Document Outline

• Title Page
• Notice
• Contents
• Preface
  • Technical Support
  • Typographical Styles
  • Important Information Indicators
  • Laser Warning
  • Safety Agency Compliance
    • Safety Precautions
    • Symbols
    • Modifications to Equipment
    • Placement of a Enterasys Systems Product
    • Power Cord Connection
• Introduction
  • 1.1 Overview of the ATM Standard
  • 1.2 Hardware Description
    • 1.2.1 Front Panel Description
    • 1.2.2 9A000 and SFCS Series Hardware Configuration...
    • 1.2.3 9A000 and SFCS Series Switch Board
    • 1.2.4 Switch Control Processor
    • 1.2.5 9A000 and SFCS Series Network Modules
    • 1.2.6 Environmental Information
    • 1.2.7 Standards Compliance
    • 1.2.8 Safety Compliance
    • 1.2.9 Emissions Compliance
    • 1.2.10 Electromagnetic Compatibility (EMC)
  • 1.3 Software Description
    • 1.3.1 Switch Control Software
• Installing the 9A000
  • 2.1 Installing the 9A000
  • 2.2 The Reset Switch
• Switch Hardware
  • 3.1 Switch Hardware Configurations
  • 3.2 Switch Hardware Components
    • 3.2.1 Switch Board
    • 3.2.2 Switch Control Processor
      • 3.2.2.1 i960 Switch Control Processor
    • 3.2.3 Network Modules
      • 3.2.3.1 Port Numbering
    • 3.2.4 Power Supply Modules
      • 3.2.4.1 SFCS-200BX AC Power Supply
      • 3.2.4.2 SFCS-1000 AC Power Supply (Model A)
      • 3.2.4.3 SFCS-1000 AC Power Supply (Model B)
    • 3.2.5 SFCS-1000 Fan Tray
    • 3.2.6 SFCS-1000 Temperature Sensing
    • 3.2.7 SFCS-1000 Common Equipment Card (CEC)
      • 3.2.7.1 CEC Front Panel
      • 3.2.7.2 Alarm Relay Contacts
      • 3.2.7.3 CEC Status LEDs
      • 3.2.7.4 Ethernet Port
• Switch Setup
  • 4.1 Introduction
  • 4.2 Unpacking
    • 4.2.1 Inventorying the Unit
  • 4.3 Electrical Considerations
  • 4.4 Rack-Mounting an SFCS-200BX
    • 4.4.1 Required Tools
    • 4.4.2 Installing the Rack-mount Brackets
  • 4.5 Rack-Mounting an SFCS-200WG
    • 4.5.1 Required Tools
    • 4.5.2 Installing the Rack-mount Brackets
  • 4.6 Rack-Mounting an SFCS-1000
    • 4.6.1 Installing the SFCS-1000
  • 4.7 Installing the Serial Cable
  • 4.8 Modem Configuration
    • 4.8.1 Modem Parameters
  • 4.9 Configuring IP Addresses
  • 4.10 AMI Security
  • 4.11 Subsequent Operation
  • 4.12 Verifying the Installation
  • 4.13 Product Registration Information
• Hardware Maintenance Procedures
  • 5.1 Network Module Replacement
  • 5.1.1 Overview
  • 5.1.2 Multicast Mode
  • 5.1.3 Hot-swapping Network Modules
  • 5.2 Power Supply Module Replacement
    • 5.2.1 SFCS-200BX Power Supply Module Replacement
      • 5.2.1.1 Replacing an SFCS-200BX AC Power Supply
    • 5.2.2 SFCS-1000 Power Supply Module Replacement
      • 5.2.2.1 Replacing an SFCS-1000 AC Power Supply (Mo...
      • 5.2.2.2 Replacing an SFCS-1000 AC Power Supply (Mo...
  • 5.3 SFCS-1000 Fan Tray Replacement
  • 5.4 Switch Control Processor Replacement
  • 5.5 Switch Board Replacement
• Software Upgrade Instructions
  • 6.1 Obtaining the Software Upgrade File via Disket...
  • 6.2 Performing the Software Upgrade
  • 6.3 Changing between Multiple Versions of Software...
