Document Outline

• KST-2000AB REV 9
• Customer Service
• Preface
  • About this Manual
    • Trademarks
  • Warnings and Cautions
    • Reporting Comments or Suggestions Concerning this Manual
    • Related Documents
  • Installation Guidelines Regarding Power Line Quality
  • Warranty Policy
• 1. INTRODUCTION
  • 1.1 Description
    • 1.1.1 Receive Reject Filter
    • 1.1.2 Recommended Maintenance
    • 1.1.3 Areas of Operation:
    • 1.1.4 Features
    • 1.1.5 Single-Thread KST 2000A System
    • 1.1.6 Single-Thread KST 2000B System
    • 1.1.7 Redundant System
  • 1.2 Specifications
• 2. INSTALLATION
  • Single-Thread System Components
  • 2.2. Redundant System Components
  • 2.3. Description of Options
  • 2.4. Electrical Connections
    • 2.4.1. Converter Unit
    • 2.4.2. Data SSPAs
    • LNA Connections
    • LNB Connections
• 3. OPERATION
  • 3.1 Initial Setup (Single-Thread System)
    • 3.1.1 Uplink Setup
    • 3.1.2 Downlink Setup
  • 3.2 Initial Setup Redundant System
  • 3.3 Redundant Junction Unit Description
    • 3.3.1 3.3.1 RJU 2000 Description
  • 3.4 Connector Descriptions
    • 3.4.1 TX Switch Connector (J1)
    • 3.4.2 RX Switch Connector (J2)
    • 3.4.3 1:1 Interface Connector (J3)
    • 3.4.4 RFTA Remote Interface Connector (J4)
    • 3.4.5 RFTB Remote Interface Connector (J5)
    • 3.4.6 Interface M&C Connector (J6)
    • 3.4.7 Other Connectors
  • 3.5 Indicators Description
  • 3.6 1:1 Redundant KST 2000A/B System Operation
  • 3.7 Reference Oscillator
  • 3.8 Monitor and Control (M&C)
    • 3.8.1 Up Converter Description
  • 3.9 Ku- to L Band Down Converter Description (KST 2000A)
  • 3.10 L Band to IF Down Converter Description (KST 2000A/B)
  • 3.11 Automatic Gain Control (AGC)
    • 3.11.1 Operation
    • 3.11.2 Fault and Error Response
    • 3.11.3 Manual Gain Operation
• 4. FAULT INDICATION AND ISOLATION
  • 4.1 Fault Indication
  • 4.2 Fault Isolation
  • 4.3 Stored Faults
• 5. KEYPAD / DISPLAY
  • 5.1 Keypad/Display Overview
  • 5.2 Front Panel Keypad/Display
    • 5.2.1 Front Panel Controls
  • 5.3 The Menu Structure
  • 5.3.1 Configuration
  • 5.3.2 Monitor
  • 5.3.3 Faults
  • 5.3.4 Utility
  • 5.3.5 System
    • 5.3.6 Redundancy
• A. EQUIPMENT OUTLINE DRAWINGS
  • A.1 2 and 4 Watt SSPA Equipment Outline
  • A.2 8 Watt SSPA Equipment Outline
  • 16 Watt SSPA Equipment Outline
  • A.4 25/32/40 Watt SSPA Equipment Outline
  • Ku Band LNA Equipment Outline
  • KST 2000A/B Converter Equipment Outline
  • A.7 Ku-Band LNB Equipment Outline
• B. TERMINAL MODE COMMANDS
  • B.1 General
  • B.2 Message Structure
    • B.2.1 Start Character
    • B.2.2 Device Address
    • B.2.3 Command/Response
    • B.2.3 End Character
  • B.3 System Configuration Commands
    • B.3.1 Configuration Commands/Responses
    • B.3.2 System Configuration Commands
    • B.3.3 Reset Commands
    • B.3.4 Status Commands/Responses
  • B.3.5 Stored Faults
    • B.3.6 Miscellaneous
  • B.4 Backup Operations/Self-Contained Redundancy
    • B.4.1 External Fault Mode
    • B.5 Keypad/Display Related Commands
• C. SINGLE-THREAD EQUIPMENT MOUNTING
  • C.1 Tools Required
  • C.2 Converter Unit Installation
    • Spar Arm Mount
    • C.2.2 Pole Mount
  • C.3 SSPA Installation
    • C.3.1 Feed Mount Offset Antenna
  • C.4 LNA Installation
    • C.4.1 Feed Mount Offset Antenna
  • C.5 Cable Installation
• D. REDUNDANT EQUIPMENT MOUNTING
  • D.1 Tools Required
  • D.2 1:1 Converters Installation
    • D.2.1 Spar Arm Mount
    • D.2.2 Pole Mount
  • D.3 1:1 SSPA Installation
    • D.3.1 Feed Mount Offset Antenna
  • D.4 1:1 LNA Installation
    • D.4.1 Feed Mount Offset Antenna
  • D.5 Cable Installation
• E. FSK REMOTE CONTROL COMMANDS
  • E.1 Introduction
  • E.2 Basic Protocol
    • E.2.1 Packet Structure
    • E.2.2 Start Of Packet
    • E.2.3 Address
    • E.2.4 Instruction Code
    • E.2.5 Instruction Code Qualifier
    • E.2.6 Message Arguments
    • E.2.7 End Of Packet
  • E.3 Commands and Query
• GLOSSARY
• INDEX