Document Outline

• 645 User's manual
• Table of Contents
  • 1. General Information
    • 1.1 Feature Overview
    • 1.2 Warranty Information
    • 1.3 Precaution of Operation
    • 1.4 Upkeep of Model 645
    • 1.5 Safety Information
    • 1.6 Symbols and Terms
    • 1.7 Inspection
    • 1.8 Options and Accessories
  • 2. Overview
    • 2.1 To adjust the handle
    • 2.2 Factory Default settingd
    • 2.3 Model 645 Operation panels
      • 2.3.1 Front panel
  • 3. Common Operations
    • 3.1 Graph Mode
    • 3.2 Numerical/Alphabetical Entry
    • 3.3 To select Output Function
    • 3.4 To set Output Frequency/Period
    • 3.5 To set output Amplitude
    • 3.6 To set DC Offset Voltage
    • 3.7 To set High-Level and Low-Level Bounds
    • 3.8 To set Waveform Polarity
    • 3.9 To set Output Termination
    • 3.10 To Enable/Disable Voltage Autoranging
    • 3.11 To Control Output connector
    • 3.12 To Enabled/Disable Sync Out Signal
    • 3.13 To Restore the Factory Default settings
  • 4. Waveform output Operations
    • 4.1 Sine Wave
    • 4.2 Square Wave
    • 4.3 Ramp Wave
    • 4.4 Noise Waveform
    • 4.5 Pulse Waveform
    • 4.6 Arbitrary Waveform
    • 4.7 Amplitude Modulation
    • 4.8 Frequency Modulation
    • 4.9 Phase Modulation
    • 4.10 FSK Modulation
    • 4.11 PWM Waveform
    • 4.12 Frequency Sweep
    • 4.13 Burst Operation
    • 4.14 Pattern Output
  • 5. System Operations
    • 5.1 Triggering
    • 5.2 Storing the instrument state
    • 5.3 Display Control
    • 5.4 Beeper
    • 5.5 Sound
    • 5.6 Error Display
    • 5.7 Calibration
  • 6. Remote Interface Operations
    • 6.1 Remote Interface Configuration
      • 6.1.1 USB Interface
      • 6.1.2 GPIB Interface
      • 6.1.3 LAN Interface
    • 6.2 Remote Interface commands
  • 7. Error Messages
    • 7.1 Command Errors
    • 7.2 Execution Errors
    • 7.3 Device Dependent Errors
    • 7.4 Query Errors
    • 7.5 Instriment Errors
    • 7.6 Self-Test Errors
    • 7.7 Calibration Errors
    • 7.8 Arbitrary Waveform Errors
  • Appendix
    • A. Specification List
    • B. Remote Interface Reference
      • B.1 An Introduction to the SCPI Language
        • B.1.1 Command Format Used in this Manual
        • B.1.2 Command Separators
        • B.1.3 Using the MIN and MAX parameters
        • B.1.4 Querying parameter settings
        • B.1.5 SCPI command Terminators
        • B.1.6 IEEE-488.2 Common commands
        • B.1.7 SCPI Parameter Types
      • B.2 Output Data Formats
      • B.3 Command Reference
        • A to F
          • A
          • B
          • C
          • D
          • F
        • I to O
          • I
          • L
          • M
          • O
        • P to Z
          • P
          • R
          • S
          • T
          • U
          • V
          • W
      • B.4 SCPI Compliance Information
      • B.5 IEEE-488 Compliance Information
      • B.6 Using Device clear to Halt Measurements
    • C. General Specifications
    • D. Application Programs