Document Outline

• INSTALLATION
• AND
• SERVICE
• INFORMATION
• Carrier
• CONTENTS
• 26H
  • CARRIER
  • AUTOMATIC ICEMAKER
  • An automatic, low-cost ICE PLANT .
  • right in your PLACE of BUSINESS!
• 26H3
  • SPECIFICATIONS
    • Carrier
      • An automatic, low-cost ICE PLANT . . . right in your PLACE of BUSINESS!
• 26H5
  • SPECIFICATIONS
    • Carrier
• À 1
  • 1. CHECK SHIPMENT
  • STORAGE BIN CRATE
  • HEAT INTERCHANGER PACKAGE
  • STORAGE BIN PARTITION
  • 2. SELECT PROPER LOCATION
  • 3. MOVE UNIT TO LOCATION
  • 26H
    • INSTALLATION
      • Carrier
        • 4. UNCRATE THE BIN
        • 5. INSTALL LEVELING SCREWS
        • 6. UNPACK AND MOUNT THE HEAT INTERCHANGER
        • 7. MOVE THE BIN TO APPROXIMATE LOCATION
        • 8. UNCRATE THE MACHINE SECTION
        • 9. REMOVE THE FRONT TOP, AND SIDE PANELS
        • 10. PLACE MACHINE SECTION ON TOP OF BIN AND BOLT IN POSITION
        • n. BOLT TIE BAR AT REAR OF UNIT
        • 12. INSTALL WATER SUPPLY AND DRAINS
        • FIG. 8 - PARTS SHIPPED ON BACK OF MACHINE SECTION
        • 13. MAKE ELECTRICAL CONNECTIONS
        • -INPUT-
        • -OUTPUT-
        • FIG. n - "BUCK AMD BOOST" TRANSFORMER WIRING
  • 26H
    • INSTALLATION
      • Carrier
        • 14. INSTALL BIN THERMOSTAT BULB
        • RIGHT SIDE OF 26H3 SECTION - PANELS REMOVED
        • 15. INSTALL CRUSHER GUARD
        • 16. INSTALL SIPHON STANDPIPE AND ADJUST FLOAT
        • FLOAT ASSEMBLY
        • 17. REPLACE THE ICE DEFLECTOR
        • 18. LOOSEN COMPRESSOR HOLD-DOWN BOLTS
        • 19. START THE UNIT
        • 20. CHECK OPERATION
        • 21. FINAL CHECK LIST
        • FREEZING CYCLE (SEE FIG. 1)
        • DEFROST CYCLE (SEE FIG. 2)
        • FIG. 1 - SCHEMATIC FREEZING CYCLE
        • CRUSHER OPERATION
        • 2. REFRIGERANT CIRCUIT
          • L SHUTOFF VALVES
          • 2. INSTALLING GAUGES
          • FIG. 11 - CHARGING MANIFOLD ATTACHED FOR CHARGING UNIT
          • 3. PUMP DOWN OF COMPRESSOR
          • 4. CHARGING WITH REFRIGERANT
          • 5. OPERATING PRESSURES
          • 6. COMPRESSOR
          • 7. LIQUID-SUCTION INTERCHANGER AND ACCUMULATOR REPLACEMENT
          • 8. DRYER REPLACEMENT
          • 9. CONDENSER CLEANING AND REPLACEMENT
          • FIG. 15 - REQUIRED FOR CONDENSER CLEANING
          • 10. EVAPORATOR REPLACEMENT
        • 3. FREEZING WATER CIRCUIT
          • n. FLOAT VALVE
          • 12. WATER DISTRIBUTOR
          • 13. WATER REGULATING VALVE ADJUSTMENT
          • 14. WATER TREATMENT
          • 15. WATER SYSTEM CLEANING
          • 16. WATER PUMP LUBRICATION
          • 17. TESTING AND REPLACING THE WATER PUMP
          • 18. VARIATION OF CUBES
          • 19. CRUSHER
          • fig. 22 - CRUSHER GUARD ASSEMBLY
        • 4. ELECTRICAL CIRCUIT
          • 20. CHECKING VOLTAGE
          • 21. LOOSE TERMINALS
          • 22. SELECTOR SWITCH
          • 23. CONTROL BOX
          • 24. CAPACITORS
          • 25. RELAY
          • 26. COMPRESSOR MOTOR OVERLOAD
          • 27. CRUSHER ELECTRIC CIRCUIT
          • 28. CONTROLS
          • 29. SAFETY OVERFLOW
          • 31. HIGH PRESSURE SWITCH
          • FRONT
          • 240, 160 a 100 LB. BINS
          • 32. TESTING THE SOLENOID VALVE
        • ICE MAKER SERVICE CHECK LIST
        • SERVICE ANALYSIS 26H5 AND 26H3 UNIT WILL NOT OPERATE
          • ERRATIC OPERATION
    • SERVICE
  • 26H
    • Carrier
    • SERVICE PARTS
  • 26H