Document Outline

• toc
  • 1. Packaging
    • 1.1 Unpacking
  • 2. Installation guidelines
    • 2.1 Safety warnings
    • 2.2 Installation guidelines
  • 3. Installation
    • 3.1 Battery installation in the RCU
    • 3.2 Lens installation
    • 3.3 Removing the lens
    • 3.4 Lens range
    • 3.5 Lens Formulas
    • 3.6 Projector configuration
    • 3.7 Positioning the projector
  • 4. Connections
    • 4.1 Power connection
    • 4.2 Signal connections
      • 4.2.1 The input section
      • 4.2.2 Connecting a Composite video signal
      • 4.2.3 Connecting an S-Video signal
      • 4.2.4 Connecting an RGB signal
      • 4.2.5 Connecting a Component Video signal
      • 4.2.6 Connecting a DVI signal
      • 4.2.7 Connecting a computer signal
      • 4.2.8 The DVI output
    • 4.3 Communication connections
      • 4.3.1 RS232/RS422 Connections
      • 4.3.2 Ethernet Connections
  • 5. Setup
    • 5.1 RCU & Local keypad
    • 5.2 Terminology overview
    • 5.3 Switching on
    • 5.4 Setting up the RCU address
    • 5.5 Setting up the projector address (only if necessary)
    • 5.6 Setting up the orientation
    • 5.7 Adjusting the lens
    • 5.8 Setup the baudrate for serial communication
    • 5.9 Network settings
    • 5.10 Preferences
      • 5.10.1 Language setting
      • 5.10.2 Automatic startup
  • 6. Getting started
    • 6.1 Start up
    • 6.2 Selecting a source
    • 6.3 Adjusting the image
  • 7. Advanced
    • 7.1 The OSD Menu
    • 7.2 Using the Dialog boxes
    • 7.3 Source selection
      • 7.3.1 Source selection
      • 7.3.2 Composite video
      • 7.3.3 S-Video
      • 7.3.4 RGB-YUV
      • 7.3.5 PC
      • 7.3.6 DVI
    • 7.4 General
      • 7.4.1 Pause
      • 7.4.2 Freeze
      • 7.4.3 Identification
    • 7.5 Image
      • 7.5.1 Image settings
        • 7.5.1.1 Setting the Contrast
        • 7.5.1.2 Setting the Brightness
        • 7.5.1.3 Color
        • 7.5.1.4 Tint (NTSC video signals only)
        • 7.5.1.5 Sharpness
        • 7.5.1.6 Gamma
        • 7.5.1.7 Phase (RGB signals only)
        • 7.5.1.8 Noise Reduction (only for video signals)
      • 7.5.2 Aspect ratio
      • 7.5.3 Color temperature
      • 7.5.4 Film mode detection (video only)
      • 7.5.5 Input balance
      • 7.5.6 Automatic gain control (AGC)
      • 7.5.7 Manual gain control
    • 7.6 Lamp management
      • 7.6.1 Runtimes
      • 7.6.2 Lamp mode
      • 7.6.3 History
      • 7.6.4 Reset lamp Runtime
      • 7.6.5 Clear lamp error
      • 7.6.6 Lamp runtime warning
    • 7.7 Image files
      • 7.7.1 Introduction to Image files
      • 7.7.2 Load file
      • 7.7.3 Forced file load
      • 7.7.4 Auto Image
      • 7.7.5 Edit file
      • 7.7.6 Save as (create a custom file)
      • 7.7.7 Rename file
      • 7.7.8 Copy
      • 7.7.9 Delete
    • 7.8 Display setup
      • 7.8.1 Dynacolor™
      • 7.8.2 Brilliant Color TM mode
      • 7.8.3 Full screen synchronous representation
      • 7.8.4 Text box
      • 7.8.5 Menu bar position
      • 7.8.6 Status bar position
      • 7.8.7 Sliderbox position
      • 7.8.8 Softedge
        • 7.8.8.1 Softedge Border
        • 7.8.8.2 Black level
  • 8. Maintenance
    • 8.1 Cleaning the lens
  • 9. Image files
    • 9.1 Image files
  • 10. Troubleshooting
    • 10.1 Using the OSD