Document Outline

• MVME51005E Single Board Computer
• Contents
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Hardware Preparation and Installation
  • 1.1 Introduction
    • 1.1.1 Getting Started
    • 1.1.2 Overview and Equipment Requirements
    • 1.1.3 Unpacking Instructions
  • 1.2 Preparation
    • 1.2.1 Hardware Configuration
    • 1.2.2 Jumper Settings
      • 1.2.2.1 PMC/SBC (761/IPMC) Mode Selection
    • 1.2.3 Installation Considerations
  • 1.3 Installation
    • 1.3.1 PMC Modules
    • 1.3.2 Primary PMCspan
    • 1.3.3 Secondary PMCspan
    • 1.3.4 MVME5100
• Operation
  • 2.1 Introduction
  • 2.2 Switches and Indicators
    • 2.2.1 ABT/RST Switch
      • 2.2.1.1 Abort Function
      • 2.2.1.2 Reset Function
    • 2.2.2 Status Indicators
      • 2.2.2.1 RST Indicator (DS1)
      • 2.2.2.2 CPU Indicator (DS2)
    • 2.2.3 Connectors
      • 2.2.3.1 10/100BASE T Ports
      • 2.2.3.2 DEBUG Port
  • 2.3 System Powerup
    • 2.3.1 Initialization Process
• PPCBug Firmware
  • 3.1 Introduction
  • 3.2 PPCBug Overview
    • 3.2.1 Implementation and Memory Requirements
  • 3.3 Using PPCBug
    • 3.3.1 Hardware and Firmware Initialization
  • 3.4 Default Settings
    • 3.4.1 CNFG - Configure Board Information Block
    • 3.4.2 ENV - Set Environment
      • 3.4.2.1 Configuring the PPCBug Parameters
    • 3.4.3 LED/Serial Startup Diagnostic Codes
    • 3.4.4 Configuring the VMEbus Interface
    • 3.4.5 Firmware Command Buffer
  • 3.5 Standard Commands
    • 3.5.1 Diagnostics
• Functional Description
  • 4.1 Introduction
  • 4.2 Features Summary
  • 4.3 Features Descriptions
    • 4.3.1 General
    • 4.3.2 Processor
    • 4.3.3 System Memory Controller and PCI Host Bridge
    • 4.3.4 Memory
      • 4.3.4.1 Flash Memory
      • 4.3.4.2 ECC SDRAM Memory
    • 4.3.5 P2 Input/Output (I/O) Modes
    • 4.3.6 Input/Output Interfaces
      • 4.3.6.1 Ethernet Interface
      • 4.3.6.2 VMEbus Interface
      • 4.3.6.3 Asynchronous Communications
      • 4.3.6.4 Real-Time Clock & NVRAM & Watchdog Timer
      • 4.3.6.5 Timers
      • 4.3.6.6 Interrupt Routing
      • 4.3.6.7 IDSEL Routing
• RAM500 Memory Expansion Module
  • 5.1 Overview
  • 5.2 Features
  • 5.3 Functional Description
    • 5.3.1 RAM500 Description
    • 5.3.2 SROM
  • 5.4 RAM500 Module Installation
  • 5.5 RAM500 Connectors
    • 5.5.1 Bottom Side Memory Expansion Connector (P1)
  • 5.6 RAM500 Programming Issues
    • 5.6.1 Serial Presence Detect (SPD) Data
• Pin Assignments
  • 6.1 Introduction
    • 6.1.1 Summary
  • 6.2 Jumper Settings
  • 6.3 Connectors
    • 6.3.1 IPMC761 Connector (J3) Pin Assignments
    • 6.3.2 Memory Expansion Connector (J8) Pin Assignments
    • 6.3.3 PCI Expansion Connector (J25) Pin Assignments
    • 6.3.4 PCI Mezzanine Card (PMC) Connectors
    • 6.3.5 VMEbus Connectors P1 & P2 Pin Assignments (PMC mode)
    • 6.3.6 VMEbus P1 & P2 Connector Pin Assignments (SBC Mode)
    • 6.3.7 10 BaseT/100 BaseTx Connector Pin Assignments
    • 6.3.8 COM1 and COM2 Connector Pin Assignments
• Programming the MVME5100
  • 7.1 Introduction
  • 7.2 Memory Maps
    • 7.2.1 Processor Bus Memory Map
      • 7.2.1.1 Default Processor Memory Map
      • 7.2.1.2 Processor Memory Map
      • 7.2.1.3 PCI Memory Map
      • 7.2.1.4 VME Memory Map
    • 7.2.2 PCI Local Bus Memory Map
    • 7.2.3 VMEbus Memory Map
  • 7.3 Programming Considerations
    • 7.3.1 PCI Arbitration
    • 7.3.2 Interrupt Handling
    • 7.3.3 DMA Channels
    • 7.3.4 Sources of Reset
    • 7.3.5 Endian Issues
      • 7.3.5.1 Processor/Memory Domain
      • 7.3.5.2 PCI Domain
      • 7.3.5.3 VMEbus Domain
• A Specifications
  • A.1 General Specifications
  • A.2 Power Requirements
  • A.3 Cooling Requirements
  • A.4 EMC Compliance
• B Troubleshooting
  • B.1 Solving Startup Problems
• C Thermal Analysis
  • C.1 Thermally Significant Components
  • C.2 Component Temperature Measurement
    • C.2.1 Preparation
    • C.2.2 Measuring Junction Temperature
    • C.2.3 Measuring Case Temperature
    • C.2.4 Measuring Local Air Temperature
• D Related Documentation
  • D.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • D.2 Manufacturer’s Documents
  • D.3 Related Specifications