel 6to4-relay
          • 9.2.2.3.1.19 tunnel mode
          • 9.2.2.3.1.20 clear ipv6 neighbor
    • 9.2.3 IP Configuration Examples
      • 9.2.3.1 Configuration Examples of IPv4
      • 9.2.3.2 Configuration Examples of IPv6
    • 9.2.4 IP Troubleshooting
      • 9.2.4.1 Commands for Monitor And Debug
        • 9.2.4.1.1 show ip traffic
        • 9.2.4.1.2 debug ip packet
        • 9.2.4.1.3 debug ipv6 packet
        • 9.2.4.1.4 debug ipv6 icmp
        • 9.2.4.1.5 debug ipv6 nd
        • 9.2.4.1.6 debug ipv6 tunnel packet
        • 9.2.4.1.7 show ipv6 interface
        • 9.2.4.1.8 show ipv6 route
        • 9.2.4.1.9 show ipv6 neighbors
        • 9.2.4.1.10 show ipv6 traffic
        • 9.2.4.1.11 show ipv6 enable
        • 9.2.4.1.12 show ipv6 tunnel
  • 9.3 IP Forwarding
    • 9.3.1 Introduction to IP Forwarding
    • 9.3.2 IP Route Aggregation Configuration Task
    • 9.3.3 Commands for IP Route Aggregation
      • 9.3.3.1 ip fib optimize
  • 9.4 URPF
    • 9.4.1 URPF Introduction
    • 9.4.2 URPF Operation Mechanism
    • 9.4.3 URPF Configuration Task Sequence
    • 9.4.4 Commands For URPF
      • 9.4.4.1 urpf enable
      • 9.4.4.2 show urpf
      • 9.4.4.3 show urpf interface
      • 9.4.4.4 debug urpf
    • 9.4.5 URPF Troubleshooting
  • 9.5 ARP
    • 9.5.1 Introduction to ARP
    • 9.5.2 ARP Configuration Task List
    • 9.5.3 Commands for ARP Configuration
      • 9.5.3.1 Arp
      • 9.5.3.2 clear arp-cache
      • 9.5.3.3 ip proxy-arp
      • 9.5.3.4 ARP Troubleshooting
        • 9.5.3.4.1 Commands for Monitor And Debug
          • 9.5.3.4.1.1 debug arp
          • 9.5.3.4.1.2 show arp
• Chapter 10 DHCP Configuration
  • 10.1 Introduction to DHCP
  • 10.2 DHCP Server Configuration
    • 10.2.1 DHCP Sever Configuration Task List
    • 10.2.2 Commands for DHCP Server Configuration
      • 10.2.2.1 bootfile
      • 10.2.2.2 client-identifier
      • 10.2.2.3 client-name
      • 10.2.2.4 default-router
      • 10.2.2.5 dns-server
      • 10.2.2.6 domain-name
      • 10.2.2.7 hardware-address
      • 10.2.2.8 host
      • 10.2.2.9 ip dhcp conflict logging
      • 10.2.2.10 ip dhcp excluded-address
      • 10.2.2.11 ip dhcp pool
      • 10.2.2.12 loghost dhcp
      • 10.2.2.13 lease
      • 10.2.2.14 netbios-name-server
      • 10.2.2.15 netbios-node-type
      • 10.2.2.16 network-address
      • 10.2.2.17 next-server
      • 10.2.2.18 option
      • 10.2.2.19 service dhcp
  • 10.3 DHCP Relay Configuration
    • 10.3.1 DHCP Relay Configuration Task List
    • 10.3.2 Commands for DHCP Relay Configuration
      • 10.3.2.1 clear ip dhcp binding
      • 10.3.2.2 clear ip dhcp conflict
      • 10.3.2.3 clear ip dhcp server statistics
      • 10.3.2.4 debug ip dhcp server
      • 10.3.2.5 ip forward-protocol udp
      • 10.3.2.6 ip helper-address
      • 10.3.2.7 ip dhcp relay information policy drop
  • 10.4 DHCP Configuration Example
  • 10.5 DHCP Troubleshooting
    • 10.5.1 Commands for Monitor and Debug
      • 10.5.1.1 show ip dhcp binding
      • 10.5.1.2 show ip dhcp conflict
      • 10.5.1.3 show ip dhcp server statistics
  • 10.6 Web Management
    • 10.6.1 DHCP server configuration
      • 10.6.1.1 Enable DHCP
      • 10.6.1.2 Address pool configuration
      • 10.6.1.3 Client's default gateway configuration
      • 10.6.1.4 Client DNS server configuration
      • 10.6.1.5 Client WINS server configuration
      • 10.6.1.6 DHCP file server address configuration
      • 10.6.1.7 DHCP network parameter configuration
      • 10.6.1.8 Manual address pool configuration
      • 10.6.1.9 Excluded address
      • 10.6.1.10 DHCP packet statistics
      • 10.6.1.11 DHCP relay configuration
    • 10.6.2 DHCP debugging
      • 10.6.2.1 Delete binding log
      • 10.6.2.2 Delete conflict log
      • 10.6.2.3 Delete DHCP server statistics log
      • 10.6.2.4 Show IP-MAC binding
      • 10.6.2.5 Show conflict-logging
• Chapter 11 SNTP Configuration
  • 11.1 Introduction to SNTP
  • 11.2 Commands for SNTP
    • 11.2.1 sntp server
    • 11.2.2 sntp poll
    • 11.2.3 debug sntp
    • 11.2.4 show sntp
  • 11.3 Typical SNTP Configuration Examples
  • 11.4 Web Management
    • 11.4.1 SNMP/NTP server configuration
    • 11.4.2 Request interval configuration
    • 11.4.3 Time difference
    • 11.4.4 Show SNTP
• Chapter 12 Prevent ARP, ND Spoofing Configuration
  • 12.1 Overview
    • 12.1.1 ARP ( Address Resolution Protocol)
    • 12.1.2 ARP Spoofing
