Document Outline

• electrONIC Electric DRYERS
  • Use & Care Guide
    • For questions about features, operation/performance, parts, accessories or service, call: 1-800-688-9900
    • or visit our website at... www.amana.com
      • Table of Contents 2
• Table of Contents
• dryer Safety
• iNSTALLATION INSTRUCTIONS
  • Tools and Parts
    • Parts supplied
    • 4 Leveling legs
      • Parts needed
• If using a power supply cord:
  • Optional Pedestal
    • Optional pedestal (15.5" [394 mm] model shown)
• Pedestal Height
• Color
• Part Number
• 10" (254 mm)
  • Location Requirements
    • You will need
    • Installation clearances
    • Dryer Dimensions
    • Installation spacing for recessed area or closet installation
    • A. Side view - closet or confined area
    • B. Closet door with vents
    • A. Recessed area
    • B. Side view - closet or confined area
• Installation spacing for cabinet installation
• Recommended installation spacing for recessed or closet installation, with stacked washer and dryer
  • Mobile home - additional installation requirements
  • Mobile home installations require:
    • Electrical Requirements
      • It is your responsibility
      • Electrical Connection
  • If using a power supply cord:
  • If your outlet looks like this:
    • 4-wire receptacle (14-30R)
  • If your outlet looks like this:
    • 3-wire receptacle (10-30R)
  • If connecting by direct wire:
    • Electrical Connection
• Power Supply Cord
• Direct Wire
  • 1. Disconnect power.
  • 2. Remove the hold-down screw and terminal block cover.
    • A. Neutral ground wire
    • B. External ground conductor screw
    • C. Center, silver-colored terminal block screw
    • D. Terminal block cover and hold-down screw
  • 3. Install strain relief.
    • Remove the screws from a ¾" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold ...
      • A. Strain relief tab pointing up
      • B. Hole below terminal block opening
      • C. Clamp section
      • D. Strain relief tab pointing down
    • Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further t...
    • Unscrew the removable conduit connector and any screws from a ¾" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the term...
      • A. Removable conduit connector
      • B. Hole below terminal block opening
      • C. Strain relief threads
    • Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.
  • 4. Now complete installation following instructions for your type of electrical connection:
    • Electrical Connection Options
    • If your home has:
    • And you will be connecting to:
    • Go to Section
• 4-wire connection: Power supply cord
  • A. 4-wire receptacle (NEMA type 14-30R)
  • B. 4-prong plug
  • C. Ground prong
  • D. Neutral prong
  • E. Spade terminals with upturned ends
  • F. ¾" (19 mm) UL listed strain relief
  • G. Ring terminals
    • 1. Remove center silver-colored terminal block screw.
  • 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.
    • A. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw.
    • B. Center silver-colored terminal block screw
    • C. Neutral ground wire
    • D. Neutral wire (white or center wire)
    • E. ¾" (19 mm) UL listed strain relief
  • 3. Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.
    • A. External ground conductor screw
    • B. Ground wire (green or bare) of power supply cord
    • C. ¾" (19 mm) UL listed strain relief
    • D. Center silver-colored terminal block screw
    • E. Neutral ground wire
    • F. Neutral wire (white or center wire)
  • 4. Connect the other wires to outer terminal block screws. Tighten screws.
  • 5. Tighten strain relief screws.
  • 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.
  • 7. You have completed your electrical connection. Now go to “Venting Requirements.”
• 4-wire connection: Direct wire
  • 1. Remove center silver-colored terminal block screw.
  • 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block....
    • A. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw.
    • B. Center silver-colored terminal block screw
    • C. Neutral ground wire
    • D. Neutral wire (white or center wire)
    • E. ¾" (19 mm) UL listed strain relief
  • 3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.
    • A. External ground conductor screw
    • B. Ground wire (green or bare) of power supply cable
    • C. ¾" (19 mm) UL listed strain relief
    • D. Center silver-colored terminal block screw
    • E. Neutral ground wire
    • F. Neutral wire (white or center wire)
  • 4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.
