BMW K 1100 LT/RS Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for K 1100 LT/RS BMW
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 364 |
| Size: | 8.19 MB |
Show table of contents
Read manual
Document Outline
- Repair Manual
- Introduction
- Maintenance Schedule K 75 RT/K1100RS/LT
- Pre-delivery Check K 75 RT/K1100RS/LT
- Contents
- 00 Maintenance and general instructions
- Tightening torque
- Table of operating fluids
- Key to maintenance intervals
- Changing engine oil
- Changing oil in transmission (gearbox)
- Changing oil in rear wheel drive
- Changing oil in telescopic fork
- Renewing intake air cleaner
- Renewing fuel filter
- Cleaning inductive pulse generator at rear wheel d...
- Checking brake pads, brake discs for wear and rene...
- Checking brake fluid level and correcting if neces...
- Checking brake system
- Checking ABSsensor spacing and adjusting if neces...
- Renewing brake fluid
- Checking function of electric switch on side stand...
- Checking clutch clearance and adjusting if necessa...
- Reading out Motronic defect code memory
- Checking increased starting speed (choke) and adju...
- Checking valve clearance and adjusting if necessar...
- Adjusting valve clearance
- Checking steering bearing play and adjusting if ne...
- Lubricating guide pins, adjustable screen
- Checking idle speed, synchronising and CO value an...
- 11 Motor
- Removing engine
- Dismantling engine
- Removing intermediate flange
- Stripping down and re-assembling intermediate flan...
- Removing countershaft and layshaft with freewheel
- Dismantling and assembling freewheel
- Removing and installing layshaft needle roller bea...
- Removing timing chain cover
- Removing the timing chain
- Removing, stripping down and assembling cylinder h...
- Removing crankshaft
- Removing pistons with conrods, stripping down and ...
- Removing and installing crankshaft pinion and roto...
- Removing, dismantling and assembling combined oil-...
- Removing output shaft
- Stripping and assembling output shaft
- Assembling engine
- Installing output shaft
- Measuring crankshaft bearing play
- Checking dimensions of crankshaft
- Installing crankshaft
- Installing piston with conrod
- Measuring big end bearing play
- Installing big end bearing
- Installing combined oil-water pump
- Installing cylinder head
- Installing camshafts
- Installing timing chain
- Checking valve clearances
- Installing intermediate flange
- Installing driver
- Installing alternator
- Installing timing case cover
- Installing hall-effect transmitter
- Installing cover for Hall-effect transmitter
- Installing cylinder head cover
- Installing engine
- Checking/adjusting valve clearances
- 12 Engine electrics
- 13 Fuel preparation and control
- Adjusting idle speed
- Checking start speed increase (choke), adjusting i...
- Adjusting CO value
- Removing/installing and checking/ adjusting thrott...
- Removing and installing air cleaner insert
- Removing and installing air cleaner housing
- Removing and installing throttle rail
- Removing and installing Motronic control unit
- 16 Fuel tank and lines
- 17 Radiator
- 18 Exhaust system
- 21 Clutch
- 23 Gearbox
- Removing transmission (gearbox)
- Disassembling transmission (gearbox)
- Removing transmission cover.
- Disassembling/assembling transmission cover
- Removing gear selector drum
- Removing gearshift forks
- Removing transmission shafts
- Removing pawl
- Removing selector shaft
- Removing segment
- Removing and installing shaft sealing ring on inpu...
- Removing and installing shaft sealing ring for gea...
- Removing and installing bearing shell for taper ro...
- Removing and installing ball bearing on intermedia...
- Disassembling and assembling input shaft
- Disassembling and assembling output shaft
- Installing transmission shafts
- Installing gearshift forks
- Measuring distances between transmission shafts
- Installing transmission cover
- Installing transmission (gearbox)
- 31 Front fork
- Removing telescopic fork
- Disassembling telescopic fork
- Assembling telescopic fork
- Installing telescopic fork
- 32 Steering
- 33 Rear wheel drive
- Removing, disassembling, assembling and installing...
- Removing rear wheel drive
- Removing, disassembling and assembling drive bevel...
- Installing drive bevel gear
- Removing and installing taper needle bearing in re...
- Removing crown wheel
- Installing crown wheel
- Checking/adjusting tooth backlash
- Checking contact pattern
- Shimming housing cover
- Installing housing cover
- Installing slider
- Installing rear wheel drive
- Removing, disassembling and assembling rear swingi...
- Removing, disassembling, assembling and installing...
- 34 Brakes
- Removing and installing front brake caliper
- Dismantling and assembling front brake caliper
- Removing and installing front brake disc
- Removing and installing front ABS sensor
- Adjusting front ABS sensor gap
- Removing and installing front brake line
- Removing and installing ABS brake line from front ...
- Removing and installing handbrake cylinder
- Bleeding brake
- Removing and installing pressure modulator
- [ABS II] Removing and installing relay and relay b...
- Removing and installing rear brake caliper
- Removing and installing rear brake pads
- Dismantling and assembling rear brake caliper
- Removing and installing rear brake disc
- Removing and installing rear ABS sensor
- Measuring vertical runout at rear pulse wheel
- Removing and installing rear master brake cylinder...
- Removing and installing brake pedal
- Adjusting foot brake pedal
- Troubleshooting: Front wheel/rear wheel brake
- 36 Wheels and tyres
- 46 Frame
- Removing and installing front mudguard
- Removing and installing rear section
- Removing and installing rear mudguard
- Removing and installing fairing [LT]
- Removing and installing fairing [RS]
- Checking running gear
- Removing and installing frame
- Removing and installing main centre stand
- Checking switching function of side stand
- 51 Equipment
- 61 General electrical equipment
- 62 Instruments
- Removing and installing instrument cluster
- [LT]
- [RS]
- Disassembling and assembling instrument cluster
- Removing and installing indicator lamp
- Removing and installing p.c. board
- Removing and installing quartz clock
- Removing and installing frame for indicator lamps
- Removing and installing p.c. board for fuel gauge
- Removing and installing revolution counter
- Removing and installing speedometer
- Removing and installing p.c. board for gear indica...
- Removing and installing instrument cluster
- 63 Lights