Document Outline

• Cover - Outer
• Cover - Inside
• TABLE OF CONTENTS
• TABLES
• FIGURES
• Preface
  • Customer Support
  • About this Manual
    • Reporting Comments or Suggestions Concerning this Manual
  • Conventions and References
    • Metric Conversion
    • Cautions and Warnings
    • Recommended Standard Designations
  • Electrical Safety
    • Fuses
    • Environmental
    • Installation
  • Telecommunications Terminal Equipment Directive
  • EMC (Electromagnetic Compatibility)
  • Warranty Policy
    • Limitations of Warranty
    • Exclusive Remedies
• Chapter 1. INTRODUCTION
  • 1.1 Overview
  • 1.2 Standard Features
    • 1.2.1 AUPC
    • 1.2.2 Software
    • 1.2.3 Verification
    • 1.2.4 Data Interfaces
  • 1.3 Options
  • 1.4 Compatibility
  • 1.5 Manual Release Notes
• Chapter 2. INSTALLATION
  • 2.1 Unpacking and Inspection
  • 2.2 Mounting
    • 2.2.1 Leading Particulars
  • 2.3 Configuration
  • 2.4 Select Internal IF Loop
  • 2.5 Connect External Cables
• Chapter 3. FUNCTIONAL DESCRIPTION
• Chapter 4. PHYSICAL DESCRIPTION
  • 4.1 Overview
  • 4.2 Front Panel
  • 4.3 Rear Panel
• Chapter 5. REAR PANEL CONNECTOR PINOUTS
  • 5.1 Connector Overview
  • 5.2 Data Interface Connector, DB-25F
  • 5.3 Alarms Connector, DB-15M
  • Auxiliary Serial Connector, HE1402 3-Pin Header
    • 5.5.1 Pin Numbering
• Ch05_RearPnlConns.pdf
• Chapter 6. FRONT PANEL OPERATION
  • 6.1 Introduction
    • 6.1.1 Front Panel Keypad
  • 6.2 Menu Trees
    • Opening Screen
    • SELECT: (Top level) Menu
    • 6.2.3 SELECT: CONFIG
      • 6.2.3.1 (CONFIG:) TX (Transmit)
        • 6.2.3.1.1 (CONFIG: TX) MOD (Modulation)
        • (CONFIG: TX) FREQ (Frequency)
        • 6.2.3.1.3 (CONFIG: TX) DATA (Data Rate)
        • 6.2.3.1.4 (CONFIG: TX) FEC TYPE (Forward Error Correction):
          • (CONFIG: TX, FEC)
          • (CONFIG: TX, FEC)
          • (CONFIG: TX, FEC, RATE) FEC Rate (Any FEC Type Except Turbo)
          • (CONFIG: TX, FEC, RATE) FEC Rate (Turbo Only)
        • (CONFIG: TX) ON/OFF
          • (CONFIG: TX ( PWR) MODE
          • (CONFIG: TX ( PWR ( MODE) MANUAL
          • (CONFIG: TX ( PWR ( MODE) AUPC
          • (CONFIG: TX ( PWR ( MODE) AUPC
          • (CONFIG: TX ( PWR ( MODE ( AUPC) TARGET EbNo
          • (CONFIG: TX ( PWR ( MODE ( AUPC) MAX RANGE
          • (CONFIG: TX ( PWR ( MODE ( AUPC) ALARM
          • (CONFIG: TX ( PWR ( MODE ( AUPC) DEMOD-UNLOCK
        • 6.2.3.1.6 (CONFIG: TX) SCRAM (Scrambling)
        • (CONFIG: TX) CLK (Clocking)
        • (CONFIG: TX) TSI (Transmit Spectral Invert)
      • (CONFIG:) RX (Receive)
        • (CONFIG: RX) MOD (Modulation)
        • (CONFIG: RX) FRQ (Frequency)
        • (CONFIG: RX) DATA (Data Rate)
        • 6.2.3.2.4 (CONFIG: RX) FEC TYPE (Forward Error Correction):
          • (CONFIG: RX ( FEC ( RATE) FEC RATE
          • (CONFIG: RX ( FEC ( RATE) FEC RATE (TURBO ONLY)
        • (CONFIG: RX) ACQ (Acquisition sweep range)
        • (CONFIG: RX) DESCRAM (Descrambler)
          • (CONFIG: RX) CLK (Clocking)
          • (CONFIG: RX) BUF (Buffer size)
        • (CONFIG: RX) RSI (Receive spectral inversion)
