Document Outline

• 1.0 INTRODUCTION
  • 1.1 Shipping Damage
  • 1.2 Package Contents
  • 1.3 Additional Requirements
  • 1.4 Copyright Notice
  • 1.5 General
    • 1.5.1 BUILDING POINTS TO BE MONITORED:
    • 1.5.2 WALLMOUNT POINTS TO BE MONITORED FOR EACH UNIT:
    • 1.5.3 BUILDING POINTS TO BE CONTROLLED:
    • 1.5.4 SYSTEM POINTS TO BE CONTROLLED:
    • 1.5.5 WALLMOUNT POINTS TO BE CONTROLLED:
    • 1.5.6 ALARM POINTS:
  • 1.6 Model Nomenclature
• 2.0 SPECIFICATIONS
  • 2.1 Electrical Specifications
  • 2.2 Mechanical Specifications
  • 2.3 Environmental Specifications
  • 2.4 Sensor Specifications
    • 2.4.1 TEMPERATURE SENSORS
    • 2.4.2 HUMIDITY SENSORS
    • 2.4.3 COMPRESSOR CURRENT SENSOR
    • 2.4.4 DIRTY FILTER SENSOR
    • 2.4.5 BLOWER AIRFLOW SWITCH
• 3.0 INSTALLATION
  • 3.1 Mounting
  • 3.2 Wiring
    • 3.2.1 HIGH VOLTAGE WIRING
    • 3.2.2 WIRING - LOW VOLTAGE
    • 3.2.3 WIRING - SENSORS
      • 3.2.3.1 Outdoor Temperature Sensor (OTS)
      • 3.2.3.2 Outdoor Humidity Sensor (OHS)
      • 3.2.3.3 Zone Temperature Sensor (ZTS)
      • 3.2.3.4 Zone Humidity Sensor (ZHS) (Optional)
    • 3.2.4 WIRING – INPUTS & OUTPUTS
      • 3.2.4.1 Shelter Alarm Output
      • 3.2.4.2 Power Transfer Switch Output (PTS)
      • 3.2.4.3 Power Failure Sense Input
      • 3.2.4.4 Fire Alarm Input
      • 3.2.4.5 Fire Trouble Input
      • 3.2.4.6 Door Alarm Input
    • 3.2.5 WIRING - TELEPHONE LINE
    • 3.2.6 WIRING - ETHERNET
  • 3.3 Installation Check List
  • 3.4 System Startup
    • 3.4.1 WALLMOUNT STARTUP CHECKLIST
    • 3.4.2 TCS22 STARTUP CHECKLIST
• 4.0 OPERATION
  • 4.1 General
  • 4.2 Sequence of Operation
    • 4.2.1 COOLING SEQUENCE WITH ECONOMIZERS
    • 4.2.2 HEATING SEQUENCE
    • 4.2.3 FAN SEQUENCE
    • 4.2.4 OCCUPIED / UNOCCUPIED MODE SEQUENCE
    • 4.2.5 ALARM SEQUENCE
    • 4.2.6 DEHUMIDIFICATION SEQUENCE
    • 4.2.7 THERMAL SHOCK PROTECTION SEQUENCE
    • 4.2.8 MODEM SEQUENCE
    • 4.2.9 POWER MANAGEMENT SEQUENCE
    • 4.2.10 SETPOINTS
• 5.0 DISPLAY & KEYPAD OPERATION (DAK)
  • 5.1 Display & Keypad Physicals
  • 5.2 Power Up
  • 5.3 Menu Tree
  • 5.3.1 Buildings Status Screen
    • 5.3.1.1 ROOM TEMPERATURE
    • 5.3.1.2 ROOM HUMIDITY
    • 5.3.1.3 OUTDOOR TEMPERATURE
    • 5.3.1.4 OUTDOOR HUMIDITY
    • 5.3.1.5 ACTIVE COOLING SETPOINT
    • 5.3.1.6 ACTIVE HEATING SETPOINT
    • 5.3.1.7 FREE COOLING ON / OFF
    • 5.3.1.8 ROOM OCCUPIED YES/NO
