Document Outline

• IntraCore 3624/48
  • 1.1 Features
  • 1.2 System Defaults
  • 1.3 Package Contents
  • 1.4 Front and Back Panel Descriptions
  • 3624 Front Panel
  • 3648 Front Panel
    • 3648 Rear Panel
    • 1.4.1 LEDs
  • 1.5 Management and Configuration
    • 1.5.1 Console Interface
• Chapter 2: Hardware Installation and Setup
  • 2.1 Installation Overview
    • 2.1.1 Safety Overview
    • 2.1.2 Recommended Installation Tools
    • 2.1.3 Power Requirements
    • 2.1.4 Environmental Requirements
    • 2.1.5 Cooling and Airflow
  • 2.2 Installing into an Equipment Rack
    • 2.2.1 Equipment Rack Guidelines
  • 2.3 SFP Mini GBIC Ports
  • 2.4 Connecting Power
  • 2.5 Connecting to the Network
    • 2.5.1 10/100/1000BaseT Ports Cabling Procedures
    • 2.5.2 Gigabit Ethernet Ports Cabling Procedures
• Chapter 3: Initial Software Setup
  • 3.1 Connecting to a Console
  • 3.2 Connecting to a PC
    • 3.3 Username and Password
  • 3.5 Restoring Factory Defaults
• Chapter 4: Understanding the Command Line Interface (CLI)
  • 4.1 User Top (User EXEC) Mode
  • 4.2 Privileged Top (Privileged EXEC) Mode
  • 4.3 Global Configuration Mode
    • 4.3.1 Interface Configuration Mode
  • 4.4 Advanced Features Supported within the Command Mode
  • 4.5 Using CLI Command History
  • 4.6 Using Command-Line Editing Features and Shortcuts
    • 4.6.1 Moving Around on the Command Line
      • Keystrokes
    • 4.6.2 Completing a Partial Command Name
      • Keystrokes
    • 4.6.3 Deleting Entries
      • Keystrokes
  • 5.1 Managing the System
    • 5.1.1 Setting the System Clock
    • 5.1.2 Specify the Hostname
    • 5.1.5 Test Connections with Ping Tests
    • 5.1.3 Enable the System Log
    • 5.1.4 Displaying the Operating Configuration
  • 5.2 Managing Configuration Files
    • 5.2.1 Configuring from the Terminal
    • 5.2.2 Copying Configuration Files to a Network Server
    • 5.2.3 Copying Configuration Files from a Network Server to the Switch
  • 5.3 Managing system image Files
    • 5.3.1 Saving System image to a Network Server
    • 5.3.2 Replacing System image from a Network Server
  • 5.4 Configuring SNMP
    • 5.4.1 Configuring SNMP Support
  • 5.5 Spanning Tree Algorithm
    • 5.5.1 Spanning Tree Parameters
    • 5.5.2 Rapid Spanning Tree Protocol (RSTP)
      • Port Roles and the Active Topology
      • Rapid Convergence
    • 5.5.3 Configuring spanning-tree
      • Enabling/Disabling Spanning-tree
      • Configuring Switch/Bridge Priority
      • Configuring Link Type
      • Configuring an Edge Port
      • Configuring Port Path Cost
      • Configuring Port Priority
• Chapter 6: Configuring IP
  • 6.1 Establish Address Resolution
  • 6.2 Managing IP Multicast Traffic
    • 6.2.1 IGMP Overview
      • Forwarding Unknown Multicast Packets. Unknown multicast packets are those packets with destination IP multicast addresses not learned by the switch. By default, the switch forwards all such traffic.
    • 6.2.2 Configuring IGMP
      • Enable the IGMP Snooping
      • Enable the IGMP querier
      • Modifying the IGMP Host-Query Message Interval
      • Changing the Maximum Query Response Time
• 6.3 Access Lists
  • 6.3.1 Creating an Access List
  • 6.3.2 Configuring an Access List
  • 6.3.3 Applying an Access List to an Interface
  • 6.3.4 Enabling an Access List
• Chapter 7: VLAN Configuration
  • 7.1 Creating or Modifying a VLAN
  • VLANS can be configured using the following commands:
  • 7.2 VLAN Port Membership
    • 7.2.1 configuring vlan ports
    • 7.2.2 Trunk (IEEE 802.1q)
  • 8.1 Scheduling algorithm
    • 8.1.1 Configuring Weighted Round Robin
      • Queue Weight
    • 8.1.2 Monitoring Weighted Round Robin
  • 8.2 Priority Queuing
    • 8.2.1 Priority Mapping
      • Priorities Queues
    • 8.2.2 Port Based QOS
    • 8.2.3 802.1P Based QOS
    • 8.2.4 IP Based QOS
  • 8.3 Traffic Shaping
    • 8.3.1 Configuring Traffic Shaping for an Interface
  • 8.4 Rate Limiting
• Chapter 9: Configuring the Switch Using the GUI
  • 9.1 Main Configuration Menu
  • 9.2 System
    • 9.2.3 System Time Setting
    • Use the Time Setting page to set the time zone or local time for the switch. Daylight savings can also be enabled. Click the “Save Settings” button when done.
  • Port Management – Port Config - Specific Port. Settings can be made on a per port basis. When a port number is clicked the subscreen appears.
  • Port Management – LAG Group. Click on a group number to set the groups properties.
  • VLAN MANAGEMENT – VLAN SETTINGS. With a vlan selected, ports can be marked as tagged, or untagged. Lover on the screen, LAG groups can also be tagged or untagged. Click Save Settings when done.
• MSTP. Multiple Spanning Tree Protocol can be enabled on this page.
  • SNMP Continued
  • ADMIN Continued – assorted administration functions are controlled using the next several screens.
• Chapter 10: CLI Commands
• Appendix A: Basic Troubleshooting
• Appendix C: FCC Compliance and Warranty Statements
  • C.1 FCC Compliance Statement
  • C.2 Important Safety Instructions
  • C.3 IntraCore Warranty Statement