  • 5. Tighten strain relief screw.
  • 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.
  • 7. You have completed your electrical connection. Now go to “Venting Requirements.”
• 3-wire connection: Power supply cord
  • Use where local codes permit connecting cabinet-ground conductor to neutral wire.
    • A. 3-wire receptacle (NEMA type 10-30R)
    • B. 3-wire plug
    • C. Neutral prong
    • D. Spade terminals with upturned ends
    • E. ¾" (19 mm) UL listed strain relief
    • F. Ring terminals
    • G. Neutral (white or center wire)
      • 1. Loosen or remove center silver-colored terminal block screw.
  • 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.
    • A. External ground conductor screw
    • B. Neutral ground wire
    • C. Center silver-colored terminal block screw
    • D. Neutral wire (white or center wire)
    • E. ¾" (19 mm) UL listed strain relief
  • 3. Connect the other wires to outer terminal block screws. Tighten screws.
  • 4. Tighten strain relief screws.
  • 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.
  • 6. You have completed your electrical connection. Now go to “Venting Requirements.”
• 3-wire connection: Direct wire
  • Use where local codes permit connecting cabinet-ground conductor to neutral wire.
    • 1. Loosen or remove center silver-colored terminal block screw.
  • 2. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.
    • A. External ground conductor screw
    • B. Neutral ground wire
    • C. Center silver-colored terminal block screw
    • D. Neutral wire (white or center wire)
    • E. ¾" (19 mm) UL listed strain relief
  • 3. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.
  • 4. Tighten strain relief screw.
  • 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.
  • 6. You have completed your electrical connection. Now go to “Venting Requirements.”
• Optional 3-wire connection
  • Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.
    • 1. Remove center silver-colored terminal block screw.
  • 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.
    • A. External ground conductor screw
    • B. Center silver-colored terminal block screw
    • C. Neutral ground wire
    • D. Neutral wire (white or center wire)
    • E. ¾" (19 mm) UL listed strain relief
    • F. Grounding path determined by a qualified electrician
  • 3. Connect the other wires to outer terminal block screws. Tighten screws.
  • 4. Tighten strain relief screws.
  • 5. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.
  • 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.
    • Venting Requirements
• If using an existing vent system
• If this is a new vent system
  • Vent material
  • 4" (102 mm) heavy metal exhaust vent
  • Rigid metal vent
  • Flexible metal vent
  • Elbows
    • Good
    • Better
  • Clamps
    • Clamp
  • Exhaust
    • A. Louvered hood style
    • B. Box hood style
    • Plan Vent System
• Choose your exhaust installation type
  • Recommended exhaust installations
  • A. Dryer
  • B. Elbow
  • C. Wall
  • D. Exhaust hood
  • E. Clamps
  • F. Rigid metal or flexible metal vent
  • G. Vent length necessary to connect elbows
  • H. Exhaust outlet
    • Optional exhaust installations
  • A. Standard rear offset exhaust installation
  • B. Left or right side exhaust installation
  • C. Bottom exhaust installation (not an option with pedestal installations)
    • Alternate installations for close clearances
  • A. Over-the-top installation (also available with one offset elbow)
  • B. Periscope installation
    • Special provisions for mobile home installations
• Determine vent path
• Determine vent length and elbows needed for best drying performance
  • Shorten the life of the dryer.
  • Reduce performance, resulting in longer drying times and increased energy usage.
    • Vent system chart
  • Number of 90º turns or elbows
  • Type of vent
  • Box or Louvered hoods
  • Angled hoods
  • 0
  • Rigid metal
  • 1
  • Rigid metal
  • 2
  • Rigid metal
  • 3
  • Rigid metal
  • 4
  • Rigid metal
    • Install Vent System
      • 1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.
  • 2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp.
  • 3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into the ...
    • Install Leveling Legs
      • 1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.
  • 2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration.
  • 3. Examine the leveling legs. Find the diamond marking.
  • 4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.
  • 5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.
    • Connect Vent
      • 1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to e...
  • 2. Move dryer into its final location. Do not crush or kink vent.