    • 5.3.1.9 OUTDOOR ENTHALPY
  • 5.3.2 Unit Status Screen
    • 5.3.2.1 UNIT #1 ECONOMIZER
    • 5.3.2.2 UNIT #1 COMPRESSOR
    • 5.3.2.3 UNIT #1 HEATER
    • 5.3.2.4 UNIT #1 BLOWER
    • 5.3.2.5 UNIT #1 FILTER
    • 5.3.2.6 UNIT #1 DISCHARGE AIR TEMPERATURE
  • 5.3.3 Alarms Menu
    • 5.3.3.1 SPACE TEMP ALARM
    • 5.3.3.2 SPACE HUMIDITY ALARM
    • 5.3.3.4 #1 COMPRESSOR ALARM
    • 5.3.3.5 #1 FILTER ALARM
    • 5.3.3.6 UTILITY POWER FAIL
    • 5.3.3.7 FIRE TROUBLE
    • 5.3.3.8 FIRE ALARM
    • 5.3.3.9 OUTDOOR TEMP ALARM
    • 5.3.3.10 OUTDOOR HUMIDITY ALARM
    • 5.3.3.11 DOOR ALARM
  • 5.3.4 Setpoints Screen
    • 5.3.4.1 OCCUPIED COOLING SETPOINT
    • 5.3.4.2 UNOCCUPIED COOLING SETPOINT
    • 5.3.4.3 OCCUPIED HEATING SETPOINT
    • 5.3.4.4 UNOCCUPIED HEATING SETPOINT
    • 5.3.4.5 HIGH TEMPERATURE ALARM SETPOINT
    • 5.3.4.6 LOW TEMPERATURE ALARM SETPOINT
    • 5.3.4.7 HIGH HUMIDITY ALARM SETPOINT
    • 5.3.4.8 LOW HUMIDITY ALARM SETPOINT
    • 5.3.4.9 DEHUMIDIFICATION SETPOINT
    • 5.3.4.10 FREE COOLING ENTHALPY SETPOINT
    • 5.3.4.11 FREE COOLING DRY BULB SETPOINT
  • 5.3.5 Overrides Unit #1 Screen
    • 5.3.5.1 #1 BLOWER OVERRIDE
    • 5.3.5.2 #1 ECONOMIZER OVERRIDE
    • 5.3.5.3 #1 COMPRESSOR OVERRIDE
    • 5.3.5.4 #1 HEATER OVERRIDE
    • 5.3.5.5 CONTINUOUS BLOWER
  • 5.3.6 Enables Menu
    • 5.3.6.1 ECONOMIZER OPERATION
    • 5.3.6.2 FREE COOLING ENTHALPY CHANGEOVER
    • 5.3.6.3 DRY BULB TEMPERATURE CHANGEOVER
    • 5.3.6.4 DAYLIGHT SAVINGS TIME
    • 5.3.6.5 50HZ CLOCK
    • 5.3.6.6 ZONE HUMIDITY SENSOR
      • 5.3.6.7 Zone Dehumidification
  • 5.3.7 Password Operation
    • • 5.3.7.1 Entering Password
  • 5.4 Keyboard Map
• 6.0 PC SOFTWARE OPERATION
  • 6.1 ClimateWatch System Software Overview
  • 6.2 Installation
    • 6.2.1 HARDWARE REQUIREMENTS
    • 6.2.2 SOFTWARE INSTALLATION
  • 6.3 ASI Expert / Bard ClimateWatch Software
    • 6.3.1 SCREEN OVERVIEW
      • 6.3.1.1 Menu Bar
      • 6.3.1.2 Tool Bar
      • 6.3.1.3 Status Bar
      • 6.3.1.4 Controller Information Area
      • 6.3.1.5 Project Folders
    • 6.3.2 TCS COMMUNICATIONS
      • 6.3.2.1 Software Setup
      • 6.3.2.2 Creating a New Project & Establishing Communications
      • 6.3.2.3 Direct Connection
      • 6.3.2.4 Remote Connection
      • 6.3.2.5 Downloading Controller Information
      • 6.3.2.6 Saving TCS Configuration
      • 6.3.2.7 Loading TCS Configuration.