    • 12.1.3 How to prevent void ARP/ND Spoofing for our Layer 3 Switch
  • 12.2 Prevent ARP, ND Spoofing configuration
    • 12.2.1 Prevent ARP, ND Spoofing Configuration Task List
  • 12.3 Commands For Preventing ARP, ND Spoofing
    • 12.3.1 ip arp-security updateprotect
    • 12.3.2 ipv6 nd-security updateprotect
    • 12.3.3 ip arp-security learnprotect
    • 12.3.4 ipv6 nd learnprotect
    • 12.3.5 ip arp-security convert
    • 12.3.6 ipv6 nd-security convert
    • 12.3.7 clear ip arp dynamic
    • 12.3.8 clear ipv6 nd dynamic
  • 12.4 Prevent ARP, ND Spoofing Example
• Chapter 13 Routing Protocol
  • 13.1 Routing Protocol Overview
    • 13.1.1 Routing Table
  • 13.2 IP Routing Policy
    • 13.2.1 Introduction To Routing Policy
    • 13.2.2 IP Routing Policy Configuration Task List
    • 13.2.3 Commands for Routing Policy
      • 13.2.3.1 ip prefix-list description
      • 13.2.3.2 ip prefix-list seq
      • 13.2.3.3 match as-path
      • 13.2.3.4 match community
      • 13.2.3.5 match interface
      • 13.2.3.6 match ip
      • 13.2.3.7 match metric
      • 13.2.3.8 match origin
      • 13.2.3.9 match route-type
      • 13.2.3.10 match tag
      • 13.2.3.11 route-map
      • 13.2.3.12 set aggregator
      • 13.2.3.13 set as-path
      • 13.2.3.14 set atomic-aggregate
      • 13.2.3.15 set comm-list
      • 13.2.3.16 set community
      • 13.2.3.17 set extcommunity
      • 13.2.3.18 set ip next-hop
      • 13.2.3.19 set local-preference
      • 13.2.3.20 set metric
      • 13.2.3.21 set metric-type
      • 13.2.3.22 set origin
      • 13.2.3.23 set originator-id
      • 13.2.3.24 set tag
      • 13.2.3.25 set vpnv4 next-hop
      • 13.2.3.26 set weight
    • 13.2.4 Configuration Examples
    • 13.2.5 Troubleshooting
      • 13.2.5.1 Monitor And Debug Command
        • 13.2.5.1.1 show ip prefix-list <list-name>
        • 13.2.5.1.2 show ip prefix-list <detail | summary>
        • 13.2.5.1.3 show route-map
  • 13.3 Static Route
    • 13.3.1 Introduction to Static Route
    • 13.3.2 Introduction to Default Route
    • 13.3.3 Static Route Configuration Task List
    • 13.3.4 Commands for Static Route
      • 13.3.4.1 ip route
      • 13.3.4.2 show ip route
      • 13.3.4.3 show ip route fib
      • 13.3.4.4 show ip route vrf
      • 13.3.4.5 ip route vrf
    • 13.3.5 Configuration Examples
  • 13.4 RIP
    • 13.4.1 Introduction to RIP
    • 13.4.2 RIP Configuration Task List
    • 13.4.3 Commands for RIP
      • 13.4.3.1 accept-lifetime
      • 13.4.3.2 address-family ipv4
      • 13.4.3.3 clear ip rip route
      • 13.4.3.4 debug rip
      • 13.4.3.5 default-information originate
      • 13.4.3.6 default-metric
      • 13.4.3.7 distance
      • 13.4.3.8 distribute-list
      • 13.4.3.9 exit-address-family
      • 13.4.3.10 ip rip authentication key
      • 13.4.3.11 ip rip authentication mode
      • 13.4.3.12 ip rip authentication string
      • 13.4.3.13 ip rip authentication cisco-compatible
      • 13.4.3.14 ip rip receive-packet
      • 13.4.3.15 ip rip receive version
      • 13.4.3.16 ip rip send-packet
      • 13.4.3.17 ip rip send version
      • 13.4.3.18 ip rip split-horizon
      • 13.4.3.19 key
      • 13.4.3.20 key chain
      • 13.4.3.21 key-string
      • 13.4.3.22 maximum-prefix
      • 13.4.3.23 neighbor
      • 13.4.3.24 network
      • 13.4.3.25 offset-list
      • 13.4.3.26 passive-interface
      • 13.4.3.27 recv-buffer-size
      • 13.4.3.28 redistribute
      • 13.4.3.29 route
      • 13.4.3.30 router rip
      • 13.4.3.31 send-lifetime
      • 13.4.3.32 timers basic
      • 13.4.3.33 version
    • 13.4.4 RIP Examples
      • 13.4.4.1 Typical RIP Examples
      • 13.4.4.2 Configuration Examples of RIP VPN
    • 13.4.5 RIP Troubleshooting
      • 13.4.5.1 Commands for Monitor And Debug
        • 13.4.5.1.1 show debugging rip
        • 13.4.5.1.2 show ip protocols rip
        • 13.4.5.1.3 show ip rip
        • 13.4.5.1.4 show ip rip database
        • 13.4.5.1.5 show ip rip database vrf
        • 13.4.5.1.6 show ip rip interface
        • 13.4.5.1.7 show ip rip interface vrf
        • 13.4.5.1.8 show ip vrf
  • 13.5 RIPng
    • 13.5.1 Introduction to RIPng
    • 13.5.2 RIPng Configuration Task List
    • 13.5.3 Commands For RIPng
      • 13.5.3.1 aggregate-address
      • 13.5.3.2 clear ipv6 route
      • 13.5.3.3 default-information originate
      • 13.5.3.4 default-metric
      • 13.5.3.5 ipv6 rip split-horizon
      • 13.5.3.6 distribute-list
