Document Outline

• Published by
• Introduction
• Packaging
• Modes of Operation
  • TCP Server Mode
    • TCP Client Mode
    • UDP Mode
    • Tunneling Mode
• Hardware Description
  • SE5002 Interfaces and DIN-Rail Mounting settings
• LED Status
  • LAN
  • Installation Procedures:
• Software
  • Configuration by SerialManager
    • Configuring the static IP with SerialManager
    • Static IP dialog window
    • SerialManager Auto IP Dialog Window
  • Configuration by Telnet utility:
    • Telnet to the system
    • System main menu
    • System configuring using Telnet
    • Network configuring using Telnet
    • changing password using Telnet
    • Com1 setup
    • Link Mode-TCP server setup
    • Link Mode-TCP client setup
    • Link Mode-UDP client setup
    • Com port setting
    • Com port-Enabling serial data buffer
    • Setting packet delimiter timer
    • Setting packet delimiter-character pattern
  • 3.3 Configuring Using Web Browser
    • 3.3.1 Log in
    • login the system via Web
    • Overview
    • 3.3.2 Changing password
    • Change the password
    • 3.3.3 Networking
    • Network setup
    • 3.3.4 Configuring SE5002 as TCP server：
    • Com1 setup-TCP server
    • 3.3.5 Configuring SE5002 as TCP client：
    • Com1 setup-TCP client
    • 3.3.6 Pair Connection(Tunneling Mode)
    • Com1 setup –pair connection
    • 3.3.7 Configuring SE5002 in UDP mode：
    • Com 1 setup –UDP mode
    • Configuration successfully updated
    • Data Transmission in a UDP Master(Client) Mode
    • Data Transmission in a UDP Slave(server) Mode
  • 3.4 Assigning new IP Address with ARP commands
    • Ms-DOS command prompt window: add host computer IP to ARP ta
    • Assigning a new IP address with ARP command
• 4. Using Virtual COM
  • Virtual Com connection diagram
  • 4.1 Setup of a virtual COM driver
    • PC requirements
    • 4.1.2 Cautions on Use
    • 4.1.3 Limitation
    • 4.1.4 Installation
    • 4.1.5 Uninstalling
  • 4.2 Virtual COM communications
    • 4.2.1 Enabling Virtual COM on SE5002
    • Enabling Virtual COM port
    • Enabling Virtual COM port via Telnet
    • 4.2.2 Running Serial/IP on PC
    • Serial/IP for Atop control panel
  • 4.3 Configuring Virtual COM Ports
    • Configuration Wizard
• 5. SNMP Setup
  • 5.1 SNMP Network Management Platform
  • 5.2 Using NetworkView: An Example
    • IP address searching
    • Searching progress
    • NetworkView display the devices found
    • NetworkView display device information
  • 6.1 Preparing System
  • 6.2 Running Sample Program
    • 6.2.1 TCPTEST in Visual Basic
    • 6.2.2 TCPTEST2 in Visual C
    • TCPTEST2 IP_Address Port_Number
• Diagnostics
  • 7.1 Using Standard TCP/IP Utility ping Command
  • 7.3 Using TCPTEST.EXE or TCPTEST2.EXE Sample Program
• Appendix A: Specification
  • A.1. Hardware Specification
  • A.2. Software Specification
  • A.3 Panel Layout and Connector Pin Assignments
  • A.3.1. Panel Layout
    • A.3.2.1 DB9 Pin Assignments
    • A.3.2.2 Terminal Block Pin Assignments
    • A.3.3 Ethernet Port (RJ-45) Pin Assignments
    • Note: Device will not be damage if the polarity is reverse.
    • A.4 Buzzer/LED Message
    • A.4.1 Buzzer
    • A.4.2 LAN
    • A.4.3 COM Port
    • A.4.4 RUN
• Appendix B: Upgrade System Firmware
  • B.2 Critical Issues
  • B.3 Error Messages
• Appendix C: Re-loading System Firmware
• Appendix D: Using SerialManager