  • 3. (On gas models) Check that there are no kinks in the flexible gas line.
  • 4. Once the exhaust vent connection is made, remove the corner posts and cardboard.
    • Level Dryer
    • Reverse Door Swing
      • Remove the door
        • 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.
  • 2. Open the dryer door. Remove the 5 screws that hold the door hinge on the front panel of the dryer.
    • A. Dryer front panel
    • B. Dryer door
    • C. Screws
  • 3. Remove the door.
  • 4. Lay the dryer door on a flat, protected surface with the inside door assembly facing up.
  • 5. Lift the inner door assembly off of the outer door assembly. Set the outer door assembly aside.
    • Reverse the hinge
      • 1. Place the inner door, screw head side up, on the work space.
  • 2. Remove the 4 hinge screws that hold the hinge to the door and remove hinge.
    • A. Hinge side screw
    • B. Locator pins on hinge
    • C. Top side screw
  • 3. Move the large hole screw to the opposite side. Remove the 2 plug screws and plastic plugs, and insert them in the original screw holes on the opposite side.
    • A. Hinge screws
    • B. Large hole screw
    • C. Plug screws and plastic plugs
  • 4. Move hinge to the other side and reattach with the 4 screws removed in Step 2. Make sure locator pins line up in holes and drive the top 2 screws in place first to help drive locator pins into proper location.
  • 5. Set the inner door assembly aside.
    • Reverse the door handle
      • 1. Place the outer door assembly face down on work space.
  • 2. Remove the 6 screws that hold the intermediate door to the outer door assembly. Remove the intermediate door, and set hinge shield aside. Remove the hinge hole cover.
    • A. Intermediate door
    • B. Hinge shield
    • C. Hinge hole cover
  • 3. Rotate the window assembly 180º and reattach the intermediate door, hinge shield, and hinge hole cover with the 6 screws removed in Step 2.
    • Reinstalling the door
      • 1. Place the inner door assembly into the outer door assembly. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge.
  • 2. Reassemble the inner and outer door assemblies with the 5 screws.
  • 3. Remove existing label from the opposite side of the door and discard. Find label provided with the Use and Care Guide and apply over original hinge holes.
  • 4. Align the door by placing the locating tabs on the hinge with the locating holes on the dryer front panel. Insert and tighten the center hinge screw. The door will hang in place while you insert and tighten the remaining 4 screws.
    • A. Dryer door
    • B. Dryer front panel
    • C. Insert this hinge screw first.
  • 5. Close the door and check that it latches securely.
  • 6. Check for fingerprints on the glass. Clean the glass if necessary.
    • Complete Installation
      • 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
  • 2. Check that you have all of your tools.
  • 3. Dispose of/recycle all packaging materials.
  • 4. Check the dryer’s final location. Be sure the vent is not crushed or kinked.
  • 5. Check that the dryer is level. See “Level Dryer.”
  • 6. For power supply cord installation, plug into an outlet. For direct wire installation, reconnect power.
  • 7. Remove the blue protective film on the console and any tape remaining on the dryer.
  • 8. Read “Dryer Use.”
  • 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.
  • 10. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Dry Temperature setting.
    • Controls are set in a running or “On” position.
    • The Start button has been pushed firmly.
    • Dryer is plugged into an outlet and/or electrical supply is connected.
    • Household fuse is intact and tight, or circuit breaker has not tripped.
    • Dryer door is closed.
    • Dryer Use
      • Starting Your Dryer
        • 1. Clean lint screen before each load. See “Cleaning the Lint Screen.”
  • 2. Place laundry in dryer and shut door.
  • 3. Press the POWER button. Then rotate the dial or press a Timed Cycles button to select the desired Automatic or Timed Cycle. The indicator light for the selected Automatic or Timed cycle will glow green. The preset modifiers for the selected cycle ...
    • Select an Automatic Cycle.
    • Select DRYNESS LEVEL to adjust how dry you want the load. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected dryness level.
    • Select the desired Options.
    • Press STOP once.