      • 13.5.3.7 ipv6 router rip
      • 13.5.3.8 neighbor
      • 13.5.3.9 Offset-list
      • 13.5.3.10 passive-interface
      • 13.5.3.11 redistribute
      • 13.5.3.12 route
      • 13.5.3.13 router ipv6 rip
    • 13.5.4 RIPng Configuration Examples
    • 13.5.5 RIPng Troubleshooting
      • 13.5.5.1 Commands for Monitor And Debug Commands
        • 13.5.5.1.1 debug ipv6 rip
        • 13.5.5.1.2 show debugging ipv6 rip
        • 13.5.5.1.3 show ipv6 rip interface
        • 13.5.5.1.4 show ipv6 protocols rip
        • 13.5.5.1.5 show ipv6 rip
        • 13.5.5.1.6 show ipv6 rip database
        • 13.5.5.1.7 show ipv6 rip interface
  • 13.6 OSPF
    • 13.6.1 Introduction to OSPF
    • 13.6.2 OSPF Configuration Task List
    • 13.6.3 Commands for OSPF
      • 13.6.3.1 area authentication
      • 13.6.3.2 area default cost
      • 13.6.3.3 area filter-list
      • 13.6.3.4 area nssa
      • 13.6.3.5 area range
      • 13.6.3.6 area shortcut
      • 13.6.3.7 area stub
      • 13.6.3.8 area virtual-link
      • 13.6.3.9 auto-cost reference-bandwidth
      • 13.6.3.10 capability opaque
      • 13.6.3.11 compatible rfc1583
      • 13.6.3.12 clear ip ospf process
      • 13.6.3.13 distance
      • 13.6.3.14 distribute-list
      • 13.6.3.15 host area
      • 13.6.3.16 ip ospf authentication
      • 13.6.3.17 ip ospf authentication-key
      • 13.6.3.18 ip ospf cost
      • 13.6.3.19 ip ospf database-filter
      • 13.6.3.20 ip ospf dead-interval
      • 13.6.3.21 ip ospf disable all
      • 13.6.3.22 ip ospf hello-interval
      • 13.6.3.23 ip ospf message-digest-key
      • 13.6.3.24 ip ospf mtu
      • 13.6.3.25 ip ospf mtu-ignore
      • 13.6.3.26 ip ospf network
      • 13.6.3.27 ip ospf priority
      • 13.6.3.28 ip ospf retransmit-interval
      • 13.6.3.29 ip ospf transmit-delay
      • 13.6.3.30 max-concurrent-dd
      • 13.6.3.31 neighbor
      • 13.6.3.32 network area
      • 13.6.3.33 ospf abr-type
      • 13.6.3.34 ospf router-id
      • 13.6.3.35 overflow database
      • 13.6.3.36 overflow database external
      • 13.6.3.37 passive-interface
      • 13.6.3.38 redistribute
      • 13.6.3.39 router ospf
      • 13.6.3.40 default-information originate
      • 13.6.3.41 default-metric
      • 13.6.3.42 summary-address
      • 13.6.3.43 timers spf
    • 13.6.4 OSPF Example
      • 13.6.4.1 Configuration Example of OSPF
      • 13.6.4.2 Configuration Examples of OSPF VPN
    • 13.6.5 OSPF Troubleshooting
      • 13.6.5.1 Commands for Monitor And Debug
        • 13.6.5.1.1 debug ospf events
        • 13.6.5.1.2 debug ospf ifsm
        • 13.6.5.1.3 debug ospf lsa
        • 13.6.5.1.4 debug ospf nfsm
        • 13.6.5.1.5 debug ospf nsm
        • 13.6.5.1.6 debug ospf packet
        • 13.6.5.1.7 debug ospf route
        • 13.6.5.1.8 show ip ospf
        • 13.6.5.1.9 show ip ospf border-routers
        • 13.6.5.1.10 show ip ospf database
        • 13.6.5.1.11 show ip ospf interface
        • 13.6.5.1.12 show ip ospf neighbor
        • 13.6.5.1.13 show ip ospf route
        • 13.6.5.1.14 show ip ospf virtual-links
        • 13.6.5.1.15 show ip protocols
  • 13.7 OSPFv3
    • 13.7.1 Introduction to OSPFv3
    • 13.7.2 OSPFv3 Configuration Task List
    • 13.7.3 Commands for OSPFV3
      • 13.7.3.1 area default cost
      • 13.7.3.2 area range
      • 13.7.3.3 area stub
      • 13.7.3.4 area virtual-link
      • 13.7.3.5 abr-type
      • 13.7.3.6 default-metric
      • 13.7.3.7 ipv6 ospf cost
      • 13.7.3.8 ipv6 ospf dead-interval
      • 13.7.3.9 ipv6 ospf display route single-line
      • 13.7.3.10 ipv6 ospf hello-interval
      • 13.7.3.11 ipv6 ospf priority
      • 13.7.3.12 ipv6 ospf retransmit-interval
      • 13.7.3.13 ipv6 ospf transmit-delay
      • 13.7.3.14 ipv6 router ospf
      • 13.7.3.15 max-concurrent-dd
      • 13.7.3.16 passive-interface
      • 13.7.3.17 redistribute
      • 13.7.3.18 router-id
      • 13.7.3.19 router ipv6 ospf
      • 13.7.3.20 timers spf
    • 13.7.4 OSPFv3 Examples
    • 13.7.5 OSPFv3 Troubleshooting
      • 13.7.5.1 Commands for Monitor And Debug
        • 13.7.5.1.1 debug ipv6 ospf ifsm
        • 13.7.5.1.2 debug ipv6 ospf lsa
        • 13.7.5.1.3 debug ipv6 ospf nfsm
        • 13.7.5.1.4 debug ipv6 ospf nsm
        • 13.7.5.1.5 debug ipv6 ospf packet
        • 13.7.5.1.6 debug ipv6 ospf route
        • 13.7.5.1.7 show ipv6 ospf
        • 13.7.5.1.8 show ipv6 ospf database
        • 13.7.5.1.9 show ipv6 ospf interface
