Document Outline

• FCC Declaration of Conformity
  • Compliance Information
• CE Declaration of Conformity
• Contents
• About This Document
  • Who Should Use This Document
  • How This Document Is Organized
  • Contacts
    • Unitied States
    • European Union (EU)
    • Asia Pacific
  • Document Conventions
• Introduction
  • External View
  • Printer Components
  • Control Panel
    • Control Panel LCD
    • Control Panel Buttons
    • Control Panel Indicator Lights
• Printer Setup
  • Before You Begin
  • Handling the Printer
    • Unpack and Inspect the Printer
    • Store the Printer
    • Ship the Printer
    • Recycle the Printer
  • Select a Site for the Printer
    • Select a Surface
    • Provide Proper Operating Conditions
    • Allow Proper Space
    • Provide a Data Source
    • Provide a Power Source
  • Select a Communication Interface
    • Connector Locations
    • Types of Connections
    • Data Cable Requirements
  • Connect the Printer to a Power Source
    • Power Cord Specifications
  • Types of Media
  • Ribbon Overview
    • When to Use Ribbon
    • Coated Side of Ribbon
• Operations
  • Prepare the Media for Loading
  • Print Modes
  • Load Media in Tear-Off Mode
  • Load Ribbon
    • Remove Used Ribbon
  • Calibrate the Printer
  • Adjust Media Sensors
    • Upper Media Sensor-Inside Half of Media
    • Upper Media Sensor-Outside Half of Media
    • Lower Media Sensor
  • Adjust Printhead Pressure and Toggle Position
    • Toggle Position Adjustment
    • Printhead Pressure Adjustment
• Configuration
  • Setup Mode
    • Enter Setup Mode
    • Exit Setup Mode
  • Change Password-Protected Parameters
    • Default Password Value
    • Disable the Password Protection Feature
  • Print a Configuration Label
  • Print a Network Configuration Label
  • Control Panel Parameters
    • How to View or Modify Parameters
    • Additional Parameters
    • Standard Printer Parameters
• Print Modes
  • Print Modes
    • Select the Print Mode
    • Tear-Off Mode
    • Load Media in Peel-Off Mode
    • Load Media in Cutter Mode
    • Load Media in Rewind Mode (No Cutter)
    • Load Media in Rewind Mode with Cutter Option
    • Install the Rewind Plate
    • Remove Media Liner from the Rewind or Peel Spindle
• Routine Maintenance
  • Cleaning Schedule
  • Clean the Exterior
  • Clean the Media Compartment
  • Clean the Printhead and Platen Roller
  • Clean the Sensors
    • Ribbon and Label-Available Sensor Locations
    • Transmissive (Media) Sensor Locations
  • Clean the Snap Plate
  • Clean the Cutter
  • Replace the Fuse (360X-Plus II Only)
• Troubleshooting
  • Troubleshooting Checklists
  • LCD Error Messages
  • Print Quality Problems
  • Calibration Problems
  • Communications Problems
  • Ribbon Problems
  • Miscellaneous Printer Problems
  • Printer Diagnostics
    • Power-On Self Test
    • CANCEL Self Test
    • PAUSE Self Test
    • FEED Self Test
    • FEED and PAUSE Self Test
    • Communications Diagnostics Test
    • Sensor Profile
• Data Ports
  • Parallel Data Port
    • Parallel Cabling Requirements
    • Parallel Port Interconnections
  • Serial Data Port
    • Hardware Control Signal Descriptions
    • Pin Configuration
    • RS-232 Interface Connections
  • Applicator Interface Connector
    • Applicator Signals
    • Applicator Interface Connector Pin Configuration
    • Jumper Configurations and Pinouts for +5 V I/O Operation
    • Pinouts for +24-28 V I/O Operation
• Specifications
  • Features
    • Standard Features
    • Print Modes
    • Zebra Programming Language (ZPL)
    • Bar Codes
  • Agency Approvals
  • General Specifications
    • Physical Specifications
    • Electrical Specifications
    • Environmental Conditions for Operation and Storage
  • Print Specifications by Model
  • Ribbon Specifications
  • Media Specifications
    • BP-300X-Plus II and 600 X-Plus II Printers
    • BP-360X-Plus II Printers
• Glossary
• Index