    • Adjust Dryness Level.
    • Press a Timed Cycles button or, to select Air Fluff, rotate the control knob to the desired cycle.
    • Press MORE TIME or LESS TIME until the desired drying time is displayed. Tap MORE TIME or LESS TIME, and the time will change by 1-minute intervals. Press and hold MORE TIME or LESS TIME, and the time will change by 5-minute intervals.
    • Press TEMPERATURE until the desired temperature glows.
  • 4. (OPTIONAL STEP) If desired, select OPTIONS. For more details, see “Options.”
  • 5. (OPTIONAL STEP) If desired, set the End of Cycle Signal. Select LOUD or SOFT by pressing the Cycle Signal button to alert you when a cycle ends.
  • 6. Press and hold START for approximately 3 seconds until dryer starts. Be sure the door is closed.
    • If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.
    • If you wish to end your drying cycle after pressing Start, press Stop twice.
    • Stopping Your Dryer
      • To stop your dryer at any time
    • Pausing or Restarting
      • To pause the dryer at any time
      • To restart the dryer
    • Control Locked
    • To enable the Control Locked feature:
      • Drying and Cycle Tips
        • Drying tips
        • Cycle tips
        • Drying temperature and Dryness Level are preset when you choose an Automatic Cycle. You can select a different dryness level, depending on your load, by pressing Dryness Level and choosing More Dry, Normal or Less Dry.
        • If you wish to adjust the cycle length of a Timed Cycle, press More Time or Less Time. Adjust the temperature of a Timed Cycle by pressing TEMPERATURE until the desired temperature is selected.
      • Status Lights
        • Timed Cycle
        • Wet
        • Damp
        • Cool Down
        • Clothes Dry
        • Wrinkle Prevent
        • Sensing/Revising Est. Time
        • Indicator lights
      • Cycles
• Automatic Cycles
  • Heavy Duty
  • Denim
  • Normal
  • Casual
  • Delicate
  • Automatic Dry Preset Cycle Settings
  • Automatic Cycles Load Type
  • Temperature
  • Time* (Minutes)
• Timed Cycles
  • Timed Dry
  • Quick Dry
  • Touch Up
  • Air Fluff
  • Type of Load
  • Time* (Minutes)
  • When using Air Fluff
    • Timed Preset Cycle Settings
  • Timed Cycles Load Type
  • Default Temperature
  • Default Time (Minutes)
    • Options
      • Wrinkle Prevent
      • Damp Dry Signal
      • Button Sounds
      • Drum Light
    • Modifiers
      • Time
      • Temperature
      • Dryness Level
    • Changing Cycles, Options, and Modifiers
      • Changing Cycles after pressing Start
        • 1. Press STOP twice. This ends the current cycle.
  • 2. Select the desired cycle and options.
  • 3. Press and hold START. The dryer starts at the beginning of the new cycle.
    • Changing Modifiers and Options after pressing Start
      • 1. Press STOP once.
  • 2. Select the new Modifier and/or Option.
  • 3. Press and hold START to continue the cycle.
    • Changing the Preset Dryness Level Settings
      • 1. The Dryness Level settings cannot be changed while the dryer is running.
  • 2. Press and hold the DRYNESS LEVEL button for 5 seconds. The dryer will beep, and “CF” will be displayed for 1 second followed by the current drying setting.
  • 3. To select a new drying setting, press the DRYNESS LEVEL button again until the desired drying setting is shown. NOTE: While you are cycling through the settings, the current setting will not flash, but the other settings will flash.
  • 4. Press START to save the drying setting.
    • End of Cycle Signal
      • End of Cycle Signal
    • Drying Rack Options
    • To use the heated dryer rack:
      • 1. Open dryer door.
      • A. Front edge
  • 2. Place dryer rack over the bottom of the dryer door opening. Rest the back wire on the dryer back ledge. Push down on the frame front to secure over lint screen.
    • A. Dryer rack front edge
    • B. Dryer back panel
  • 3. Place wet items on top of the rack. Allow space around items for air to circulate. The rack does not move, but the drum will rotate. Make sure items do not hang over the edges or between rack grille.
