Document Outline

• NXD-CV7 and NXT-CV7 7" Modero Widescreen Video Touch Panels (Firmware version G4)
  • Introduction
    • CV7 Specifications
    • CV7 Panels - Connector Layout
  • CV7 Touch Panel Accessories
    • NXA-AVB/ETHERNET Breakout Box (FG2254-10)
      • Product Specifications
      • Installing the NXA-AVB/ETHERNET
      • Wiring the NXA-AVB/ETHERNET connectors and cables
      • Wiring the NXA-AVB/ETHERNET for Unbalanced Audio
      • Wiring the NXA-AVB/ETHERNET for Balanced Audio
    • Modero Table Top Cable (CA2250-50)
      • Product Specifications
      • Wiring information for the Modero Table Top cable
    • NXA-WC80211B/CF 802.11b Wireless Card (FG2255-03)
      • Installation of the Wireless Card (Table Top Panel)
      • Step 1: Removing the NXT Outer Housing
      • Step 2: Upgrading internal components (Compact Flash and Wireless cards)
      • Step 3: Closing and Securing the NXT Enclosure
      • Installation of the Wireless Card (WallMount Panel)
      • Step 1: Removing the existing NXD Outer Housing
      • Step 2: Installing the Upgrade Components (NXD)
      • Step 3: Replacing and Securing the NXD Enclosure
    • NXA-CFSP Compact Flash (2116-3x)
      • Installation Procedures for the Compact Flash Card (Table Top Panel)
      • Installation Procedures for the Compact Flash Card (WallMount Panel)
    • NXT-BP Power Pack (FG2255-10)
    • NXA-BASE/1 Battery Base Kit (FG2255-05K)
      • Checking the NXT-BP charge
      • Installing an NXT-BP into the NXA-BASE/1
      • Installing the NXA-BASE/1 below an NXT-CV7 Panel
      • Charging the NXT-BP using the NXA-BASE/1
    • NXT-CHG Battery Charger Kit (FG2255-50K)
      • Powering the NXT-CHG
      • Reading the NXT-CHG LED Indicator
      • Charging the NXT-BP batteries using the NXT-CHG
      • Recalibrating the batteries
  • Installation
    • Unpacking the Panel
    • Installing the Internal Components
    • Installing the No-Button Trim Ring
    • Installing the Button Trim Ring
    • Pre-Wall Installation of the Conduit Box
    • Installation of an NXD Touch Panel
      • Installing the NXD panel within a Conduit Box
      • Installing the NXD into drywall using Expansion Clips
      • Installing the NXD into a Flat Surface using #4 screws
      • Installing an NXD-CV7 into an (optional) Rack Mount Kit (NXA-RK7)
    • Wiring Guidelines for the CV7 Panels
      • Preparing captive wires
      • Using the PSN NetLinx connector for power
    • Audio/Video RJ-45 Connections and Wiring
    • Ethernet 10/100 Base-T RJ-45 Connections and Wiring
    • Connecting and Using USB Input Devices
  • Panel Calibration
    • Calibrating the Modero Panel
      • Testing your Calibration
  • Configuring Communication
    • Modero Setup and System Connection
    • Configuring and Using USB with a Virtual Master
      • Step 1: Setup the Panel and PC for USB Communication
      • Step 2: Confirm the Installation of the USB Driver on the PC
      • Step 3: Confirm and View the current AMX USB device connections
      • Step 4: Use the USB to Configure a Virtual Master (using NetLinx Studio)
      • Step 5: Confirm and View the current AMX USB device connections
    • Secondary Connection Page - Wireless Access Overview
      • IP Routing
      • Hot Swapping
    • Configuring a Wireless Network Access
    • Step 1: Configure the Panel’s Wireless IP Settings
      • Wireless communication using a DHCP Address
      • Wireless communication using a Static IP Address
    • Step 2: Configure the Card’s Wireless Security Settings
      • Configuring the Modero’s wireless card for unsecured access to a WAP200G
      • Configuring the Modero’s wireless card for secured access to a WAP200G
      • Configuring multiple wireless Moderos to communicate to a target WAP200G
    • Configuring a Wired Ethernet Connection
    • Step1: Configure the Panel’s Wired IP Settings
      • IP Settings section - Configuring a DHCP Address over Ethernet
      • IP Settings section - Configuring a Static IP Address over Ethernet
    • Step 2: Choose a Master Connection Mode Setting
    • Step 3: Configure an Ethernet Connection Type
      • Master Connection section - Virtual Master communication over Ethernet
      • Master Connection section - NetLinx Master Ethernet IP Address - URL Mode
      • Master Connection section - NetLinx Master Ethernet IP Address - Listen Mode
      • Master Connection section - NetLinx Master Ethernet IP Address - Auto Mode
    • Using G4 Web Control to Interact with a G4 Panel
    • Accessing the NetLinx Master via an IP Address
    • Using your NetLinx Master to Control the G4 panel
  • Upgrading Modero Firmware
    • Upgrading the Modero Firmware via the USB port
      • Step 1: Configure the panel for a USB Connection Type
      • Step 2: Prepare NetLinx Studio for communication via the USB port
      • Step 3: Confirm and Upgrade the firmware via the USB port
    • Upgrading the Modero Firmware via Ethernet (IP Address)
      • Step 1: Prepare the Master for communication via an IP
      • Step 2: Prepare the panel for communication via an IP
      • Step 3: Verify and Upgrade the panel firmware via an IP
  • Firmware Pages and Descriptions
    • Setup Navigation Buttons
    • Setup Page
      • Project Information Page
      • Panel Information Page
      • Time & Date Setup Page
      • Volume Page
      • Supported sampling rates for WAV
      • Protected Setup Page
      • Video Adjustment Page
      • Battery Base Page
    • Protected Setup Navigation Buttons
    • Protected Setup Page
      • G4 Web Control Page
      • Sensor Setup
      • Making the most of the Automated Brightness Control feature (DIM Mode)
      • Password Setup Page
      • Calibration Page
      • Secondary Connection Page
      • System Connection Page
  • Programming
    • Button Assignments
    • Page Commands
    • Programming Numbers
      • RGB triplets and names for basic 88 colors
      • Font styles and ID numbers
      • Border styles and Programming numbers
    • "^" Button Commands
    • Text Effect Names
    • Button Query Commands
    • Panel Runtime Operations
    • Input Commands
    • Embedded codes
    • Panel Setup Commands
    • Dynamic Image Commands
  • Troubleshooting
  • Appendix
    • Text Formatting Codes for Bargraphs/Joysticks
    • Text Area Input Masking
      • Input mask character types
      • Input mask ranges
      • Input mask next field characters
      • Input mask operations
      • Input mask literals
      • Input mask output examples
    • URL Resources
      • Special escape sequences