        • 13.7.5.1.10 show ipv6 ospf neighbor
        • 13.7.5.1.11 show ipv6 ospf route
        • 13.7.5.1.12 show ipv6 ospf topology
        • 13.7.5.1.13 show ipv6 ospf virtual-links
  • 13.8 BGP
    • 13.8.1 BGP Introduction
    • 13.8.2 BGP Configuration Task List
    • 13.8.3 Commands for BGP
      • 13.8.3.1 address-family
      • 13.8.3.2 address-family ipv4
      • 13.8.3.3 address-family vpnv4
      • 13.8.3.4 aggregate-address
      • 13.8.3.5 bgp aggregate-nexthop-check
      • 13.8.3.6 bgp always-compare-med
      • 13.8.3.7 bgp bestpath as-path ignore
      • 13.8.3.8 bgp bestpath compare-confed-aspath
      • 13.8.3.9 bgp bestpath compare-routerid
      • 13.8.3.10 bgp bestpath med
      • 13.8.3.11 bgp client-to-client reflection
      • 13.8.3.12 bgp cluster-id
      • 13.8.3.13 bgp confederation identifier
      • 13.8.3.14 bgp confederation peers
      • 13.8.3.15 bgp dampening
      • 13.8.3.16 bgp default
      • 13.8.3.17 bgp deterministic-med
      • 13.8.3.18 bgp enforce-first-as
      • 13.8.3.19 bgp fast-external-failover
      • 13.8.3.20 bgp inbound-route-filter
      • 13.8.3.21 bgp log-neighbor-changes
      • 13.8.3.22 bgp multiple-instance
      • 13.8.3.23 bgp network import-check
      • 13.8.3.24 bgp rfc1771-path-select
      • 13.8.3.25 bgp rfc1771-strict
      • 13.8.3.26 bgp router-id
      • 13.8.3.27 bgp scan-time
      • 13.8.3.28 clear ip bgp
      • 13.8.3.29 clear ip bgp dampening
      • 13.8.3.30 clear ip bgp flap-statistics
      • 13.8.3.31 distance
      • 13.8.3.32 distance bgp
      • 13.8.3.33 exit-address-family
      • 13.8.3.34 import map
      • 13.8.3.35 ip as-path access-list
      • 13.8.3.36 ip community-list
      • 13.8.3.37 ip extcommunity-list
      • 13.8.3.38 label-switching
      • 13.8.3.39 mpls enable-all-interfaces
      • 13.8.3.40 mpls disable-all-interfaces
      • 13.8.3.41 neighbor activate
      • 13.8.3.42 neighbor advertisement-interval
      • 13.8.3.43 neighbor allowas-in
      • 13.8.3.44 neighbor attribute-unchanged
      • 13.8.3.45 neighbor as-override
      • 13.8.3.46 neighbor capability
      • 13.8.3.47 neighbor capability orf prefix-list
      • 13.8.3.48 neighbor collide-established
      • 13.8.3.49 neighbor default-originate
      • 13.8.3.50 neighbor description
      • 13.8.3.51 neighbor distribute-list
      • 13.8.3.52 neighbor dont-capability-negotiate
      • 13.8.3.53 neighbor ebgp-multihop
      • 13.8.3.54 neighbor enforce-multihop
      • 13.8.3.55 neighbor filter-list
      • 13.8.3.56 neighbor interface
      • 13.8.3.57 neighbor maximum-prefix
      • 13.8.3.58 neighbor next-hop-self
      • 13.8.3.59 neighbor override-capability
      • 13.8.3.60 neighbor passive
      • 13.8.3.61 neighbor peer-group （Creating）
      • 13.8.3.62 neighbor peer-group （Configuring group members）
      • 13.8.3.63 neighbor port
      • 13.8.3.64 neighbor prefix-list
      • 13.8.3.65 neighbor remote-as
      • 13.8.3.66 neighbor remove-private-AS
      • 13.8.3.67 neighbor route-map
      • 13.8.3.68 neighbor route-reflector-client
      • 13.8.3.69 neighbor route-server-client
      • 13.8.3.70 neighbor send-community
      • 13.8.3.71 neighbor shutdown
      • 13.8.3.72 neighbor soft-reconfiguration inbound
      • 13.8.3.73 neighbor soo
      • 13.8.3.74 neighbor strict-capability-match
      • 13.8.3.75 neighbor timers
      • 13.8.3.76 neighbor timers connect
      • 13.8.3.77 neighbor unsuppress-map
      • 13.8.3.78 neighbor update-source
      • 13.8.3.79 neighbor version 4
      • 13.8.3.80 neighbor weight
      • 13.8.3.81 network (BGP)
      • 13.8.3.82 redistribute (BGP)
      • 13.8.3.83 rd
      • 13.8.3.84 router bgp
      • 13.8.3.85 route-target
      • 13.8.3.86 set vpnv4 next-hop
      • 13.8.3.87 timers bgp
    • 13.8.4 Configuration Examples of BGP
      • 13.8.4.1 Examples 1: configure BGP neighbor
      • 13.8.4.2 Examples 2: configure BGP aggregation
      • 13.8.4.3 Examples 3: configure BGP community attributes
      • 13.8.4.4 Examples 4: configure BGP confederation
      • 13.8.4.5 Examples 5: configure BGP route reflector
      • 13.8.4.6 Examples 6: configure MED of BGP
      • 13.8.4.7 Examples 7: BGP VPN Typical samples of BGP VPN
    • 13.8.5 BGP Troubleshooting
      • 13.8.5.1 Commands for Monitor And Debug
        • 13.8.5.1.1 show ip bgp
        • 13.8.5.1.2 show ip bgp attribute-info
        • 13.8.5.1.3 show ip bgp community
