Document Outline

• 1 Risks and protections before assembly
• 2 Intended use
• 3 Precautions
• 4 Package content
• 5 Position on farming machine
  • 5.1 System recommended composition
  • 5.2 Monitor and control unit positioning
  • 5.3 Bracket fixing
  • 5.4 Control unit (RCU) fixing
  • 5.5 Control unit position
  • 5.6 Hydraulic unit positioning
• 6 Wiring connections
  • 6.1 General precautions for a correct harness position
  • 6.2 Switch panel connection
  • 6.3 Connecting the Remote Control Units (RCU) (Seletron RCU and hydraulic RCU)
  • 6.4 Securing the Seletron cables
  • 6.5 Hydraulic valve connection
  • 6.6 Sensor connection
  • 6.7 Camera connection
  • 6.8 Power supply connection
  • 6.9 SD memory card
  • 6.10 Pendrive
• 7 Setup
  • 7.1 Setup preparation
  • 7.2 Switching on
  • 7.3 Switching off
  • 7.4 Use of keys for setup
• 8 Menu structure
• 9 Basic settings
• 10 Advanced setup
  • 10.1 Implement
    • 10.1.1 Spray spots configuration
    • 10.1.2 Boom settings
      • • Spray spots spacing
      • • Sections number
      • • Section 1 ÷ 13
    • SECTION MANAGEMENT
      • • Activation status of the sections
    • 10.1.3 Flowmeter
      • • Type
      • • Constant
      • • Minimum flowrate • Maximum flowrate
    • 10.1.4 Filling flowmeter
      • • Type
      • • Constant
      • • Minimum flowrate • Maximum flowrate
    • 10.1.5 Pressure sensor
      • • Activation status
      • • Type
      • • Maximum pressure
    • 10.1.6 Valves
    • MAIN VALVE
      • • Type (REMINDER)
      • • Automatic closing of sections valves (REMINDER)
      • • Automatic closing of main valve
      • • Switching time
    • PRESSURE REGULATING VALVE
      • • Regulation direction
    • SECTION VALVES
      • • Type (REMINDER)
      • • Shut-off time
      • • Switch-on time
    • 10.1.7 Nozzles data
      • • Flowrate • Pressure
      • • Minimum pressure • Maximum pressure
    • 10.1.8 Wheel sensor
      • • Constant
    • 10.1.9 Rev counter
      • • Activation status
      • • Constant
      • • Minimum rotation speed • Maximum rotation speed
    • 10.1.10 Tank
      • • Reserve level
      • • Capacity
      • • Reserve level
      • • Tank profile
    • 10.1.11 Alarms
    • NOZZLES ALARMS
      • • Nozzle wear check
      • • Nozzle wear limit percentage
      • • Minimum pressure alarm • Maximum pressure alarm
    • FLOWMETER ALARMS
      • • Minimum flowrate alarm • Maximum flowrate alarm
    • REV COUNTER ALARMS
      • • Minimum rotation speed alarm • Maximum rotation speed alarm
    • 10.1.12 Working parameters
    • SPRAYING LIMITS
      • • Spraying speed limit
      • • Minimum spraying speed
      • • Regulation pressure limit
      • • Minimum regulation pressure
      • • Flowrate correction factor
      • • Tank level correction factor
    • AUTOMATIC SECTION CONTROL
      • • Sections overlapping limit
      • • Perimeter overlapping limit
      • • Spray closing delay
      • • Spray opening advance
    • GUIDANCE
      • • Steering radius
      • • Reference lines distance offset
    • 10.1.13 Device calibration
    • SELETRON SYSTEM
      • • Identification numbers reset
    • SENSORS
      • • Tank level zero value
      • • Tank profile calibration
      • • Pressure sensor zero value
    • 10.1.14 3-point implement geometry settings (SYSTEM WITH REAR / FRONT 3-POINT HITCH)
