Document Outline

• Table of Contents
• Table of Figures
• Chapter 1 - Introduction
  • 1.0 Purpose
  • 1.1 New Features
    • 1.1.1 SFP SM/MM Designation in UI
    • 1.1.2 SFP Power Detection
    • 1.1.3 RMTF Transmitted TRAP and Syslog Message
    • 1.1.4 Aux IP Rate Limiting
    • 1.1.5 PCP/DSCP Verification Mechanism
    • 1.1.6 Line Rate Utilization Field in UI
    • 1.1.7 Prevent Configuration Change During Latency/Jitter Test
    • 1.1.8 PM Manual Test Indication
    • 1.1.9 Extension Port VLAN Filtering
    • 1.1.10 Addition of New MIBs for CV2.0
    • 1.1.11 Expand VLAN Translation Table to 128 Entries
    • 1.1.12 LLC Encapsulation Option for CFM
    • 1.1.13 Firmware Upgrade on Next Reset
    • 1.1.14 Remove Configuration File Feature
    • 1.1.15 MOCANA Update
    • 1.1.16 Filtering of Tagged UDLD Frames
    • 1.1.17 Stagger SNTP Requests
    • 1.1.18 PM/SAM License Policy
    • 1.1.19 Service Availability Monitor (SAM)
    • 1.1.20 IEEE 802.1ag VLAN Loopback
    • 1.1.21 UTP Cable Diagnostics
    • 1.1.22 IFX MIB
    • 1.1.23 Port Based VLAN Control (PBVC)
    • 1.1.24 Broadcast Ping
    • 1.1.25 Autonegotiation Speed Selection
  • 1.2 Management Security
  • 1.3 Optional Features
• Chapter 2 - Getting Started
  • 2.0 Factory Configuration Settings
  • 2.1 Setting Up VT-100 Terminal Management
  • 2.2 Setting Up SNMP Network Management
    • 2.2.1 Network Management Platform Set-up
    • 2.2.2 9145 Set-up
  • 2.3 Management User Interface
    • 2.3.1 General Screen Format
  • 2.4 Login
  • 2.5 Main Menu
• Chapter 3 - System Configuration
  • 3.0 System Configuration Menu
  • 3.1 IP/SNMP Agent Configuration
    • 3.1.1 IP Addresses
    • 3.1.2 Management IP Configuration
      • 3.1.2.1 Management IP Setup
      • 3.1.2.2 Test IP Setup
      • 3.1.3 Auxiliary IP Configuration
      • 3.1.4 Host Table
      • 3.1.5 Trap/Notification Destination Table
  • 3.2 Trap Configuration
  • 3.3 Security Configuration
  • 3.4 Account Configuration
    • 3.4.1 Add an Account
    • 3.4.2 Edit an Account
    • 3.4.3 Delete an Account
  • 3.5 System Information
  • 3.6 RADIUS Client Configuration
  • 3.7 SNTP Client Configuration
  • 3.8 SYSLOG Client Configuration
  • 3.9 Hardware Information
• Chapter 4 - Diagnostics
  • 4.0 Diagnostics Functions
  • 4.1 Loopback Setup
  • 4.2 Latency/Jitter Test
  • 4.3 PING Generation
  • 4.4 VLAN Loopback
    • 4.4.1 802.1AG Loopback Configuration
    • 4.4.2 VLAN Loopback Statistics
    • 4.4.3 L2 Ping Generator
  • 4.5 Cable Diagnostics
• Chapter 5 - Port Information
  • 5.0 User and Extension Port Description
  • 5.1 Link Status
  • 5.2 Port Configuration
    • 5.2.1 Hardware Information
    • 5.2.2 Functional Configuration
    • 5.2.3 VLAN Configuration
      • 5.2.3.1 VLAN Rules
      • 5.2.3.2 User Port VLAN ID Translation Table
      • 5.2.3.3 Extension Port VLAN ID Translation Table
      • 5.2.3.4 P-Bit Translation Table
    • 5.2.4 Port Filters
  • 5.3 Layer 2 Statistics
  • 5.4 RMON Group 1 Statistics
• Chapter 6 - System Alarms & Logs
  • 6.0 System Alarms
  • 6.1 System Log
    • 6.1.1 Log Display Filter Configuration
• Chapter 7 - Utilities
  • 7.0 Utilities Menu
  • 7.1 Set Date and Time
  • 7.2 Reset Configuration To Default
  • 7.3 Change Password
  • 7.4 VT100 Baud Rate
  • 7.5 Slip/PPP Baud Rate
  • 7.6 PING Generation
  • 7.7 Static ARP Table
  • 7.8 Dynamic ARP Table
• Chapter 8 - Software Upgrade
  • 8.0 Flash Memory
  • 8.1 Software Reset
  • 8.2 Swap Bank & Reset
  • 8.3 Swap Bank After Download and Reset
  • 8.4 Get New File with TFTP
• Chapter 9 - 802.3AH OAM
  • 9.0 Operation, Administration and Maintenance Sublayer
  • 9.1 OAM Control
    • 9.1.1 OAM Admin State
    • 9.1.2 OAM Mode
    • 9.1.3 OAM Loopback Command
    • 9.1.4 Process Rx Loopback OAMPDU
    • 9.1.5 Process Rx Link Fault Flag
    • 9.1.6 Fwd Critical Event
  • 9.2 OAM Statistics
  • 9.3 OAM Event Configuration
  • 9.4 OAM Event Log
    • 9.4.1 Event Log Detail Display
    • 9.4.2 Display Filter Configuration