        • 13.8.5.1.4 show ip bgp community-info
        • 13.8.5.1.5 show ip bgp community-list
        • 13.8.5.1.6 show ip bgp dampening
        • 13.8.5.1.7 show ip bgp filter-list
        • 13.8.5.1.8 show ip bgp inconsistent-as
        • 13.8.5.1.9 show ip bgp neighbors
        • 13.8.5.1.10 show ip bgp paths
        • 13.8.5.1.11 show ip bgp prefix-list
        • 13.8.5.1.12 show ip bgp quote-regexp
        • 13.8.5.1.13 show ip bgp regexp
        • 13.8.5.1.14 show ip bgp route-map
        • 13.8.5.1.15 show ip bgp scan
        • 13.8.5.1.16 show ip bgp summary
        • 13.8.5.1.17 show ip bgp view
        • 13.8.5.1.18 show ip bgp view neighbors
        • 13.8.5.1.19 show ip bgp vpnv4
        • 13.8.5.1.20 debug bgp
  • 13.9 MBGP4+
    • 13.9.1 MBGP4+ Introduction
    • 13.9.2 MBGP4+ Configures Mission List
    • 13.9.3 MBGP4+ Examples
    • 13.9.4 MBGP4+ Troubleshooting
• Chapter 14 IGMP Snooping
  • 14.1 Introduction to IGMP Snooping
  • 14.2 IGMP Snooping Configuration Task
  • 14.3 Commands for IGMP Snooping
    • 14.3.1 ip igmp snooping vlan
    • 14.3.2 ip igmp snooping vlan immediate-leave
    • 14.3.3 ip igmp snooping vlan l2-general-querier
    • 14.3.4 ip igmp snooping vlan limit
    • 14.3.5 ip igmp snooping vlan mrouter-port interface
    • 14.3.6 ip igmp snooping vlan mrpt
    • 14.3.7 ip igmp snooping vlan query-interval
    • 14.3.8 ip igmp snooping vlan query-mrsp
    • 14.3.9 ip igmp snooping vlan query-robustness
    • 14.3.10 ip igmp snooping vlan suppression-query-time
  • 14.4 IGMP Snooping Example
  • 14.5 IGMP Snooping Troubleshooting
    • 14.5.1 Commands for Monitor And Debug
      • 14.5.1.1 debug ip igmp snooping
      • 14.5.1.2 debug igmp snooping all/packet/event/timer/mfc
      • 14.5.1.3 show ip igmp snooping
      • 14.5.1.4 show mac-address-table multicast
• Chapter 15 Multicast VLAN
  • 15.1 Introductions To Multicast VLAN
  • 15.2 Multicast VLAN Configuration Task
  • 15.3 Commands For Multicast VLAN
    • 15.3.1 multicast-vlan
    • 15.3.2 multicast-vlan association<vlan-list>
  • Examples Of Multicast VLAN
• Chapter 16 IPv4 Multicast Protocol
  • 16.1 IPv4 Multicast Protocol Overview
    • 16.1.1 Introduction to Multicast
    • 16.1.2 Multicast Address
    • 16.1.3 IP Multicast Packet Transmission
    • 16.1.4 IP Multicast Application
  • 16.2 PIM-DM
    • 16.2.1 Introduction to PIM-DM
    • 16.2.2 PIM-DM Configuration Task List
    • 16.2.3 Commands for PIM-DM
      • 16.2.3.1 ip pim dense-mode
      • 16.2.3.2 ip pim hello-interval
      • 16.2.3.3 ip pim state-refresh origination-interval
    • 16.2.4 PIM-DM Configuration Examples
    • 16.2.5 PIM-DM Troubleshooting
      • 16.2.5.1 commands for Monitor and debug
        • 16.2.5.1.1 debug pim timer sat
        • 16.2.5.1.2 debug pim timer srt
        • 16.2.5.1.3 show ip pim mroute dense-mode
  • 16.3 PIM-SM
    • 16.3.1 Introduction to PIM-SM
    • 16.3.2 PIM-SM Configuration Task List
    • 16.3.3 Commands for PIM-SM
      • 16.3.3.1 ip pim accept-register
      • 16.3.3.2 ip pim bsr-candidate
      • 16.3.3.3 ip pim cisco-register-checksum
      • 16.3.3.4 ip pim dr-priority
      • 16.3.3.5 ip pim exclude-genid
      • 16.3.3.6 ip pim hello-holdtime
      • 16.3.3.7 ip pim hello-interval
      • 16.3.3.8 ip pim ignore-rp-set-priority
      • 16.3.3.9 ip pim jp-timer
      • 16.3.3.10 ip pim multicast-routing
      • 16.3.3.11 ip pim neighbor-filter
      • 16.3.3.12 ip pim register-rate-limit
      • 16.3.3.13 ip pim register-rp-reachability
      • 16.3.3.14 ip pim register-source
      • 16.3.3.15 ip pim register-suppression
      • 16.3.3.16 ip pim rp-address
      • 16.3.3.17 ip pim rp-candidate
      • 16.3.3.18 ip pim rp-register-kat
      • 16.3.3.19 ip pim sparse-mode
      • 16.3.3.20 ip pim ssm
    • 16.3.4 PIM-SM Configuration Examples
    • 16.3.5 PIM-SM Troubleshooting
      • 16.3.5.1 Commands for Monitor And Debug
        • 16.3.5.1.1 debug pim event
        • 16.3.5.1.2 debug pim mfc
        • 16.3.5.1.3 debug pim mib
        • 16.3.5.1.4 debug pim nexthop
        • 16.3.5.1.5 debug pim nsm
        • 16.3.5.1.6 debug pim packet
        • 16.3.5.1.7 debug pim state
        • 16.3.5.1.8 debug pim timer
        • 16.3.5.1.9 show ip pim bsr-router
        • 16.3.5.1.10 show ip pim interface
        • 16.3.5.1.11 show ip pim mroute sparse-mode
        • 16.3.5.1.12 show ip pim neighbor
        • 16.3.5.1.13 show ip pim nexthop