        • 6.2.3.2.8 (CONFIG: RX) Eb/No (Eb/No Alarm)
        • (CONFIG:) FRAME (Framing Mode)
        • 6.2.3.2.10 (CONFIG: FRAME) TRANSPARENT
        • 6.2.3.2.11 (CONFIG: FRAME) FRAMED
        • (CONFIG: FRAME ( FRAMED) EDMAC-ON
          • (CONFIG: FRAME( FRAMED( ON) EDMAC MASTER
          • (CONFIG: FRAME( FRAMED ( ON) EDMAC SLAVE
      • 6.2.3.3 (CONFIG:) INTFC (Interface)
      • (CONFIG:) REMCONT (Remote control)
        • 6.2.3.4.1 (CONFIG: LOCAL)
        • 6.2.3.4.2 (CONFIG: REMOTE)
        • 6.2.3.4.3 (CONFIG: REMOTE ( BAUD)
        • 6.2.3.4.4 (CONFIG: REMOTE ( INTFC)
          • (CONFIG: REM ( INTFC ( ADDR) RS232 BUS ADDRESS
          • (CONFIG: REM ( INTFC ( ADDR) RS485 BUS ADDRESS:
      • 6.2.3.5 (CONFIG:) MASK (Alarm mask)
        • (CONFIG: MASK) AGC
        • 6.2.3.5.2 (CONFIG:MASK) Eb/No
        • (CONFIG: MASK) RX-AIS
        • (CONFIG: MASK) BUF-SLIP (Buffer slip)
        • (CONFIG, MASK) TX-AIS
      • (CONFIG:) IMPED (IF impedance)
    • 6.2.4 SELECT: TEST
    • SELECT: INFO (Information)
      • (INFO) ID (Circuit ID)
      • (INFO) TX (Transmit information)
      • 6.2.5.3 (INFO) RX (Receive information)
      • (INFO) BUFF (Buffer information)
      • (INFO) EDMAC (Framing and EDMAC information)
      • (INFO) REMCONT (Remote Control information)
      • (INFO) MASK (Alarm mask information)
      • (INFO) MISC (Miscellaneous information)
    • 6.2.6 SELECT: MONIT (Monitor)
      • (MONIT:) ALARMS
        • (MONIT: ALARMS) UNIT (Unit alarms)
        • (MONIT: ALARMS) RECEIVE (Receive alarms)
        • (MONIT: ALARMS) TRANSMIT (Transmit alarms)
      • (MONIT:) RX-PARAMS (Receive Parameters)
      • (MONIT:) STORED EVENTS
        • (MONIT: EVENTS) VIEW
        • 6.2.6.3.2 (MONIT:) STATS (Link Statisics)
          • (MONIT: STATS) VIEW
          • (MONIT: STATS) CONFIGURE
      • 6.2.6.4 (MONITOR) AUPC
    • SELECT: STORE/LD (Store/Load)
      • (STORE/LD) STORE
      • (STORE/LD) LOAD
    • SELECT: UTIL (Utility)
      • 6.2.8.1.1 (UTIL:) SET-RTC (Set real-time clock)
      • (UTIL:) DISPLAY (Display brightness)
      • (UTIL:) MAN-1:1 (Manual 1:1 switchover)
      • 6.2.8.4 (UTIL:) RECENTER-BUF (Re-center buffer)
      • 6.2.8.5 (UTIL:) ID (Circuit ID)
• Chapter 7. FORWARD ERROR CORRECTION OPTIONS
  • 7.1 Introduction
  • 7.2 Viterbi
  • 7.3 Sequential
  • 7.4 Reed-Solomon Outer Codec (Option)
  • 7.5 Turbo Product Codec (Option)
    • 7.5.1 End-to-End Processing Delay
  • 7.6 Uncoded Operation (No FEC)
• Chapter 8. OFFSET QPSK OPERATION
• Chapter 9. RS-232 DATA INTERFACE - ASYNCHRONOUS OPERATION
  • 9.1 Introduction
  • 9.2 ASYNC EIA-232 Specifications
  • 9.3 Setup
  • 9.4 Other Considerations
    • 9.4.1 Baud Rate Accuracy
    • 9.4.2 Async Character Formats Using 1.5 Stop Bits
• Chapter 10. CLOCKING MODES
  • 10.1 Overview
  • 10.2 Transmit Clocking
    • 10.2.1 Internal Clock
    • 10.2.2 External Clock
    • 10.2.3 Loop-Timed, RX=TX
    • 10.2.4 Loop-Timed, RX<>TX (Asymmetric Loop Timing)
  • 10.3 Receive Clocking
    • 10.3.1 Buffer Disabled
    • 10.3.2 Buffer Enabled, RX=TX
