BECKHOFF ET1100 Instruction Manuals and User Guides
We have 2 Instruction Manuals and User Guides for ET1100 BECKHOFF
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 119 |
| Size: | 1.98 MB |
Show table of contents
Read manual
Document Outline
- Section III – Hardware Description
- 1 Overview
- 2 Features and Registers
- 3 Pin Description
- 3.1 Overview
- 3.2 Configuration Pins
- 3.3 General ET1100 Pins
- 3.4 SII EEPROM Interface Pins
- 3.5 MII Management Pins
- 3.6 Distributed Clocks SYNC/LATCH Pins
- 3.7 LED Signals
- 3.8 Physical Ports and PDI Pins
- 3.9 PDI Signal Pinout depending on selected PDI
- 3.10 Power Supply
- 3.11 Reserved Pins
- 4 MII Interface
- 5 EBUS/LVDS Interface
- 6 PDI description
- 6.1 PDI Deactivated
- 6.2 Digital I/O Interface
- 6.3 SPI Slave Interface
- 6.3.1 Interface
- 6.3.2 Configuration
- 6.3.3 SPI access
- 6.3.4 Commands
- 6.3.5 Address modes
- 6.3.6 Interrupt request register (AL Event register)
- 6.3.7 Write access
- 6.3.8 Read access
- 6.3.9 SPI access errors and SPI status flag
- 6.3.10 EEPROM_LOADED
- 6.3.11 2 Byte and 4 Byte SPI Masters
- 6.3.12 Timing specifications
- 6.4 Asynchronous 8/16 bit µController Interface
- 6.5 Synchronous 8/16 bit µController Interface
- 6.5.1 Interface
- 6.5.2 Configuration
- 6.5.3 µController access
- 6.5.4 µController connection using Byte Select signals (BSn)
- 6.5.5 µController connection using Transfer Size signals (SIZ)
- 6.5.6 Write access
- 6.5.7 Read access
- 6.5.8 µController access errors
- 6.5.9 EEPROM_LOADED
- 6.5.10 Timing Specification
- 7 Distributed Clocks SYNC/LATCH Signals
- 8 SII EEPROM Interface (I²C)
- 9 Example Schematics
- 10 Electrical Specifications and Timings
- 11 Mechanical Specifications
- 12 Appendix
| Recognized languages: | English |
|---|---|
| Pages: | 52 |
| Size: | 1.20 MB |
Show table of contents
Read manual
Document Outline
- Frequently Asked Questions and Troubleshooting
- 1 Introduction
- 2 Frequently unasked questions
- 3 General Issues
- 3.1 Where can I find documentation updates?
- 3.2 ESC clock source accuracy: Is 25 ppm necessary?
- 3.3 Why should port 0 never be an unused port?
- 3.4 Link/Activity LEDs shows strange behavior
- 3.5 Can slaves communicate without SII EEPROM / invalid SII EEPROM content?
- 3.6 Do I need the complete XML ESI description for simple PDI read/write tests?
- 3.7 What do I do with unused ports (EBUS/MII)
- 3.8 Resetting ESC, PHYs, and µController
- 3.9 Should I enable Enhanced Link Detection?
- 3.10 Why must I configure the PHYs for auto-negotiation instead of forcing 100 Mbit+FD?
- 3.11 What is TX Shift and Auto TX Shift?
- 3.12 Frames are lost / communication errors are counted
- 3.13 PDI Performance
- 3.14 Interrupts
- 3.15 Distributed Clocks: Resolution, Precision, Accuracy
- 3.16 Hardware not working
- 4 EtherCAT IP Core for Altera FPGAs
- 4.1 Licensing issues
- 4.2 Implementation issues
- 4.3 Hardware issues
- 4.4 OpenCore Plus design stops operating too early
- 5 EtherCAT IP Core for Xilinx FPGAs
- 6 Appendix