  • 4. Close the door.
  • 5. Rotate the dial to the Air Fluff cycle or press Timed Dry. Select a drying time by pressing MORE TIME or LESS TIME. Press TEMPERATURE until the desired temperature glows. Items containing foam, rubber, or plastic must be dried on a clothesline or ...
  • 6. When Air Fluff is selected, the Estimated Time Remaining display shows the default time. You can change the actual time in the cycle by pressing More Time or Less Time.
  • 7. Start the dryer.
    • Dryer Rack
    • Cycle
    • Temp.
    • Time*
    • Wool sweaters
    • Stuffed toys or pillows
    • Stuffed toys or pillows
    • Sneakers or canvas shoes
      • dryer care
        • Cleaning the Dryer Location
        • Cleaning the Lint Screen
          • Every load cleaning
    • To clean
      • 1. Pull the lint screen straight up. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.
  • 2. Push the lint screen firmly back into place.
    • IMPORTANT:
      • As needed cleaning
    • To wash
      • 1. Roll lint off the screen with your fingers.
  • 2. Wet both sides of lint screen with hot water.
  • 3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.
  • 4. Rinse screen with hot water.
  • 5. Thoroughly dry lint screen with a clean towel. Replace screen in dryer.
    • Cleaning the Dryer Interior
      • To clean dryer drum
        • 1. Make a paste with powdered laundry detergent and very warm water.
  • 2. Apply paste to a soft cloth.
  • 3. Wipe drum thoroughly with a damp cloth.
  • 4. Tumble a load of clean cloths or towels to dry drum.
    • Removing Accumulated Lint
      • From Inside the Dryer Cabinet
      • From the Exhaust Vent
    • Vacation and Moving Care
• Vacation care
  • 1. Unplug dryer or disconnect power.
  • 2. Clean lint screen. See “Cleaning the Lint Screen.”
• Moving care
  • For power supply cord-connected dryers:
    • 1. Unplug the power supply cord.
  • 2. Make sure leveling legs are secure in dryer base.
  • 3. Use masking tape to secure dryer door.
    • For direct-wired dryers:
      • 1. Disconnect power.
  • 2. Disconnect wiring.
  • 3. Make sure leveling legs are secure in dryer base.
  • 4. Use masking tape to secure dryer door.
    • Changing the Drum Light
      • To change the drum light
        • 1. Unplug dryer or disconnect power.
  • 2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover.
  • 3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the screw.
  • 4. Plug in dryer or reconnect power.
    • troubleshooting
      • First try the solutions suggested here and possibly avoid the cost of a service call...
      • Dryer Operation
• Dryer will not run
• No heat
• Unusual sounds
• Dryer displaying code message
  • Dryer Results
• Clothes are not drying satisfactorily, drying times are too long, or load is too hot
• Cycle time too short
• Lint on load
• Stains on load or drum
• Loads are wrinkled
• Odors
  • Assistance or Service
    • If you need replacement parts
    • For Assistance and Service
  • Our consultants provide assistance with:
  • For further assistance
    • Maytag Services, LLC Attn: CAIR® Center P.O. Box 2370 Cleveland, TN 37320-2370
    • Amana® LAUNDRY WARRANTY
      • LIMITED WARRANTY
        • For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Amana brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Amana”) will...
      • ITEMS EXCLUDED FROM WARRANTY
        • 1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
          • 2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.
          • 3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.
          • 4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Amana.
          • 5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Amana within 30 days from the date of purchase.
          • 6. Pick up and delivery. This major appliance is intended to be repaired in your home.
          • 7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
          • 8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Amana servicer is not available.
          • 9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Amana’s published installation instructions.
          • 10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.
      • DISCLAIMER OF IMPLIED WARRANTIES
        • IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the du...
      • LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
        • YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. AMANA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental...
        • If outside the 50 United States and Canada, contact your authorized Amana dealer to determine if another warranty applies.
        • If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Se...