    • 10.3.3 Buffer Enabled, RX<>TX
  • 10.4 X.21 Notes
  • 10.5 Loop Timing with Sync RS-232
• Chapter 12. AUTOMATIC UPLINK POWER CONTROL
  • 12.1 Introduction
  • 12.2 Setting AUPC Parameters
    • 12.2.1 Target Eb/No
    • 12.2.2 Max Range
    • 12.2.3 Alarm
    • 12.2.4 Demod Unlock
  • 12.3 Compensation Rate
  • 12.4 Monitoring
• Chapter 11. EDMAC CHANNEL
  • 11.1 Theory of Operation
  • 11.2 M&C Connection
  • 11.3 Setup Summary
• Chapter 13. FLASH UPGRADING
• Chapter 14. SUMMARY OF SPECIFICATIONS
• Chapter 15. REMOTE CONTROL
  • 15.1 Introduction
  • 15.2 RS-485
  • 15.3 RS-232
  • 15.4 Basic Protocol
  • 15.5 Packet Structure
    • 15.5.1 Start Of Packet
    • 15.5.2 Address
    • 15.5.3 Instruction Code
    • 15.5.4 Instruction Code Qualifier
    • 15.5.5 Message Arguments
    • 15.5.6 End Of Packet
  • 15.6 Remote Commands and Queries
    • 15.6.1 Transmit (Tx) Commands and Queries
    • 15.6.2 Receive (Rx) Commands and Queries
    • 15.6.3 Unit Remote Commands and Queries
    • 15.6.4 Remote Queries
    • 15.6.5 Bulk Commands
• Appendix A. CABLE DRAWINGS
  • A.1 Overview
    • A.1.1 RS-530 to RS-422/449 Data Cable
    • A.1.2 RS-530 to V.35 Data Cable
    • A.1.3 RS-232 Remote Control Cable
• Appendix B. Eb/No MEASUREMENT
• Appendix C. ASYNC OVERHEAD OPTION
  • C.1 Introduction
  • C.2 Electrical Interface
  • C.3 Pin Numbering
  • C.4 Baud Rates
  • C.5 Selecting Async Mode
• Appendix D. KST-2000A FSK (ODU) REMOTE OPERATION
  • D.1 ODU Operation via a CDM-550T Modem Front Panel Comprising Firmware ( 1.20
    • D.2.1 SELECT: (Top level) Menu
    • D.2.2 SELECT: ODU
      • D.2.2.1 (ODU:) ENABLE Selections
        • D.2.2.1.1 (ODU:) ENABLE ( CONFIG (Configuration)
          • D.2.2.1.1.1 (ODU:) ENABLE ( CONFIG ( TRANSMITTER
    • (ODU:) ENABLE ( CONFIG ( TRANSMITTER (FREQUENCY
    • (ODU:) ENABLE ( CONFIG ( TRANSMITTER ( ATTEN (Attenuation)
    • (ODU:) ENABLE ( CONFIG ( TRANSMITTER ( OUTPUT
    • (ODU:) ENABLE ( CONFIG ( TRANSMITTER ( HPA
    • (ODU:) ENABLE ( CONFIG ( TRANSMITTER ( HPA ( STATE
    • (ODU:) ENABLE ( CONFIG ( TRANSMITTER ( HPA (FAULT- LOGIC
      • D.2.2.1.1.2 (ODU:) ENABLE (CONFIG ( RECEIVER
        • (ODU:) ENABLE (CONFIG ( RECEIVER ( FREQUENCY
    • (ODU:) ENABLE (CONFIG ( RECEIVER ( ATTEN (Attenuation)
    • (ODU:) ENABLE (CONFIG ( RECEIVER ( LNA
    • (ODU:) ENABLE (CONFIG ( RECEIVER ( LNA ( STATE
    • (ODU:) ENABLE (CONFIG ( RECEIVER ( LNA ( CAL (Calibrate)
    • (ODU:) ENABLE (CONFIG ( RECEIVER ( LNA ( FAULT- LOGIC
      • D.2.2.1.1.3 (ODU:) ENABLE ( CONFIG ( MISC (Miscellaneous)
    • (ODU:) ENABLE ( CONFIG ( MISC ( AGC (Auto Gain Control)
    • (ODU:) ENABLE ( CONFIG ( MISC ( REF-ADJUST
      • D.2.2.1.2 (ODU: ) ENABLE ( INFO (Information)
    • (ODU: ) ENABLE ( INFO ( TRANSMITTER
    • (ODU: ) ENABLE ( INFO ( RECEIVER
    • (ODU: ) ENABLE ( INFO ( HPA
    • (ODU: ) ENABLE ( INFO ( LNA
    • (ODU: ) ENABLE ( INFO ( EQUIP (Equipment)
    • (ODU: ) ENABLE ( INFO ( EQUIP ( ASSEMBLY+SN
    • (ODU: ) ENABLE ( INFO ( FW (Firmware)
      • D.2.2.1.3 (ODU: ) ENABLE ( STATUS
• METRIC CONVERSIONS
• BackCover