Document Outline

• MVME8100 / MVME8110
• Contents
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Introduction
  • 1.1 Features
  • 1.2 Standard Compliances
  • 1.3 Mechanical Data
  • 1.4 Ordering Information
    • 1.4.1 Supported Board Models
    • 1.4.2 Board Accessories
• Hardware Preparation and Installation
  • 2.1 Overview
  • 2.2 Unpacking and Inspecting the Board
  • 2.3 Requirements
    • 2.3.1 Environmental Requirements
    • 2.3.2 Power Requirements
    • 2.3.3 Thermal Requirements
    • 2.3.4 Thermally Significant Components
    • 2.3.5 Equipment Requirements
  • 2.4 Configuring the Board
    • 2.4.1 Configuration Switches
      • 2.4.1.1 S2 Switch
      • 2.4.1.2 S3 Switch
      • 2.4.1.3 S4 Switch
      • 2.4.1.4 S5 Switch
      • 2.4.1.5 Reset /Abort Switch
  • 2.5 Installing Accessories
    • 2.5.1 Rear Transition Module
    • 2.5.2 PMC/XMC Installation
    • 2.5.3 SATA Installation
  • 2.6 Installing and Removing the Board
  • 2.7 Completing the Installation
• Controls, LEDs, and Connectors
  • 3.1 Overview
  • 3.2 Front Panel
    • 3.2.1 LEDS
      • 3.2.1.1 Front Panel LEDs
    • 3.2.2 Connectors
      • 3.2.2.1 External Connectors
      • 3.2.2.2 On-board Connectors
• Functional Description
  • 4.1 Overview
  • 4.2 Block Diagram
  • 4.3 Processor
  • 4.4 System Memory
  • 4.5 Timers
    • 4.5.1 Real Time Clock
    • 4.5.2 P5020/ P5010 Internal Timers
    • 4.5.3 Watchdog Timers
      • 4.5.3.1 Initial Hardware Watchdog
      • 4.5.3.2 OS Watchdog
    • 4.5.4 CPLD Tick Timer
  • 4.6 Ethernet Interfaces
  • 4.7 SPI Interface
    • 4.7.1 SPI Flash Memory
    • 4.7.2 Firmware Redundancy
  • 4.8 MRAM
  • 4.9 eMMC
  • 4.10 Processor Console Port
  • 4.11 Rear UART Ports
  • 4.12 PCIe Ports
  • 4.13 SRIO Ports
  • 4.14 PMC/XMC Sites
    • 4.14.1 PMC Add-on Card
    • 4.14.2 XMC Add-on Card
  • 4.15 SATA interface
  • 4.16 VME Support
    • 4.16.1 Tsi148 VME Controller
    • 4.16.2 Tsi384 PCIe to PCI/PCI-X Bridge
  • 4.17 USB
  • 4.18 I2C Devices
  • 4.19 Reset/Control CPLD
  • 4.20 Power Management
    • 4.20.1 Power Distribution Structure
    • 4.20.2 Power Sequence Requirements
  • 4.21 Clock Structure
  • 4.22 Reset Structure
  • 4.23 Interrupt Controller Assignments
  • 4.24 GPIO Electrical Characteristics
  • 4.25 Thermal Management
• Boot System
  • 5.1 Overview
  • 5.2 Accessing U-Boot
  • 5.3 Boot Options
    • 5.3.1 Booting from a Network
    • 5.3.2 Booting from an Optional SATA Drive
    • 5.3.3 Booting from a USB Drive
    • 5.3.4 Booting from eMMC
    • 5.3.5 Booting VxWorks Through the Network
  • 5.4 MVME8100 / MVME8110 Specific U-Boot Commands
  • 5.5 Updating U-Boot
• A Battery Exchange
  • A.1 Battery Exchange
• B Related Documentation
  • B.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • B.2 Related Specifications
  • B.3 Manufacturers’ Documents
• Safety Notes
• Sicherheitshinweise