Document Outline

• AXP 1410
• Contents
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Safety Notes
  • System Installation
  • Operation
  • Grounding
  • Connectors and Cabling
  • Expansion and FRU Exchange
  • Laser
  • Environment
  • EMC
  • VCCI
• Sicherheitshinweise
  • System Installation
  • Betrieb
  • Erdung
  • Stecker und Verkabelung
  • Erweiterungen und FRU Austausch
  • Laser
  • Umweltschutz
  • EMV
  • VCCI
• System Overview
  • 1.1 Description
    • 1.1.1 Shelf
    • 1.1.2 Backplane
      • 1.1.2.1 Update Channel Interface
    • 1.1.3 Shelf Manager
    • 1.1.4 Blades
    • 1.1.5 Hub Slots
      • 1.1.5.1 Base Interface
      • 1.1.5.2 Fabric Interface
    • 1.1.6 Rear Transition Modules
    • 1.1.7 Power Entry Modules
    • 1.1.8 Fan Tray Modules
    • 1.1.9 Fan Filter
  • 1.2 Standard Compliances
  • 1.3 Ordering Information
  • 1.4 Product Identification
• Site Preparation
  • 2.1 Overview
  • 2.2 Site Planning Considerations
    • 2.2.1 Receiving and Unpacking the System
    • 2.2.2 Site and Installation Planning
  • 2.3 Requirements
    • 2.3.1 Environmental Requirements
    • 2.3.2 Power Requirements
  • 2.4 Dimensions and Weight
  • 2.5 Mounting Options
  • 2.6 Cooling Considerations
  • 2.7 Acoustic Noise Control
• System Installation
  • 3.1 Overview
  • 3.2 Before Installation
    • 3.2.1 Requirements
    • 3.2.2 Tools You will Need
  • 3.3 Installation
    • 3.3.1 Installing the System in a Rack
    • 3.3.2 Connecting the Cables
      • 3.3.2.1 DC Power Cable
      • 3.3.2.2 Power Cable Termination
      • 3.3.2.3 Connecting the Cables to the PEM
    • 3.3.3 Grounding the System
    • 3.3.4 Powering Up the System
  • 3.4 Powering Down the System
  • 3.5 Emergency Power Off
• FRU Installation
  • 4.1 Installing and Removing Node Blades and RTMs
  • 4.2 Installing and Removing the Shelf Manager Board
    • 4.2.1 Installing the Board
    • 4.2.2 Rotary Switch Settings
    • 4.2.3 Removing the Board
  • 4.3 Replacing Power Entry Modules
    • 4.3.1 Tools You Will Need
    • 4.3.2 Removing the PEM
    • 4.3.3 Installing the PEM
  • 4.4 Installing Fan Tray Modules
    • 4.4.1 Removing the Upper FTM
    • 4.4.2 Installing the Upper FTM
    • 4.4.3 Removing the Lower FTM
    • 4.4.4 Installing the Lower FTM
  • 4.5 Installing a Fan Filter
• Configuring and Operating the System
  • 5.1 Overview
  • 5.2 Network Management
    • 5.2.1 Default VLAN Configuration
    • 5.2.2 Slot Numbers and Slot Addresses
    • 5.2.3 Shelf Address
      • 5.2.3.1 Setting the Shelf Address
      • 5.2.3.2 Shelf Address Reading Behavior
    • 5.2.4 IP Addresses
      • 5.2.4.1 Shelf Manager
      • 5.2.4.2 Hub Blade
      • 5.2.4.3 Node Blades
    • 5.2.5 Restoring Factory Settings
  • 5.3 Accessing System Components
  • 5.4 Software
    • 5.4.1 Installation
    • 5.4.2 Upgrade
  • 5.5 Power Entry Module (PEM)
    • 5.5.1 Description
    • 5.5.2 IPMC Circuitry
  • 5.6 Fan Tray Modules
    • 5.6.1 Description
    • 5.6.2 Cooling Budget
    • 5.6.3 IPMC Circuitry
  • 5.7 Redundancy
    • 5.7.1 Cold Standby
      • 5.7.1.1 Heartbeat
      • 5.7.1.2 Data Replication
      • 5.7.1.3 HPI Interface
    • 5.7.2 System Start-Up Behavior and Dependencies
      • 5.7.2.1 Shelf Manager
      • 5.7.2.2 Hub Blade
      • 5.7.2.3 System Manager
    • 5.7.3 Redundancy Operations
      • 5.7.3.1 Shelf Manager Switchover
      • 5.7.3.2 Shelf Manager Takeover
      • 5.7.3.3 Shelf Manager Failover
      • 5.7.3.4 Shelf Manager Insertion
      • 5.7.3.5 Shelf Manager Extraction
  • 5.8 Blade Insertion and Extraction
    • 5.8.1 Power-On After Blade Insertion
    • 5.8.2 Power-Down Before Blade Extraction
• Supported IPMI Commands
  • 6.1 Introduction
  • 6.2 Standard IPMI Commands
    • 6.2.1 Global IPMI Commands
    • 6.2.2 Event Commands
    • 6.2.3 Sensor Device Commands
    • 6.2.4 FRU Device Commands
  • 6.3 PICMG 3.0 Commands
• FRU Information and Sensor Data Records
  • 7.1 Introduction
  • 7.2 Fan Tray Module Sensor Data Records
    • 7.2.1 Fan Tray Module Sensor Overview
    • 7.2.2 Fan Tray Module Analog Sensors
      • 7.2.2.1 Voltage Sensors
      • 7.2.2.2 Temperature Sensors
      • 7.2.2.3 Fan Speed Sensors
    • 7.2.3 Fan Tray Module Discrete Sensors
      • 7.2.3.1 Hot Swap Sensor
      • 7.2.3.2 IPMB Link Sensor
      • 7.2.3.3 Reserved Sensor
      • 7.2.3.4 OEM-Reserved Sensors
  • 7.3 Power Entry Module Sensor Data Records
    • 7.3.1 PEM FRU Information
    • 7.3.2 E-Keying
    • 7.3.3 Power Configuration
    • 7.3.4 Power Entry Module Sensor Overview
    • 7.3.5 Power Entry Module Analog Sensors
      • 7.3.5.1 Voltage Sensors
      • 7.3.5.2 Current Sensors
      • 7.3.5.3 Temperature Sensor
    • 7.3.6 Power Entry Module Discrete Sensors
      • 7.3.6.1 Hot Swap Sensor
      • 7.3.6.2 IPMB Link Sensor
      • 7.3.6.3 Circuit Breaker State Sensors
• Shelf Management Alarm Module
  • 8.1 Overview
  • 8.2 Payload Hardware
    • 8.2.1 Ethernet Interfaces
    • 8.2.2 Redundancy Interfaces
    • 8.2.3 Block Transfer Interface
    • 8.2.4 Console Interface
  • 8.3 Shelf Management Controller
    • 8.3.1 IPMB0 Interface
    • 8.3.2 IPMC Standard Functions
  • 8.4 Face Plate
  • 8.5 LEDs
  • 8.6 Ethernet Connector (Out-of-Band)
  • 8.7 Alarm Connector
• A Related Documentation
  • A.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • A.2 Related Specifications