Document Outline

• IC39480-IC39240_user_manual-01
• IC39480-IC39240_user_manual
  • IntraCore 39240/480
    • 1.1 Features
    • 1.2 System Defaults
    • 1.3 Package Contents
    • 1.4 Front and Back Panel Descriptions
    • 39240 Front Panel
    • 39480 Front Panel
      • 39480 Rear Panel
      • 1.4.1 LEDs
    • 1.5 Management and Configuration
      • 1.5.1 Console Interface
  • Chapter 2: Hardware Installation and Setup
    • 2.1 Installation Overview
      • 2.1.1 Safety Overview
      • 2.1.2 Recommended Installation Tools
      • 2.1.3 Power Requirements
      • 2.1.4 Environmental Requirements
      • 2.1.5 Cooling and Airflow
    • 2.2 Installing into an Equipment Rack
      • 2.2.1 Equipment Rack Guidelines
    • 2.3 SFP Mini GBIC Ports
    • 2.4 Connecting Power
    • 2.5 Connecting to the Network
      • 2.5.1 10/100/1000BaseT Ports Cabling Procedures
      • 2.5.2 Gigabit Ethernet Ports Cabling Procedures
  • Chapter 3: Initial Software Setup
    • 3.1 Connecting to a Console
    • 3.2 Connecting to a PC
      • 3.3 Username and Password
    • 3.5 Restoring Factory Defaults
  • Chapter 4: Understanding the Command Line Interface (CLI)
    • 4.1 User Top (User EXEC) Mode
    • 4.2 Privileged Top (Privileged EXEC) Mode
    • 4.3 Global Configuration Mode
      • 4.3.1 Interface Configuration Mode
    • 4.4 Advanced Features Supported within the Command Mode
    • 4.5 Using CLI Command History
    • 4.6 Using Command-Line Editing Features and Shortcuts
      • 4.6.1 Moving Around on the Command Line
        • Keystrokes
      • 4.6.2 Completing a Partial Command Name
        • Keystrokes
      • 4.6.3 Deleting Entries
        • Keystrokes
    • 5.1 Managing the System
      • 5.1.1 Setting the System Clock
      • 5.1.2 Specify the Hostname
      • 5.1.5 Test Connections with Ping Tests
      • 5.1.3 Enable the System Log
      • 5.1.4 Displaying the Operating Configuration
    • 5.2 Managing Configuration Files
      • 5.2.1 Configuring from the Terminal
      • 5.2.2 Copying Configuration Files to a Network Server
      • 5.2.3 Copying Configuration Files from a Network Server to the Switch
    • 5.3 Managing system image Files
      • 5.3.1 Saving System image to a Network Server
      • 5.3.2 Replacing System image from a Network Server
    • 5.4 Configuring SNMP
      • 5.4.1 Configuring SNMP Support
    • 5.5 Spanning Tree Algorithm
      • 5.5.1 Spanning Tree Parameters
      • 5.5.2 Rapid Spanning Tree Protocol (RSTP)
        • Port Roles and the Active Topology
        • Rapid Convergence
      • 5.5.3 Configuring spanning-tree
        • Enabling/Disabling Spanning-tree
        • Configuring Switch/Bridge Priority
        • Configuring Link Type
        • Configuring an Edge Port
        • Configuring Port Path Cost
        • Configuring Port Priority
  • Chapter 6: Configuring IP
    • 6.1 Establish Address Resolution
    • 6.2 Managing IP Multicast Traffic
      • 6.2.1 IGMP Overview
        • Forwarding Unknown Multicast Packets. Unknown multicast packets are those packets with destination IP multicast addresses not learned by the switch. By default, the switch forwards all such traffic.
      • 6.2.2 Configuring IGMP
        • Enable the IGMP Snooping
        • Enable the IGMP querier
        • Modifying the IGMP Host-Query Message Interval
        • Changing the Maximum Query Response Time
  • 6.3 Access Lists
    • 6.3.1 Creating an Access List
    • 6.3.2 Configuring an Access List
    • 6.3.3 Applying an Access List to an Interface
    • 6.3.4 Enabling an Access List
  • Chapter 7: VLAN Configuration
    • 7.1 Creating or Modifying a VLAN
    • VLANS can be configured using the following commands:
    • 7.2 VLAN Port Membership
      • 7.2.1 configuring vlan ports
      • 7.2.2 Trunk (IEEE 802.1q)
  • Chapter 8: Quality of Service Configuration
    • 8.1 Scheduling algorithm
      • 8.1.1 Configuring Weighted Round Robin
        • Queue Weight
      • 8.1.2 Monitoring Weighted Round Robin
    • 8.2 Priority Queuing
      • 8.2.1 Priority Mapping
        • Priorities Queues
      • 8.2.2 Port Based QOS
      • 8.2.3 802.1P Based QOS
      • 8.2.4 IP Based QOS
    • 8.3 Traffic Shaping
      • 8.3.1 Configuring Traffic Shaping for an Interface
    • 8.4 Rate Limiting
  • Chapter 9: Configuring the Switch Using the GUI
    • 9.1 Main Configuration Menu
    • 9.2 System
      • 9.2.3 System Time Setting
      • Use the Time Setting page to set the time zone or local time for the switch. Daylight savings can also be enabled. Click the “Save Settings” button when done.
    • Port Management – Port Config - Specific Port. Settings can be made on a per port basis. When a port number is clicked the subscreen appears.
    • Port Management – LAG Group. Click on a group number to set the groups properties.
    • VLAN MANAGEMENT – VLAN SETTINGS. With a vlan selected, ports can be marked as tagged, or untagged. Lover on the screen, LAG groups can also be tagged or untagged. Click Save Settings when done.
  • MSTP. Multiple Spanning Tree Protocol can be enabled on this page.
    • SNMP Continued
    • ADMIN Continued – assorted administration functions are controlled using the next several screens.
  • Chapter 10: CLI Commands
  • Appendix A: Basic Troubleshooting
  • Appendix B: Specifications
  • Appendix C: FCC Compliance and Warranty Statements
    • C.1 FCC Compliance Statement
    • C.2 Important Safety Instructions
    • C.3 IntraCore Warranty Statement