Document Outline

• Cyclone II DSP Development Board
  • Contents
  • About This Manual
    • Revision History
    • How to Contact Altera
    • Typographic Conventions
  • Chapter 1. Introduction
    • Introduction
    • Features Overview
      • Components
  • Chapter 2. Cyclone II DSP Development Board Components
    • Introduction
    • Components & Interfaces
    • Featured Device
    • User Interfaces
      • User-Defined LEDs (D2 Through D9)
      • User Defined DIP Switch (S1)
      • User-Defined Pushbuttons (SW2 Through SW5)
      • Seven-Segment Display (U32,U33)
      • Audio CODEC Converter (U11)
      • Audio Jacks (J10, J14, J16)
      • VGA Output Connector (J21)
      • VGA Triple Video D/A Output Converter (U21)
      • D/A Converter SMA Connector (J31 & J43)
      • D/A Converter Clock Buffer (U27 & 30)
      • D/A Converter (U25 & U30)
        • D/A Converter Clocks
      • A/D Converter Data Format Select Jumper (J30 & J38)
      • A/D Converter SMA Connector (J32 & J44)
      • A/D Converter Clock Buffer (U29 & U28)
      • A/D Converter (U26 & U31)
        • A/D Converter Clocks
    • Memory Components
      • DDR2 SDRAM DIMM (J8)
        • DDR2 SDRAM DIMM Clocks
      • DIMM_SYNC_CLK SMA Connector (J11)
      • SSRAM Sleep & Run Modes (J24)
      • EPCS Select (J29)
      • EPCS64 Flash Memory Devices (U17, U36)
      • Synchronous SRAM Device (U22)
      • Memory Mapping to the TMS320C6416 Digital Signal Processor
    • Expansion Connectors
      • Expansion Prototype Connector (J15, J22 & J23)
      • Expansion TI-EVM Connectors (U34, U40)
    • General Connectors
      • JTAG Connector (J9)
      • Active Serial Interface (ASI) Connector (J13)
      • Mictor Connector (J12)
    • Status LEDs & Reset/Power Switches
      • Power (D1) & Status (D10) LEDs
      • Power Switch (SW1)
      • User Defined Reset (SW6) Push-Button
      • System Reset (SW7) Push-Button
    • Clock Circuitry
      • Setting the Clocks
      • CLK SMA Connector (J17)
      • On-Board/Custom Clock Oscillators Select Jumper (J18)
      • Clock Select Jumper (J19)
      • Socket for a Custom Clock Oscillator (J20)
      • D/A Converter CLK SMA Connector (J26)
      • A/D Converter CLK SMA Connector (J27)
      • D/A Converter CLK Select Jumper (J35 & J34)
      • A/D Converter CLK Select Jumper (J37 & J36)
      • D/A Converter Power Select Jumper (J33)
      • Clock Buffer (U16)
      • On-Board Clock Oscillator (U20)
    • Power Supply
      • DC Power Input Jack (J1)
        • Cyclone II DSP Development Board Power-Up
      • Voltage Limiter Switches (U13-U15, U18 & U19)
      • On-Board Power Regulators (U2, U7, U8, U9, U10, U23 & U24)
      • Bench Power Supplies Using Banana Jacks
      • Power Plane Connectors (J2-J6, J39 Through J42)
  • Appendix A. DDR2 SDRAM DIMM Connector Pin Out Table
    • Introduction
  • Appendix B. SSRAM Pin-Out Table
    • Introduction
  • Appendix C. Cyclone II EP2C70 Device Pin-Out Table
    • Introduction
  • Appendix D. Restoring the Factory Design
    • Introduction
      • Factory-Programmed Factory Design
      • User Designs
      • Reprogramming the Factory Design to the EPSC64 Device (U17)