Document Outline

• Title Page
• Notice
• Contents
• Introduction
  • 1.1 General
  • 1.2 Organization of This Document
  • 1.3 Document Conventions
  • 1.4 Getting Help
  • 1.5 CSMIM-T1 Overview
    • 1.5.1 Software Information
  • 1.6 CSMIM-T1 Front Panel
    • 1.6.1 Console Port
    • 1.6.2 System LED Indicators
    • 1.6.3 The SET UP Switch
    • 1.6.4 T-1 Network Access
    • 1.6.5 NETWORK STATUS / ALARMS
    • 1.6.6 Modem Configuration Status LEDs
    • 1.6.7 Modem Port Status LEDs
    • 1.6.8 EFS Key Number
  • 1.7 Connectivity
  • 1.8 Telco Connection Information
    • 1.8.1 Connecting the CSMIM-T1 to a Full T-1 Line
    • 1.8.2 Connecting the CSMIM-T1 to a Fractional T-1 ...
  • 1.9 Compatibility
  • 1.10 CSMIM-T1 Physical / Statistical 1.10 Informat...
• Installing the CSMIM-T1
  • 2.1 General
  • 2.2 Locating the Ethernet Jumpers
    • 2.2.1 Setting the Ethernet Jumpers
    • 2.2.2 Setting the Subnet Jumper
  • 2.3 Network Bypass Jumper
  • 2.4 Installing the CSMIM-T1
  • 2.5 Making Connections
    • 2.5.1 Connecting a Console Terminal
    • 2.5.2 Connecting a T1 Network Interface
    • 2.5.3 Connecting a Drop/Insert Interface
  • 2.6 Power-up and Test
  • 2.7 Auto-initializing the ROMs
    • 2.7.1 BOOTP
    • 2.7.2 RARP
  • 2.8 Software Installation Procedures
    • 2.8.1 Invoking the Console Monitor
    • 2.8.2 Self-Booting the CSMIM-T1
    • 2.8.3 Reloading EFS Key Value
• ROM Monitor Commands
  • 3.1 General
  • 3.2 Commands
    • 3.2.1 addr
    • 3.2.2 boot
    • 3.2.3 config
    • 3.2.4 console-baud
    • 3.2.5 erase
    • 3.2.6 help
    • 3.2.7 image
    • 3.2.8 ipx
    • 3.2.9 lat_key
    • 3.2.10 mop
    • 3.2.11 net
    • 3.2.12 option_key
    • 3.2.13 ping
    • 3.2.14 ports
    • 3.2.15 sequence
    • 3.2.16 slip
    • 3.2.17 stats
• CSMIM-T1 Parameters
  • 4.1 General
  • 4.2 T-1 Commands
  • 4.3 T-1 Parameters
  • 4.4 Parameter Descriptions
  • 4.5 Set T-1 Parameters Example
• Troubleshooting Procedures
  • 5.1 General
  • 5.2 Power-Up and Boot Procedures
    • 5.2.1 Normal Mode CSMIM-T1 Diagnostics
    • 5.2.2 SET UP Mode
  • 5.3 BOOT Failures
    • 5.3.1 Boot Error Report
    • 5.3.2 Correcting CSMIM-T1 Parameters
  • 5.4 CSMIM-T1 Dumps
• Modem Guide
  • 6.1 General
  • 6.2 Features
  • 6.3 Using the AT Command Set
    • 6.3.1 Key AT Command Factory Defaults
    • 6.3.2 Establishing 11-Bit Data Connections
    • 6.3.3 V.32bis Cellular Connections Using AT 6.3.3 ...
  • 6.4 Modulation Protocols
    • 6.4.1 Protocol Configuration Command Settings
    • 6.4.2 Speed and Protocol Connection Matrices
  • 6.5 Error Correction
  • 6.6 Diagnostics
    • 6.6.1 Power-Up Diagnostics
    • 6.6.2 Local Analog Loopback with Self-Test
    • 6.6.3 Local Analog Loopback
    • 6.6.4 Remote Digital Loopback with Self-Test
    • 6.6.5 Remote Digital Loopback
    • 6.6.6 Local Digital Loopback
    • 6.6.7 Respond to Remote Digital Loopback
    • 6.6.8 Automatically Terminating a Test: Register S...
  • 6.7 Result Codes
    • 6.7.1 Connection Result Code Tables
• AT Commands and Registers
  • 7.1 The Command Set
    • 7.1.1 Entering Commands
  • 7.2 Commands
    • 7.2.1 Operating Mode Dial Modifiers
  • 7.3 Registers
    • 7.3.1 Commands to Change or Read Registers
• Port Pin/Signal Allocations
  • A.1 General
  • A.2 Console Port
  • A.3 Interface Ports
  • A.4 Additional Enterasys Cables and A.4 Connectors...
• Index