Document Outline

• Table of contents
• 1. Safety instructions
  • 1.1 Range of application
  • 1.2 Electrical connection
  • 1.3 Maintenance
  • 1.4 Warnings and notes
• 2. Short description
• 3. Technical data
• 4. Additional information to the wiring diagram legend
• 5. Transport, storage and packaging
  • 5.1 Transport
  • 5.2 Storage
  • 5.3 Packaging
• 6. Mounting to valve/ gearbox
• 7. Mounting positions of the local controls
• 8. Electrical connection
  • 8.1 Connection with AUMA plug/ socket connector (S, SH, SE)
• 9. Manual operation
• 10. Operation and indications of the local controls
• 11. Opening the switch compartment
  • 11.1 Removing the cover from the switch compartment
  • 11.2 Pulling off the indicator disc (option)
• 12. Setting the limit switching
  • 12.1 Setting end position CLOSED (black section)
  • 12.2 Setting end position OPEN (white section)
  • 12.3 Checking the limit switches
• 13. Setting the DUO limit switching (option)
  • 13.1 Setting direction CLOSE (black section) .Move valve
  • 13.2 Setting direction OPEN (white section)
  • 13.3 Checking the DUO limit switches
• 14. Setting the torque switching
  • 14.1 Setting
  • 14.2 Checking the torque switches
• 15. Test run
  • 15.1 Checking the direction of rotation
  • 15.2 Checking the setting of the limit switching
  • 15.3 Checking the type of seating
  • 15.4 Checking the PTC tripping device (option)
• 16. Setting the potentiometer (option)
• 17. Setting the electronic position transmitter RWG (option)
  • 17.1 Setting 2-wire system 4 – 20 mA and 3- /4-wire system 0 – 20 mA
  • 17.2 Setting 3- / 4- wire system 4 – 20 mA
• 18. Setting the mechanical position indicator (option)
• 19. Closing the switch compartment
• 20. Actuator controls AUMA MATIC
  • 20.1 Functions of the diagnosis LEDs on the interface board (standard version)
  • 20.2 Programming the logic board
  • 20.3 EMERGENCY - OPEN and EMERGENCY - CLOSE signal (option)
• 21. Electronic positioner (option)
  • 21.1 Technical data
  • 21.2 Setting
    • 21.2.1 Setting type of signal
    • 21.2.2 Setting actuator behavior on loss of signal
  • 21.3 Positioner adjustment for end position CLOSED (standard version)
  • 21.4 Positioner adjustment for end position OPEN (standard version)
  • 21.5 Setting the sensitivity
  • 21.6 Positioner adjustment for end position OPEN (inverse operation)
  • 21.7 Positioner adjustment end position CLOSED (inverse operation)
  • 21.8 Positioner in Split Range version (option)
    • 21.8.1 Split Range: description of functions
    • 21.8.2 Programming
    • 21.8.3 Positioner adjustment for Split Range
• 22. Timer (option)
  • 22.1 Functions of the diagnosis LEDs (timer)
  • 22.2 Setting start and end of stepping mode via DUO limit switching (option)
  • 22.3 Setting ON and OFF times
• 23. Fuses
  • 23.1 Fuses within the actuator controls
  • 23.2 Motor protection
• 24. Enclosure protection IP 68 (option)
• 25. Maintenance
• 26. Lubrication
• 27. Disposal and recycling
• 28. Service
• 29. Spare parts list Multi-turn actuator SA 07.1 – SA 16.1/SAR 07.1 – SAR 16.1
• 30. Spare parts list controls AUMA MATIC
• Index
  • A
    • Ambient temperature 8
  • B
    • Blinker transmitter 35
  • C
    • Collective fault signal 34,35
    • Command signal 37,39,40
    • Corrosion protection 10,56
    • Cross sections 18
    • Current consumption 6,15
  • D
    • Direction of rotation 26
    • Disconnect switches 15
    • Disposal and recycling 56
    • DUO limit switching 24
  • E
    • Electrical connection 15
    • Electronic position transmitter RWG 30
      • 2-wire system 31
      • 3-/ 4-wire system 32
    • EMERGENCY signal 36
    • Enclosure protection IP 68 55
  • F
    • Finish machining of the stem nut 13
    • Fuses 52
  • H
    • Handwheel 19
    • Heater 15
  • I
    • Indicator disc 22,33
    • Interface board 34
    • Internet 5
    • Inverse operation 45,46
  • L
    • Limit switching 23,24,27
    • Local controls 27
    • Logic board 35
    • Loss of signal 40
    • Lubrication 56
  • M
    • Mains frequency 6
    • Maintenance 4
    • Manual operation 19
    • Mechanical position indicator 33
    • Motor protection 54
    • Mounting positions of the local controls 14
    • Mounting to valve/ gearbox 12
  • N
    • Name plate 61
  • O
    • Output drive types 12
    • Overvoltage category 6
  • P
    • Packaging 10
    • Pause time 37,51
    • Position indicator 33
    • Position transmitter RWG 15,30
    • Positioner 37
    • Potentiometer 29
    • Power supply 6
    • Protection tube 13
    • Protective earth 18
    • PTC thermistors 54
    • PTC tripping device 27
    • Push-to-run operation 21,35
  • R
    • Rate power 6
    • Remote indication 29,30
    • RESET (Selector switch position) 27
    • Running time 37,51
  • S
    • Safety instructions 4
    • Selector switch 27
    • Self-retaining 21,35
    • Sensitivity 43
    • Service 57
    • Short description 5
    • Short-circuit protection 15
    • Signals 9
    • Spare parts list 59
      • Multi-turn actuator 59
      • Controls 61
    • Split Range Version 47
    • Stepping mode
      • Operating time 49
      • Pause time 51
    • Storage 10
  • T
    • Technical data 6
    • TEST (Selector switch position) 27
    • Test run 26
    • Thermoswitches 54
    • Timer 49
    • Torque setting 25
    • Transport 10
    • Tripping torque 25
    • Type of duty 6
    • Type of seating 35
  • W
    • Wall bracket 16