Document Outline

• KST-12000 Rev 4
• Customer Service
• Table of Contents
• Preface
  • About this Manual
  • Conventions and References
    • Metric Conversion
    • Cautions and Warnings
    • Reporting Comments or Suggestions Concerning this Manual
  • Electrical Safety
    • Fuses
    • Environmental
    • Installation
  • Telecommunications Terminal Equipment Directive
  • EMC (Electromagnetic Compatibility)
  • Warranty Policy
    • Limitations of Warranty
    • Exclusive Remedies
    • Disclaimer
• 1. INTRODUCTION
  • 1.1 Description
    • 1.1.1 Applications
    • 1.1.2 Monitor and Control
    • 1.1.3 Low Noise Amplifier (LNA)
    • 1.1.4 Outdoor Enclosure
  • 1.2 Options
    • 1.2.1 Configurations
    • 1.2.2 Equipment
  • 1.3 Specifications
• 2. SINGLE-THREAD SYSTEM INSTALLATION
  • 2.1 Unpacking
  • 2.2 Inspecting the Equipment
    • 2.2.1 Included Parts
  • 2.3 RFT Installation
    • 2.3.1 Tools Required
    • 2.3.2 Vertical Pole Installation
      • 2.3.2.1 Round Pole
      • 2.3.2.2 Square Pole
    • 2.3.3 Spar Installation
  • 2.4 LNA and Flexible Waveguide Installation
  • 2.5 External Connections
    • 2.5.1 TX/IF Input (J1)
    • 2.5.2 TX/RF Output (J2)
    • 2.5.3 RX/IF Output (J3)
    • 2.5.4 RX/RF Input (J4)
    • 2.5.5 Prime Power (J5)
    • 2.5.6 Serial Remote Control (J6)
    • 2.5.7 GND
• 3. REDUNDANT SYSTEM INSTALLATION
  • 3.1 Unpacking
  • 3.2 Inspecting the Equipment
    • 3.2.1 Included Parts
  • 3.3 RFT Installation
    • 3.3.1 Tools Required
    • 3.3.2 Vertical Pole Installation
      • 3.3.2.1 Round Pole
      • 3.3.2.2 Square Pole
    • 3.3.3 Spar Installation
    • 3.3.4 1:1 Redundant Plate Installation
    • 3.3.5 Waveguide Switch Installation
  • 3.4 RSU-503L Installation
  • 3.5 External Connections
• 4. OPERATION
  • 4.1 System Operation
  • 4.2 Remote Control
  • 4.3 Front Panel Display/Keypad
    • 4.3.1 Front Panel Controls
    • 4.3.2 Menu Explanations
      • 4.3.2.1 Configuration
      • 4.3.2.2 Monitor
      • 4.3.2.3 Faults
• 5. THEORY OF OPERATION
  • 5.1 Monitor and Control
    • 5.1.1 EEPROM Memory
    • 5.1.2 Remote Interface
      • 5.1.2.1 Remote Interface Specification
    • 5.1.3 Terminal Default Conditions
    • 5.1.4 Theory of Operation
    • 5.1.5 M&C Board Connector Pinouts
      • 5.1.5.1 RS-232/485 Remote Control (J1)
      • 5.1.5.2 Remote Relay Control, J2 DB15-Female
      • 5.1.5.3 HPA, PS, U/C and D/C, J3 DB37-Male
      • 5.1.5.4 Synthesizers (DC/UC/LO), J4 DB37-Female
      • 5.1.5.5 Keypad Display, 24-Pin (12 x 2) Ribbon Connector (J5)
    • 5.1.6 Test Points and LEDs
  • 5.2 High Stability Oscillator
    • 5.2.1 Specifications
  • 5.3 IF Local Oscillator
    • 5.3.1 Specifications
  • 5.4 Synthesizer
    • 5.4.1 Specifications
    • 5.4.2 Theory of Operation
  • 5.5 Down Converter
    • 5.5.1 Specifications
    • 5.5.2 Theory of Operation
  • 5.6 Up Converter
    • 5.6.1 Specifications
    • 5.6.2 Theory of Operation
• 6. MAINTENANCE
  • 6.1 Test Points and LEDs
  • 6.2 Fault Isolation
• A. REMOTE CONTROL OPERATION
  • A.1 General
  • A.2 Message Structure
    • A.2.1 Start Character
    • A.2.2 Device Address
    • A.2.3 Command/Response
    • A.2.4 End Character
  • A.3 Configuration Commands/Responses
  • A.4 Status Commands/Responses
• Glossary