  • 6.4 Using bootp to Download Software to the Switch...
    • 6.4.1 Overview
    • 6.4.2 Setting Up Your bootp Server
    • 6.4.3 Adding an Entry for Your Switch in the bootp...
    • 6.4.4 Setting Up a tftpboot Server
• Appendix A
  • A.1 Adapter Hardware Troubleshooting
    • A.1.1 Run Looptest
    • A.1.2 Check Self-Test (Automatically Performed)
    • A.1.3 Firmware Download (Automatically Performed)
    • A.1.4 Hardware Detected by Driver
    • A.1.5 Check Firmware
    • A.1.6 Check Physical Link
  • A.2 Testing Network Connectivity Using PVCs
    • A.2.1 Verifying the Outgoing ATM ARP Entry
    • A.2.2 atmstat
      • A.2.2.1 No Cells Received by Remote End
      • A.2.2.2 Cells and VPI/VCI Errors Received by Remot...
      • A.2.2.3 Cells and AAL* Errors Received by Remote
      • A.2.2.4 Cells and No Errors Received by Remote and...
      • A.2.2.5 Cells and No Errors Received by Remote and...
  • A.3 Collecting Additional Information
    • A.3.1 Basic Information
    • A.3.2 Adapter Information
    • A.3.3 Switch Information
• Appendix B
  • B.1 SFCS-200WG, SFCS-200BX, SFCS-1000 Diagnostics
    • B.1.1 Accessing the Monitor Mode
    • B.1.2 Running the Hardware Tests
      • B.1.2.1 Clock Test
      • B.1.2.2 DRAM Test
      • B.1.2.3 DRAM Chip Test
      • B.1.2.4 Ethernet Test
      • B.1.2.5 FLASH Test
      • B.1.2.6 FLASH Chip Test
      • B.1.2.7 Serial Port Test
      • B.1.2.8 SRAM Test
      • B.1.2.9 Timer Test
      • B.1.2.10 Hardware Test
      • B.1.2.11 Complete Hardware Test
• Appendix C
  • C.1 Enterasys ATM Switches
    • C.1.1 SFCS-200WG
    • C.1.2 SFCS-200BX
    • C.1.3 SFCS-1000
  • C.2 ATM Network Modules
    • C.2.1 100 Mbps TAXI Module
    • C.2.2 155 Mbps OC-3c/STM-1 MM Module
    • C.2.3 155 Mbps STS-3c/STM-1 UTP Module
      • C.2.3.1 155 Mbps UTP Pinout Specifications
      • C.2.3.2 Connecting Switches with 155 Mbps UTP Netw...
    • C.2.4 622 Mbps OC-12c/STM-4c MM Module
    • C.2.5 25 Mbps TP25 Module
      • C.2.5.1 Connecting Switches with TP25 Network Modu...
      • C.2.5.2 Connecting Switches with Token Ring Pinout...
      • C.2.5.3 Connecting Adapters with Token Ring Pinout...
    • C.2.6 34 Mbps E3 Module
    • C.2.7 45 Mbps DS3 Module
    • C.2.8 155 Mbps OC-3c/STM-1 SM Module
    • C.2.9 155 Mbps OC-3c/STM-1 3MM/1SM Module
    • C.2.10 622 Mbps OC-12c/STM-4c SM Module
  • C.3 ATM Adapters
    • C.3.1 Adapter Cabling Specifications
      • C.3.1.1 Fiber-Optic Cable Specifications
      • C.3.1.2 UTP Cable Specifications
      • C.3.1.3 UTP Pinouts
    • C.3.2 ESA-200PC Technical Specifications
    • C.3.3 PCA-200PC Technical Specifications
    • C.3.4 PCA-200MAC Technical Specifications
    • C.3.5 NBA-200 Technical Specifications
    • C.3.6 GIA-200 Technical Specifications
    • C.3.7 HPA-200 Technical Specifications
    • C.3.8 MCA-200 Technical Specifications
    • C.3.9 SBA-200 Technical Specifications
    • C.3.10 ESA-200 Technical Specifications
    • C.3.11 VMA-200 Technical Specifications
• Glossary