Document Outline

• mn-crs150_r2.pdf
  • INSIDE COVER
  • TABLE OF CONTENTS
  • TABLES
  • FIGURES
  • PREFACE
    • About this Manual
      • Reporting Comments or Suggestions Concerning this Manual
    • Related Documents
    • Conventions and References
      • Warnings, Cautions, and Notes
      • Metric Conversion
      • Recommended Standard Designations
      • Trademarks
    • Electromagnetic Compatibility (EMC) Compliance
      • EN 55022-1997 Compliance
      • EN 50082-1:1998 Compliance
    • Safety Compliance
      • EN 60950
      • Electrical Safety
      • Equipment Connection
      • European Low Voltage Directive (LVD)
      • Federal Communications Commission (FCC)
      • Telecommunications Terminal Equipment Directive
      • Environmental
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
    • Customer Support
      • Online Customer Support
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Description of Features
    • 1.3 Functional Description
    • 1.4 Summary of Specifications
    • 1.5 Dimensional Envelope
  • Chapter 2. INSTALLATION
    • Unpacking and Inspecting the Shipment
    • 2.2 Rack-Mounting the CRS-150
  • Chapter 3. CONNECTOR PINOUTS
    • 3.1 Connector Overview
    • 3.2 Front Panel Connectors
      • 3.2.1 Front Panel IF Connectors – Receive IF and Transmit IF, 50Ω BNC
      • 3.2.2 Front Panel Terrestrial Data Connectors
        • 3.2.2.1 Overhead Data Connector, DB-25M
        • 3.2.2.2 Data Interface Connector, DB-25F
        • 3.2.2.3 Audio Connector, DB-9F
        • 3.2.2.4 G.703 Connectors
          • 3.2.2.4.1 Balanced G.703 Interface Connector, DB-15F
          • 3.2.2.4.2 Rx and Tx (Unbalanced) G.703 Connectors, 75Ω BNC
          • 3.2.2.4.3 IDI, DDO Connectors, 75Ω BNC
      • 3.2.3 Front Panel Utility Connectors
        • 3.2.3.1 Ext Ref, 50Ω BNC
        • 3.2.3.2 IDR Alarms Connector, DB-15F
      • 3.2.4 Front Panel Power Connections – Aux DC Inputs
    • 3.3 Rear Panel Connectors
      • 3.3.1 Rear Panel IF Connectors – Receive IF and Transmit IF A/B, 50Ω BNC
      • 3.3.2 Rear Panel Terrestrial Data Connectors
        • Balanced G.703 A and B Connectors, DB-15M
        • 3.3.2.2 Audio A and B Connectors, DB-9F
        • 3.3.2.3 Overhead Data A and B Connectors, DB-25M
        • 3.3.2.4 Data Interface A and B Connectors, DB-25F
      • 3.3.3 Rear Panel Utility Connectors
        • 3.3.3.1 IDR Alarms A and B Connectors, DB-15F
        • 3.3.3.2 Aux Serial A and B Receptacles, USB Type ‘A’
        • 3.3.3.3 Ext Ref A and B Connectors, 50Ω BNC
      • 3.3.4 Ground Connection
    • 3.4 Data Interface Converter Modules / Adapters
      • 3.4.1 CIC-20 HSSI Connector, HD-50F
      • 3.4.2 CIC-35 ASI Connectors, 75Ω BNC
      • 3.4.3 E1/T1 RJ-48 Connection via Balanced G.703 Interface Connector
  • Chapter 4. CABLES AND CONNECTIONS
    • 4.1 Overview
    • 4.2 Cabling to the CDM-600
      • 4.2.1.1 CRS-150 Accessories
      • 4.2.2 Modem-to-Switch Control Interface Connection
      • 4.2.3 Modem-to-Switch IF Interface Connection
      • 4.2.4 Modem-to-User Utility Interface Connection and Examples
        • 4.2.4.1 IDR Alarms Data Interface Example
        • 4.2.4.2 External Reference Data Interface Example
      • 4.2.5 Modem-to-User Data Interface Connection and Examples
        • 4.2.5.1 RS-422/232 Interface Example
        • 4.2.5.2 HSSI Data Interface Example
        • 4.2.5.3 G.703 Balanced Interface Example
        • 4.2.5.4 G.703 Unbalanced Interface Example
        • 4.2.5.5 ASI Data Interface Example
        • 4.2.5.6 E1/T1 Data Interface Example
        • 4.2.5.7 Overhead Data Interface Example
        • 4.2.5.8 Audio Data Interface Example
    • 4.3 Cabling to the CDM-600L (CLM-9600L)
  • Chapter 5. MODEM AND SWITCH CONFIGURATION
    • 5.1 Overview
    • 5.2 Configuration of CDM-600s for 1:1 Redundancy
      • 5.2.1 Automatic Redundant Operation
      • 5.2.2 Manual Redundant Operation (Forced Switchover)
        • 5.2.2.1 Forced Switchover via the CDM-600 Front Panel
        • 5.2.2.2 Forced Switchover via Remote Bus
      • 5.2.3 Replacement of Standby Unit
    • 5.3 CRS-150 Switch DIP Settings
  • Appendix A. CABLE DRAWINGS
    • A.1 Introduction
    • A.2 Control Interface Cables
      • A.2.1 Modem-to-Switch Auxiliary Serial Cable (1:1 Control), USB Type A ( USB Type B
      • A.2.2 Modem-to-Switch (CRS-150 ( CRS-170A) Control/Data ‘Y’ Cable, DB-25M ( DB-25M, DB-9M (CDM600L [CDM-9600L])
    • A.3 IF / Utility / Data Interface Cables
      • A.3.1 Modem-to-Switch/User IF (70/140 MHz) Coax Cable, Type ‘BNC’ 50Ω
      • A.3.2 Modem-to-Switch Data Cable, DB-15M ( DB-15M
      • A.3.3 Modem-to-Switch Coax Cable, Type ‘BNC’ 75Ω
      • A.3.4 Modem-to-Switch Universal Control/Data Cable, DB-25M ( DB-25M
      • A.3.5 Modem-to-Switch Universal Control/Data Cable, DB-15M ( DB-15M
      • A.3.6 Modem-to-Switch Data Cable, DB-25M ( DB-25M
      • A.3.7 Modem-to-Switch Data Cable, DB-9M ( DB-9M
  • METRIC CONVERSIONS
• BACK COVER