Document Outline

• Metreau™ Entry Communicators - Operation/Reference Guide
  • Metreau Entry Communicators
    • Overview
      • Front Components
      • Rear Components
    • Product Specifications - MET-ECOM
    • Product Specifications - MET-ECOM-D
  • Positioning the Camera
    • Overview
      • Camera Viewing Angle Adjustment
  • Wiring and Connections
    • Overview
    • Rear Panel Connectors
    • Ethernet 10/100 Base-T RJ-45 Wiring Configuration
      • PoE (Power Over Ethernet)
    • Input/Output (I/O) Port: Connections and Wiring
      • Connecting The Device via I/O
    • Relay Port: Connections and Wiring
    • Ferrite Installation (Required)
      • System Diagram
      • System Diagram - Intercom
  • Mounting and Installation
    • MET-ECOM / MET-ECOM-D Installation Overview
    • Dimensions
    • Mounting Specifications
      • Front View
      • Side Views
      • Top View
      • Typical Installation (Without Expansion Clips)
      • Installing the Wall Box Without the Use of Tabs
      • Wall Surface Installation (Using Expansion Clips)
      • Installing Into a Flat Surface Using Mounting Screws
      • Removing the Device From the Wall
    • Using the Optional Surface Mount Box
      • Included in the Kit
      • Surface Mount Box Specifications
      • Ferrite Installation (Required)
      • Installing the Metreau Entry Communicator
  • Using the Configuration Manager
    • Overview
      • Command Buttons
      • Accessing the Configuration Manager
    • Summary of <Device> Settings Page
      • Checking the Firmware Version
      • Determining the IP settings of the Metreau Entry Communicator
      • Rebooting the Device
    • Configuration Page
      • Configuration Page - Network IP Settings Tab
      • Setting the IP Address
      • Setting the DNS Address
      • Configuration Page - NetLinx Settings Tab
      • Setting the ICSP Connection to the NetLinx Master
      • Configuration Page - User Settings Tab
      • Setting a New Username and Password
    • Device Utilities Page
      • Image File Requirements
    • Creating Display Images
    • Creating Dynamic Images
      • TPDesign4 - Resource Manager
      • Creating a New Dynamic Image
      • Uploading a Display Image To The Device
      • Deleting a Display Image From the Device
    • Audio/Video Page
      • Audio/Video Page - Audio Settings Tab
      • Setting Device Audio
      • Audio/Video Page - Video Settings Tab
      • Setting Device Video
      • Audio/Video Page - Display Settings Tab
      • Setting the Display Settings On The Device
  • Programming
    • Overview
    • SEND_COMMANDs
      • Touch Panel Intercom Commands
      • RTP, RTCP Video and Audio Streaming Commands
      • Face Plate LED Commands
      • Camera Commands
      • LCD Commands
      • I/O Commands
      • System Commands
    • Upgrading Firmware
      • Before beginning the Upgrade process
    • Upgrading Firmware via an IP Address
      • Preparing the Master for communication via an IP
      • Verifying and Upgrading the device firmware via an IP
  • Using the NetLinx Module
    • Overview
    • Incorporating an Intercom Panel Into Your NetLinx System
    • Panel Intercom Configuration
      • Intercom Setup
      • Setting the Intercom Session Timeout
      • Setting Intercom Auto Answer
      • Door Setup
      • Disabling All Doorbells
      • Door Chime Setup
      • Assigning a Chime To a Doorbell
      • Advanced Setup
      • Allowing a Panel To Be Monitored
      • Allowing a Panel To Monitor
      • Naming a panel
      • Answering an incoming Intercom call
      • Answering an Incoming Doorbell Call
    • Someone At The Door Page
      • Ending a Doorbell Call
    • Creating Intercom Pages
      • Advanced Setup page
      • Door Chime Setup page
      • Door Setup page
      • Intercom Demo page
      • Setup page
      • Someone At The Door page
    • Creating Popup Pages
      • Door Answer Call popup page
      • Doorbell Adjustments popup page
      • Intercom Answer Call popup page
      • More Time popup page