Document Outline

• © Copyright 2007 Compex Systems Pte Ltd
• Trademark Information
• Disclaimer
• FCC NOTICE
• Declaration of Conformity
• Firmware
• This manual is written based on Firmware version 2
• Table of Contents
• Overview the Product
  • Introduction
  • Features and Benefits
•  Compact Form Factor
•  Multiple-SSID Supporting VLAN Segmentation.
•  Long Range Support
•  Bandwidth Control
•  Wireless Distribution System (WDS2)
•  Parallel Broadband
•  Antenna Control and Alignment
•  DHCP Relay
•  Remote Firmware Upgrade
•  RIP 1 / 2
  • When to Use Which Mode
    • Access Point Mode
    • Access Point Client Mode
    • Wireless Routing Client Mode
    • Gateway Mode
    • Wireless Adapter Mode
    • Transparent Client Mode
    • Repeater Mode
• Panel Views and Description
• Install the Hardware
  • Setup Requirements
    • Using power adapter to supply power to the unit
    • Using PoE to supply power to the unit
  • Setup for Windows XP/2000
• Access the Web Interface
  • Access with uConfig
  • Manual access with Internet Explorer
• Perform Basic Configuration
  • Setup Management Port
    • Setup DHCP Server
    • View Active DHCP Leases
    • Reserve IP Addresses for Predetermined DHCP Clients
    • Delete DHCP Server Reservation
  • Setup WLAN
    • Configure the Basic Setup of the Wireless Mode
•  802.11b only
•  802.11b/g mixed
•  802.11g only
•  superG
  • Scan for Site Survey
  • View Link Information
  • Scan for Channel Survey
  • Align the Antenna
  • Configure the Advanced Setup of the Wireless Mode
  • View the Statistics
  • Setup Your WAN
  • Setup Telnet / SSH
    • Access the TELNET Command Line Interface
• You may connect to the CLI (Command Line Interface) via a TELNET session to the default IP 192.168.168.1 Microsoft TELNET command is shown here but any TELNET client can be used.
• 1. Enter C:\WINDOWS\TELNET 192.168.168.1 at DOS prompt and the TELNET application will launch and connect.
• 2. At the login prompt, type in the default password “password” and press enter. You will then login to the CLI.
  • Access the Secure Shell Host Command Line Interface
  • Set the WEB Mode
  • Use MAC Filtering
    • Add a MAC Address to the MAC Address List
    • Delete a MAC Address from All Access Points
    • Delete a MAC Address from Individual Access Point
    • Edit MAC Address from the MAC Address List
• Perform Advanced Configuration
  • Setup Routing
    • Configure Static Routing
  • Use Routing Information Protocol
  • Use Network Address Translation
    • Configure Virtual Servers Based on DMZ Host
    • Configure Virtual Servers Based on Port Forwarding
    • Configure Virtual Servers based on IP Forwarding
  • Control the Bandwidth Available
    • Enable Bandwidth Control
    • Configure WAN Bandwidth Control
    • Configure LAN Bandwidth Control
  • Perform Remote Management
    • Setup Remote Management
• Use Parallel Broadband
  • Enable Parallel Broadband
  • Setup Email Notification
  • Using Static Address Translation
  • Use DNS Redirection
    • Enable or Disable DNS Redirection
  • Dynamic DNS Setup
    • To enable/disable Dynamic DNS Setup
    • To manage Dynamic DNS List
• Use the Wireless Extended Features
  • Setup WDS2
• WDS2 (Wireless Distributed System 2) links up access points to create a wider network in which mobile users can roam while still staying connected to available network resources. The wireless client and root access point has to be set up with the same channel frequency. This allows them to connect even when the link is lost, as the channel frequency setting is preserved.
  • Set Virtual AP (Multiple SSID)
  • Set Preferred APs
    • Get Long Distance Parameters
  • Set Wireless Multimedia
• Wireless Multimedia (WMM) is a QoS (Quality of Service) standard in IEEE802.11E that we have adopted to improve and support the user experience for multimedia, video, and voice applications by prioritizing data traffic. QoS can be realized through 4 different Access Categories (AC). Each AC type consists of an independent transmit queue, and a channel access function with its own parameters.
  • Setup Point-to-Point & Point-to-MultiPoint Connection
  • Setup Repeater
• Secure your Wireless LAN
  • Setup WEP
•  Key 1
•  Key 2
•  Key 3
•  Key 4
•  Use Hexadecimal:
•  Use ASCII
•  64- bit WEP
• 10 hexadecimal or 5 ASCII Text
•  128-bit WEP
• 26 hexadecimal or 13 ASCII Text
  • Setup WPA-Personal
•  Passphrase (Alphanumeric characters)
•  Hexadecimal
  • Setup 802.1x/RADIUS for Access Point
•  64- bit
• 10 hexadecimal or 5 ASCII Text
•  128-bit
• 26 hexadecimal or 13 ASCII Text
  • Setup 802.1x/RADIUS for Client
  • Setup WPA Enterprise for Access Point
  • Setup WPA Enterprise for Client
• Configure the Security Features
  • Use Packet Filtering
    • Configure Packet Filtering
  • Use URL Filtering
    • Configure URL Filtering
  • Configure the Firewall
    • Configure SPI Firewall
  • Use the Firewall Log
    • View Firewall Logs
• Administer the System
  • Use the System Tools
    • Use the Ping Utility
    • Use Syslog
    • Setup System Clock
    • Upgrade the Firmware with uConfig
    • Upgrade the Firmware with Command Line Interface
    • Perform Firmware Recovery
    • Backup or Reset the Settings
    • Reboot the System
    • Change the Password
    • To Logout
  • Use the HELP menu
    • View About System
    • Get Technical Support
• Appendix: Use the Command Line Interface
• Appendix: Virtual AP (Multi-SSID) FAQ
• Appendix: View the Technical Specifications
  • Technical Support Information
    • Technical Support Centres