        • 16.3.5.1.14 show ip pim rp-hash
        • 16.3.5.1.15 show ip pim rp mapping
  • 16.4 DVMRP
    • 16.4.1 Introduction to DVMRP
    • 16.4.2 Configuration Task List
    • 16.4.3 Commands for DVMRP
      • 16.4.3.1 ip dvmrp
      • 16.4.3.2 ip dvmrp metric
      • 16.4.3.3 ip dvmrp multicast-routing
      • 16.4.3.4 ip dvmrp output-report-delay
      • 16.4.3.5 ip dvmrp reject-non-pruners
      • 16.4.3.6 ip dvmrp tunnel
    • 16.4.4 DVMRP Configuration Examples
    • 16.4.5 DVMRP Troubleshooting
      • 16.4.5.1 Commands for Monitor And Debug
        • 16.4.5.1.1 debug dvmrp
        • 16.4.5.1.2 show ip dvmrp
        • 16.4.5.1.3 show ip dvmrp interface
        • 16.4.5.1.4 show ip dvmrp neighbor
        • 16.4.5.1.5 show ip dvmrp pr
        • 16.4.5.1.6 show ip dvmrp route
  • 16.5 ECSCM
    • 16.5.1 Introduction to ECSCM
    • 16.5.2 ECSCM Configuration Task List
    • 16.5.3 Commands for ECSCM
      • 16.5.3.1 access-list (Multicast Source Control)
      • 16.5.3.2 access-list (Multicast Destination Control)
      • 16.5.3.3 ip multicast destination-control access-group
      • 16.5.3.4 ip multicast destination-control access-group (vmac)
      • 16.5.3.5 ip multicast destination-control access-group (sip)
      • 16.5.3.6 ip multicast destination-control
      • 16.5.3.7 ip multicast policy
      • 16.5.3.8 ip multicast source-control
      • 16.5.3.9 ip multicast source-control access-group
    • 16.5.4 ECSCM Configuration Examples
    • 16.5.5 ECSCM Troubleshooting
      • 16.5.5.1 Monitor And Debug
        • 16.5.5.1.1 show ip multicast destination-control
        • 16.5.5.1.2 show ip multicast destination-control access-list
        • 16.5.5.1.3 show ip multicast policy
        • 16.5.5.1.4 show ip multicast source-control
        • 16.5.5.1.5 show ip multicast source-control access-list
  • 16.6 IGMP
    • 16.6.1 Introduction to IGMP
    • 16.6.2 Configuration Task List
    • 16.6.3 Commands for IGMP
      • 16.6.3.1 ip igmp access-group
      • 16.6.3.2 ip igmp immediate-leave
      • 16.6.3.3 ip igmp last-member-query-interval
      • 16.6.3.4 ip igmp limit
      • 16.6.3.5 ip igmp join-group
      • 16.6.3.6 ip igmp query-interval
      • 16.6.3.7 ip igmp query-max-response-time
      • 16.6.3.8 ip igmp query-timeout
      • 16.6.3.9 ip igmp static-group
      • 16.6.3.10 ip igmp version
    • 16.6.4 IGMP Configuration Example
    • 16.6.5 IGMP Troubleshooting
      • 16.6.5.1 Commands for Monitor and debug
        • 16.6.5.1.1 debug igmp event
        • 16.6.5.1.2 debug igmp packet
        • 16.6.5.1.3 show ip igmp groups
        • 16.6.5.1.4 show ip igmp interface
• Chapter 17 IPv6 Multicast Protocol
  • 17.1 PIM-DM6
    • 17.1.1 Introduction to PIM-DM6
    • 17.1.2 PIM-DM Configuration Task List
    • 17.1.3 Commands for PIM-DM6
      • 17.1.3.1 ipv6 pim dense-mode
      • 17.1.3.2 ipv6 pim dr-priority
      • 17.1.3.3 ipv6 pim exclude-genid
      • 17.1.3.4 ipv6 pim hello-holdtime
      • 17.1.3.5 ipv6 pim hello-interval
      • 17.1.3.6 ipv6 pim multicast-routing
      • 17.1.3.7 ipv6 pim neighbor-filter
      • 17.1.3.8 ipv6 pim state-refresh origination-interval
    • 17.1.4 PIM-DM Typical Application
    • 17.1.5 PIM-DM Troubleshooting
      • 17.1.5.1 Command for Monitor and debug
        • 17.1.5.1.1 debug ipv6 pim timer sat
        • 17.1.5.1.2 debug ipv6 pim timer srt
        • 17.1.5.1.3 show ipv6 pim mroute dense-mode
  • 17.2 PIM-SM6
    • 17.2.1 Introduction to PIM-SM6
    • 17.2.2 PIM-SM Configuration Task List
    • 17.2.3 Commands for PIM-SM
      • 17.2.3.1 ipv6 pim accept-register
      • 17.2.3.2 ipv6 pim bsr-candidate
      • 17.2.3.3 ipv6 pim cisco-register-checksum
      • 17.2.3.4 ipv6 pim dr-priority
      • 17.2.3.5 ipv6 pim exclude-genid
      • 17.2.3.6 ipv6 pim hello-holdtime
      • 17.2.3.7 ipv6 pim hello-interval
      • 17.2.3.8 ipv6 pim ignore-rp-set-priority
      • 17.2.3.9 ipv6 pim jp-timer
      • 17.2.3.10 ipv6 pim multicast-routing
      • 17.2.3.11 ipv6 pim neighbor-filter
      • 17.2.3.12 ipv6 pim register-rate-limit
      • 17.2.3.13 ipv6 pim register-rp-reachability
      • 17.2.3.14 ipv6 pim register-source
      • 17.2.3.15 ipv6 pim register-suppression
      • 17.2.3.16 ipv6 pim rp-address
      • 17.2.3.17 ipv6 pim rp-candidate
      • 17.2.3.18 ipv6 pim rp-register-kat
      • 17.2.3.19 ipv6 pim sparse-mode
    • 17.2.4 PIM-SM Typical Application
    • 17.2.5 PIM-SM Troubleshooting