  • 6.4 TCS Controller Information Screens
    • 6.4.1 MAIN SCREEN TAB
      • 6.4.1.1 Conditions
      • 6.4.1.2 Unit #1 Status
      • 6.4.1.3 Unit #2 Status
      • 6.4.1.4 Time & Place
    • 6.4.2 SET POINT TAB
      • 6.4.2.1 Occupied Cooling Setpoint
      • 6.4.2.2 Unoccupied Cooling Setpoint
      • 6.4.2.3 Occupied Heating Setpoint
      • 6.4.2.4 Unoccupied Heating Setpoint
      • 6.4.2.5 High Temperature Alarm SetPoint
      • 6.4.2.6 Low Temperature Alarm SetPoint
      • 6.4.2.7 High Humidity Alarm SetPoint
      • 6.4.2.8 Low Humidity Alarm SetPoint
      • 6.4.2.9 Enthalpy Changeover Setpoint
      • 6.4.2.10 Dry Bulb Changeover Setpoint
      • 6.4.2.11 Dehumidification Setpoint
      • 6.4.2.12 Continuous Blower Enable
      • 6.4.2.13 Active Cooling Setpoint
      • 6.4.2.14 Active Heating Setpoint
      • 6.4.2.15 Active Dehumidification Setpoint
      • 6.4.2.16 Stage Indicators
    • 6.4.3 OVERRIDE #1 TAB
      • 6.4.3.1 Unit #1 Compressor
      • 6.4.3.2 Unit #1 Blower
      • 6.4.3.3 Unit #1 Economizer
      • 6.4.3.4 Unit #1 Heater
    • 6.4.4 ALARMS TAB
      • 6.4.4.1 Unit #1 Filter Alarm
      • 6.4.4.2 Unit #1 Compressor Alarm
      • 6.4.4.3 Unit #1 Blower Alarm
      • 6.4.4.4 Zone Temperature Alarm
      • 6.4.4.5 Zone Humidity Alarm
      • 6.4.4.6 Outdoor Temperature Alarm
      • 6.4.4.7 Outdoor Humidity Alarm
      • 6.4.4.8 Main Power Alarm
      • 6.4.4.9 Fire Alarm
      • 6.4.4.10 Fire Trouble Alarm
      • 6.4.4.11 Door Alarm
    • 6.4.5 ALARM LOG TAB
    • 6.4.6 OFFSETS TAB
      • 6.4.6.1 Zone Temperature Offset
      • 6.4.6.2 Zone Humidity Offset
      • 6.4.6.3 Outdoor Temperature Offset
      • 6.4.6.4 Outdoor Humidity Offset
      • 6.4.6.5 Unit #1 Supply Air Temperature Offset
    • 6.4.7 MISC. TAB
      • 6.4.7.1 Clear Alarm Event Log
      • 6.4.7.2 Enable Economizer Operation.
      • 6.4.7.3 Economizer Changeover Scheme
      • 6.4.7.4 Enable Daylight Savings Time
      • 6.4.7.5 Enable 50 hz Clock
      • 6.4.7.6 Enable Zone Humidity Sensor
      • 6.4.7.7 Enable Zone Dehumidification
      • 6.4.7.8 Model Number
      • 6.4.7.9 Model Serial Number
      • 6.4.7.10 Software
      • 6.4.7.11 Firmware
    • 6.4.8 TREND TAB
    • 6.4.9 DIAL OUT TAB
    • 6.4.10 NOTES TAB
• 7. MAINTENANCE & TROUBLESHOOTING
  • 7.1 Routine Maintenance
  • 7.2 Troubleshooting
    • 7.2.1 TCS22 TROUBLESHOOTING
    • 7.2.2 WALLMOUNT QUICK TROUBLESHOOTING GUIDE.