      • • Implement upper view
      • • Implement rear view
    • 10.1.15 Towed implement geometry settings (SYSTEM WITH TOWING HITCH)
      • • Implement upper view
      • • Implement rear view
  • 10.2 Tractor
    • 10.2.1 DGPS
    • 10.2.2 PDOP alarm
    • 10.2.3 Tilt compensation
    • 10.2.4 Tilt calibration procedure
    • 10.2.5 Correction type
    • 10.2.6 Receiver advanced data
    • 10.2.7 HDOP alarm
    • 10.2.8 Camera
    • 10.2.9 Tractor geometry settings
      • • Tractor upper view
      • • Tractor rear view
      • • Steering angle
  • 10.3 User
    • ACOUSTIC ALARMS
    • 10.3.1 Acoustic critical alarms
    • 10.3.2 Acoustic low priority alarms
    • 10.3.3 Acoustic info
    • 10.3.4 Steering warning
    • GUIDANCE
    • 10.3.5 Offset tolerance
    • PREFERENCES
    • 10.3.6 Selective job loading
  • 10.4 General options
    • 10.4.1 Language
    • 10.4.2 Units of measurement
    • 10.4.3 Date and time GPS updating
    • 10.4.4 Date and Time
  • 10.5 Device status
    • SELETRON SYSTEM
      • • Status of the Seletron system
    • EXTERNAL SIGNALS
    • POWER SUPPLY DATA
    • FIRMWARE VERSIONS
• 11 Seletron connection
  • 11.1 Preliminary Operations
  • 11.2 Seletron replacement
• 12 Use
  • 12.1 Controls on computer
  • 12.2 Operating switches for control unit valves
    • 12.2.1 "Buffer Zone" function enabled
  • 12.3 Operating switches for hydraulic valves
  • 12.4 Guidance screen
  • 12.5 Spraying a field
• 13 Automatic functions
  • 13.1 Output adjustment
  • 13.2 F2 Automatic adjustment ON/OFF
  • 13.3 Importing and using a prescription map
  • 13.4 How the automatic nozzle selection works (SELETRON system)
  • 13.5 F4 Automatic nozzle selection ON/OFF
  • 13.6 F1/F3/F5/F7 Manual nozzle selection
  • 13.7 Boom section management
  • 13.8 F6 Automatic section control ON/OFF
• 14 "Home" Menu
  • 14.1 F1 Continue last job
  • 14.2 F2 Save job
  • 14.3 F3 New job
  • 14.4 F4 Memories management
    • 14.4.1 Internal memory
      • • Delete
      • • Copy to SD card
      • • Copy to USB pendrive (1 or 2)
    • 14.4.2 SD card
      • • Delete
      • • Copy to internal memory
      • • Remote devices upgrade
    • 14.4.3 USB pendrive
      • • Delete
      • • Copy to internal memory
      • • Remote devices upgrade
    • 14.4.4 Exports
      • • KML on SD
      • • Shape to SD
  • 14.5 F5 Resume job
  • 14.6 F6 Info / Alarms
• 15 Job menu
  • 15.1 F1 Info / Alarms
  • 15.2 F2 Job data
  • 15.3 F3 Tank
  • 15.4 F4 GPS data
  • 15.5 F5 Camera
  • 15.6 F6 Prescription maps
  • 15.7 F7 Zoom all
  • 15.8 F8 Menu
    • 15.8.1 Speed source
      • • GPS
      • • Wheel sensor
      • • GPS and Wheel sensor
      • • Simulation
• 16 Job functions
  • 16.1 F1 Target rate
  • 16.2 F2 Guidance mode
  • 16.3 F3 Point marking
    • 16.3.1 F1 Pause
    • 16.3.2 F3/F5/F7 General point marking
  • 16.4 F4 Surface
  • 16.5 F5 Resume from pause
  • 16.6 F6 Align
  • 16.7 F7 New AB
  • 16.8 F8 Display
    • 16.8.1 F2 Tractor themes
    • 16.8.2 F4 Spraying themes
    • 16.8.3 F6 Daytime/night time display mode
    • 16.8.4 F8 2D/3D display mode
• 17 Maintenance / diagnostics / repairs
  • 17.1 Error messages
  • 17.2 Troubleshooting
  • 17.3 Cleaning rules
• 18 Technical data
  • 18.1 Data and units of measurement shown
• 19 End-of-life disposal
• 20 Guarantee terms