Document Outline

• BOXLIGHT XD-15c
• Copyright
• Disclaimer
  • Fill this in!!
  • Introduction 1
  • Installation 11
  • Operation 12
  • Maintenance 20
  • Troubleshooting 24
  • Specifications 26
  • Dimensions 28
• Introduction
  • 1. Read this user’s guide before you operate your projector and save it for future reference.
  • 2. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately...
  • 3. Never replace lamp assembly or any electronic components unless the projector is unplugged.
  • 4. To reduce the risk of electric shock, do not disassemble this appliance. Take it to a qualifie...
  • 5. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaini...
  • 6. This product is capable of displaying inverted images for ceiling mount installation. Please u...
  • WARRANTY LIMITATION AND EXCLUSION
  • DISCLAIMER OF UNSTATED WARRANTIES
  • LIMITATION OF LIABILITY
    • 1. Mac adapter (switchable)
    • 2. Spare lamp module
      • 1. External control panel (see next page)
    • 2. Projection lens
    • 3. Front adjustment feet
    • 4. IR remote sensor
    • 5. Ventilation grill
    • 6. Kensington lock
    • 7. AC power cord input
    • 8. S-video connector
    • 9. Video connector
    • 10. D-sub connector (for computer/ HDTV input)
    • 11. Audio input
    • 12. Rear adjustment feet
    • 13. Lamp access door (underneath unit)
      • 1. Lift the projector up and press the adjuster button to release the adjuster.
    • 2. The adjuster will drop into position and be locked.
  • FREEZE
• Installation
• Operation
  • 1. Plug the power cord into a wall socket.
  • 2. Press POWER for 1 second.
  • 3. Switch on all connected equipment.
    • 1. Default
  • 2. Ceiling - mounted projection
  • 3. Rear screen projection
  • 4. Ceiling - mounted and rear screen projection
    • 1. Press POWER and a warning message will prompt up. To turn off the projector, Press POWER again.
  • 2. The fan will continue to run for approximately 60 seconds.
  • 3. Disconnect the power cord from the wall socket.
• Maintenance
  • 1. Press the POWER button to switch off the projector. Disconnect the power cord from the outlet ...
  • 2. Loosen the screw and remove the lamp cover. If the lamp is hot, avoid burns by waiting 45 minu...
  • 3. Loosen the 3 screws. (It is strongly recommended you use a magnetic-headed screwdriver.) Pull ...
  • 4. Replace the lamp with a new one. Insert it into the projector, and tighten the screws firmly. ...
  • 5. Re-install the lamp cover and tighten the screw. Do not turn on the power with the lamp cover ...
  • OSD
  • FUNCTION
• Troubleshooting
• Specifications
  • Technical Specifications
  • Resolution
  • H Sync (kHz)
  • V Sync (Hz)
  • Remark
    • 640x350
    • 31.5
    • 70.1
    • 640x400
    • 37.9
    • 85.1
    • VESA
    • 720x400
    • 31.5
    • 70.0
    • 720x400
    • 37.9
    • 85.1
    • VESA
    • 640x480
    • 31.5
    • 60.0
    • VESA
    • 640x480
    • 37.9
    • 72.8
    • VESA
    • 640x480
    • 35.0
    • 66.7
    • Macintosh
    • 640x480
    • 43.3
    • 85.0
    • VESA
    • 800x600
    • 35.2
    • 56.3
    • VESA
    • 800x600
    • 37.9
    • 60.3
    • VESA
    • 800x600
    • 46.9
    • 75.0
    • VESA
    • 800x600
    • 48.1
    • 72.2
    • VESA
    • 800x600
    • 53.7
    • 85.1
    • VESA
    • 832x624
    • 49.7
    • 74.5
    • Macintosh
    • 1024x768
    • 48.4
    • 60.0
    • VESA
    • 1024x768
    • 56.5
    • 70.1
    • VESA
    • 1024x768
    • 60.0
    • 75.0
    • VESA
    • 1024x768
    • 68.7
    • 85.0
    • VESA
    • 1280x1024
    • 64.0
    • 60.0
    • VESA
• Dimensions