      • 17.2.5.1 Command for Monitor and debug
        • 17.2.5.1.1 debug ipv6 pim events
        • 17.2.5.1.2 debug ipv6 pim mfc
        • 17.2.5.1.3 debug ipv6 pim mib
        • 17.2.5.1.4 debug ipv6 pim nexthop
        • 17.2.5.1.5 debug ipv6 pim nsm
        • 17.2.5.1.6 debug ipv6 pim packet
        • 17.2.5.1.7 debug ipv6 pim state
        • 17.2.5.1.8 debug ipv6 pim timer
        • 17.2.5.1.9 show ipv6 pim bsr-router
        • 17.2.5.1.10 show ipv6 pim interface
        • 17.2.5.1.11 show ipv6 pim mroute sparse-mode
        • 17.2.5.1.12 show ipv6 pim neighbor
        • 17.2.5.1.13 show ipv6 pim nexthop
        • 17.2.5.1.14 show ipv6 pim rp-hash
        • 17.2.5.1.15 show ipv6 pim rp mapping
  • 17.3 MLD
    • 17.3.1 Introduction to MLD
    • 17.3.2 MLD Configuration Task List
    • 17.3.3 Commands for MLD
      • 17.3.3.1 ipv6 mld access-group
      • 17.3.3.2 ipv6 mld immediate-leave
      • 17.3.3.3 ipv6 mld last-member-query-interval
      • 17.3.3.4 ipv6 mld query-interval
      • 17.3.3.5 ipv6 mld query-max-response-time
      • 17.3.3.6 ipv6 mld query-timeout
      • 17.3.3.7 ipv6 mld access-group
      • 17.3.3.8 ipv6 mld join-group
      • 17.3.3.9 ipv6 mld join-group mode source
      • 17.3.3.10 ipv6 mld limit
      • 17.3.3.11 ipv6 mld static-group
      • 17.3.3.12 ipv6 mld version
    • 17.3.4 MLD Typical Application
    • 17.3.5 MLD Troubleshooting
      • 17.3.5.1 Command for Monitor And Debug
        • 17.3.5.1.1 debug ipv6 mld events
        • 17.3.5.1.2 debug ipv6 mld packet
        • 17.3.5.1.3 show ipv6 mld groups
        • 17.3.5.1.4 show ipv6 mld interface
  • 17.4 MLD Snooping
    • 17.4.1 MLD Snooping Introduction
    • 17.4.2 MLD Snooping Configuration Task
    • 17.4.3 Commands For MLD Snooping Configuration
      • 17.4.3.1 debug mld snooping all/packet/event/timer/mfc
      • 17.4.3.2 ipv6 mld snooping
      • 17.4.3.3 ipv6 mld snooping vlan
      • 17.4.3.4 ipv6 mld snooping vlan immediate-leave
      • 17.4.3.5 ipv6 mld snooping vlan l2-general-querier
      • 17.4.3.6 ipv6 mld snooping vlan limit
      • 17.4.3.7 ipv6 mld snooping vlan mrouter-port interface
      • 17.4.3.8 ipv6 mld snooping vlan mrpt
      • 17.4.3.9 ipv6 mld snooping vlan query-interval
      • 17.4.3.10 ipv6 mld snooping vlan query-mrsp
      • 17.4.3.11 ipv6 mld snooping vlan query-robustness
      • 17.4.3.12 ipv6 mld snooping vlan suppression-query-time
      • 17.4.3.13 show ipv6 mld snooping
      • 17.4.3.14 show mac-address-table multicast
    • 17.4.4 MLD Snooping Examples
    • 17.4.5 MLD Snooping Troubleshooting
• Chapter 18 ACL Configuration
  • 18.1 Introduction to ACL
    • 18.1.1 Access-list
    • 18.1.2 Access-group
    • 18.1.3 Access-list Action and Global Default Action
  • 18.2 ACL Configuration
    • 18.2.1 ACL Configuration Task Sequence
    • 18.2.2 Commands for ACL
      • 18.2.2.1 absolute-periodic/periodic
      • 18.2.2.2 absolute start
      • 18.2.2.3 access-list(ip extended)
      • 18.2.2.4 access-list(ip standard)
      • 18.2.2.5 access-list(mac extended)
      • 18.2.2.6 access-list(mac-ip extended)
      • 18.2.2.7 access-list(mac standard)
      • 18.2.2.8 clear access-group statistic
      • 18.2.2.9 firewall
      • 18.2.2.10 firewall default
      • 18.2.2.11 access-list ip extended
      • 18.2.2.12 access-list ip standard
      • 18.2.2.13 ipv6 access-list
      • 18.2.2.14 ipv6 access standard
      • 18.2.2.15 ipv6 access extended
      • 18.2.2.16 {ip|ipv6|mac|mac-ip} access-group
      • 18.2.2.17 mac access extended
      • 18.2.2.18 mac-ip access extended
      • 18.2.2.19 permit | deny( ip extended)
      • 18.2.2.20 permit | deny(ip standard)
      • 18.2.2.21 permit | deny(mac extended)
      • 18.2.2.22 permit | deny(mac-ip extended)
      • 18.2.2.23 permit | deny(ipv6 extended)
      • 18.2.2.24 permit | deny(ipv6 standard)
      • 18.2.2.25 time-range
  • 18.3 ACL Example
  • 18.4 ACL Troubleshooting
    • 18.4.1 Command for Monitor And Debug
      • 18.4.1.1 show access-lists
      • 18.4.1.2 show access-group
      • 18.4.1.3 show firewall
      • 18.4.1.4 show time-range
      • 18.4.1.5 show ipv6 access-lists
  • 18.5 Web Management
    • 18.5.1 Numeric standard ACL configuration
    • 18.5.2 Delete numeric IP ACL
    • 18.5.3 Configure the numeric extended ACL
    • 18.5.4 Configure and delete the standard ACL name
    • 18.5.5 Configure extended ACL name configuration
    • 18.5.6 Firewall configuration
