Document Outline

• EC – Declaration of Conformity
• TÜV Certificate
• Product registration
• 1. Safety
  • 1.1 Legal considerations
  • 1.2 Structure of the safety instructions
    • 1.2.1 Signal word panel
    • 1.2.2 Safety alert symbol
    • 1.2.3 Pictograms
    • 1.2.4 Word message panel structure
  • 1.3 Localization / position of safety labels on the unit
  • 1.4 Type plate
  • 1.5 General safety instructions on installing and operating the vacuum drying oven
    • 1.5.1 Safety instructions on installation and ambient conditions
    • 1.5.2 Safety instructions on vacuum supply
    • 1.5.3 Safety instructions on the charging material
    • 1.5.4 Safety instructions on operating the vacuum drying oven
  • 1.6 Intended use
    • 1.6.1 Operation log
• 2. Description of the equipment
  • 2.1 Safety equipment
  • 2.2 Overview of the oven
  • 2.3 VDL control panel
  • 2.4 Connections at the rear of the unit
  • 2.5 “Temperature setting” information panel (ignition temperature vs. drying temperature)
  • 2.6 Overview of the zone classification of the ovens
• 3. Completeness of delivery, transportation, storage, and installation
  • 3.1 Unpacking, and checking equipment and completeness of delivery
  • 3.2 Guidelines for safe lifting and transportation
  • 3.3 Storage
  • 3.4 Location of installation and ambient conditions
• 4. Installation and connections
  • 4.1 Vacuum expansion racks
  • 4.2 Vacuum connection
    • 4.2.1 Notes regarding use of vacuum pumps of other manufacturers
  • 4.3 Inert gas connection
  • 4.4 Compressed air / inert gas connection for sweeping the area for electrical equipment
  • 4.5 Electrical connection
• 5. Start up
  • 5.1 Settings at the RD3 program controller
  • 5.2 General indications
• 6. Fixed value entry mode
• 7. Week program editor
  • 7.1 Program table template for the Week Program Editor
  • 7.2 Programming example of the Week program editor
    • 7.2.1 Desired time function
    • 7.2.2 Proceeding overview
    • 7.2.3 Proceeding in detail
• 8. Program editor
  • 8.1 Selecting between set-point ramp and set-point step
    • 8.1.1 Programming with setting “Ramp” (default setting)
    • 8.1.2 Programming with setting “step”
    • 8.1.3 General notes on programming temperature transitions
  • 8.2 Set-point entry for program operation
  • 8.3 Program table template
  • 8.4 Deleting a program section
• 9. Program start level
• 10. User level
• 11. Performance in case of failures
  • 11.1 Performance after power failures
  • 11.2 Alarm messages
• 12. Safety device class 2 (DIN 12880)
• 13. Reference measurements. Checking the temperature in the inner chamber
• 14. Commissioning the vacuum
  • 14.1 Evacuation
  • 14.2 Breaking the vacuum (flooding with ambient air)
  • 14.3 Operation with inert gas
• 15. Options
  • 15.1 ATEX connection kits for vacuum pumps VP4 or VP5 (option)
  • 15.2 Vacuum module empty (without pump) (option)
  • 15.3 Vacuum module with chemical membrane pump VP4 or VP5 (option)
  • 15.4 Additional measuring channel for digital object temperature display with flexible Pt 100 temperature sensor (option)
  • 15.5 Measuring access port vacuum 9 poles (option)
  • 15.6 Communication software APT-COM™ 3 DataControlSystem (option)
• 16. Maintenance, cleaning, and service
  • 16.1 Maintenance intervals, service
  • 16.2 Cleaning and decontamination
    • 16.2.1 Cleaning
    • 16.2.2 Decontamination
  • 16.3 Sending the unit back to BINDER GmbH
• 17. Disposal
  • 17.1 Disposal of the transport packing
  • 17.2 Decommissioning
  • 17.3 Disposal of the unit in the Federal Republic of Germany
  • 17.4 Disposal of the unit in the member states of the EC except for the Federal Republic of Germany
  • 17.5 Disposal of the unit in non-member states of the EC
• 18. Troubleshooting
• 19. Technical description
  • 19.1 Factory calibration and adjustment
  • 19.2 VDL technical data
  • 19.3 Equipment and Options
  • 19.4 Spare parts
  • 19.5 Dimensions VDL 23
  • 19.6 Dimensions VDL 53
  • 19.7 Dimensions VDL 115
• 20. Contamination clearance certificate
  • 20.1 For units located outside North America and Central America
  • 20.2 For units in North America and Central America
• Word-Lesezeichen
  • OLE_LINK18
  • OLE_LINK19
  • OLE_LINK10
  • OLE_LINK1
  • OLE_LINK4
  • OLE_LINK7
  • OLE_LINK8