    • 18.5.7 ACL port binding
• Chapter 19 802.1x Configuration
  • 19.1 Introduction to 802.1x
  • 19.2 802.1x Configuration Task List
  • 19.3 Commands for 802.1x
    • 19.3.1 aaa enable
    • 19.3.2 aaa-accounting enable
    • 19.3.3 dot1x accept-mac
    • 19.3.4 dot1x eapor enable
    • 19.3.5 dot1x enable
    • 19.3.6 dot1x macfilter enable
    • 19.3.7 dot1x max-req
    • 19.3.8 dot1x max-user
    • 19.3.9 dot1x port-control
    • 19.3.10 dot1x port-method
    • 19.3.11 dot1x re-authenticate
    • 19.3.12 dot1x re-authentication
    • 19.3.13 dot1x timeout quiet-period
    • 19.3.14 dot1x timeout re-authperiod
    • 19.3.15 dot1x timeout tx-period
    • 19.3.16 radius-server accounting host
    • 19.3.17 radius-server authentication host
    • 19.3.18 radius-server dead-time
    • 19.3.19 radius-server key
    • 19.3.20 radius-server retransmit
    • 19.3.21 radius-server timeout
  • 19.4 802.1x Application Example
  • 19.5 802.1x Troubleshooting
    • 19.5.1 Command for Monitor and debug
      • 19.5.1.1 debug aaa
      • 19.5.1.2 debug dot1x
      • 19.5.1.3 show aaa authenticated-user
      • 19.5.1.4 show aaa authenticating-user
      • 19.5.1.5 show aaa config
      • 19.5.1.6 show dot1x
      • 19.5.1.7 show radius count
  • 19.6 Web Management
    • 19.6.1 RADIUS client configuration
      • 19.6.1.1 RADIUS global configuration
      • 19.6.1.2 RADIUS authentication configuration
      • 19.6.1.3 RADIUS accounting configuration
    • 19.6.2 802.1X configuration
      • 19.6.2.1 802.1X configuration
      • 19.6.2.2 802.1X port authentication configuration
      • 19.6.2.3 802.1X port mac configuration
      • 19.6.2.4 802.1X port status list
• Chapter 20 VRRP Configuration
  • 20.1 Introduction to VRRP
  • 20.2 Configuration Task List
  • 20.3 Commands for VRRP
    • 20.3.1 advertisement-interval
    • 20.3.2 circuit-failover
    • 20.3.3 debug vrrp
    • 20.3.4 disable
    • 20.3.5 enable
    • 20.3.6 interface
    • 20.3.7 preempt-mode
    • 20.3.8 priority
    • 20.3.9 router vrrp
    • 20.3.10 show vrrp
    • 20.3.11 virtual-ip
  • 20.4 Typical VRRP Scenario
  • 20.5 VRRP Troubleshooting
  • 20.6 Web Management
    • 20.6.1 Create VRRP Number
    • 20.6.2 Configure VRRP Dummy IP
    • 20.6.3 Configure VRRP Port
    • 20.6.4 Activate Virtual Router
    • 20.6.5 Configure Preemptive Mode For VRRP
    • 20.6.6 Configure VRRP priority
    • 20.6.7 Configure VRRP Timer interval
    • 20.6.8 Configure VRRP Interface Monitor
    • 20.6.9 Configure Authentication Mode For VRRP
• Chapter 21 MRPP Configuration
  • 21.1 MRPP introduction
    • 21.1.1 Conception Introduction
    • 21.1.2 MRPP Protocol Packet Types
    • 21.1.3 MRPP Protocol Operation System
  • 21.2 MRPP Configuration Task List
  • 21.3 Commands For MRPP
    • 21.3.1 clear mrpp statistics
    • 21.3.2 control-vlan
    • 21.3.3 debug mrpp
    • 21.3.4 enable
    • 21.3.5 fail-timer
    • 21.3.6 hello-timer
    • 21.3.7 mrpp enable
    • 21.3.8 mrpp ring
    • 21.3.9 node-mode
    • 21.3.10 primary-port
    • 21.3.11 secondary-port
    • 21.3.12 show mrpp
    • 21.3.13 show mrpp statistics
  • 21.4 MRPP typical scenario
    • 21.4.1 MRPP typical scenario 1
    • 21.4.2 MRPP typical scenario 2
    • 21.4.3 MRPP typical scenario 3
  • 21.5 MRPP troubleshooting
• Chapter 22 Cluster Configuration
  • 22.1.1 Introduction to cluster network management
    • 22.1.2 Cluster Network Management Configuration Sequence
    • 22.1.3 Commands for cluster
      • 22.1.3.1 cluster run
      • 22.1.3.2 cluster register timer
      • 22.1.3.3 cluster ip-pool
      • 22.1.3.4 cluster commander
      • 22.1.3.5 cluster member
      • 22.1.3.6 cluster auto-add enable
      • 22.1.3.7 rcommand member
      • 22.1.3.8 rcommand commander
      • 22.1.3.9 cluster reset member
      • 22.1.3.10 cluster update member
      • 22.1.3.11 cluster holdtime
      • 22.1.3.12 cluster heartbeat
      • 22.1.3.13 clear cluster candidate-table
    • 22.1.4 Examples of Cluster Administration
    • 22.1.5 Cluster Administration Troubleshooting
      • 22.1.5.1 Cluster Administration Debugging and Monitoring Command
        • 22.1.5.1.1 show cluster
        • 22.1.5.1.2 show cluster members
        • 22.1.5.1.3 show cluster candidates
        • 22.1.5.1.4 debug cluster packets
        • 22.1.5.1.5 debug cluster application
        • 22.1.5.1.6 debug cluster statemach
      • 22.1.5.2 Cluster administration troubleshooting