Document Outline

• mn-mbt4000_r4.pdf
  • INSIDE COVER
  • Errata A
  • TABLE OF CONTENTS
  • TABLES AND FIGURES
  • PREFACE
    • About this Manual
      • New in this Release
      • Reporting Comments or Suggestions Concerning this Manual
    • Conventions and References
      • Cautions and Warnings
      • Recommended Standard Designations
      • Trademarks
      • Metric Conversion
    • Electromagnetic Compatibility (EMC) Compliance
      • EN 55022 –1998 Compliance
      • EN 55082-1 – 1997 Compliance
      • Federal Communications Commission (FCC)
    • Safety Compliance
      • EN 60950 – 1997 Compliance
      • Low Voltage Directive (LVD)
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
    • Customer Support
      • Online Customer Support
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 Common Features
    • 1.4 Options
    • 1.5 System Overview
    • 1.6 Summary of Specifications
      • 1.6.1 Environmental & Physical
      • 1.6.2 BUC-4000 Block Up Converter ODU
      • 1.6.3 BDC-4000 Block Down Converter ODU
    • 1.7 Dimensional Envelope
  • Chapter 2. INSTALLATION
    • 2.1 Unpacking and Inspection
    • 2.2 Installation
    • 2.3 Operation
  • Chapter 3. EXTERNAL CONNECTORS
    • 3.1 External Connectors Overview
    • 3.2 MBT-4000 External Connectors
      • 3.2.1 IF Signal Side Connectors
        • 3.2.1.1 POWER (J1)
        • 3.2.1.2 COMM (J2)
        • 3.2.1.3 UNIT 1 COMM (J3)
        • 3.2.1.4 IF Switch (J4)
        • 3.2.1.5 Ext Ref (External Reference) (J5)
        • 3.2.1.6 UNIT 2 COMM (J6)
        • 3.2.1.7 Ground Connector
        • 3.2.1.8 IF IN (J4, BUC-4000 ONLY)
        • 3.2.1.9 COMM (J6, BUC-/BDC-4000)
        • 3.2.1.10 IF OUT (J4, BDC-4000 ONLY)
      • 3.2.2 RF Signal Side Connectors
        • 3.2.2.1 REDUNDANT LOOP (J7)
        • 3.2.2.2 AUX COMM 2 (J8)
        • 3.2.2.3 AUX COMM 1 (J9)
        • 3.2.2.4 RF SWITCH (J10)
        • RF OUT (J5, BUC-4000 ONLY)
        • 3.2.2.6 RF IN (J5, BDC-4000 ONLY)
  • Chapter 4. SYSTEM OPERATING PARAMETERS
    • 4.1 Overview
    • 4.2 Remote Configuration, Monitoring and Control
    • 4.3 Block Up Converter Module (BUC-4000) Operating Parameters
    • 4.4 Block Down Converter Module (BDC-4000) Operating Parameters
    • 4.5 Monitoring Operations via the LED Indicators
  • Chapter 5. FLASH UPGRADING
    • 5.1 Overview
    • 5.2 Flash Upgrading via Internet
      • 5.2.1 Firmware File Transfer Procedure
    • 5.3 Flash Upgrade Procedure
  • Appendix A. REMOTE CONTROL
    • A.1 Overview
    • A.2 RS-485
    • A.3 RS-232
    • A.4 Basic Protocol
    • A.5 Packet Structure
      • A.5.1 Start of Packet
      • A.5.2 Target Address
      • A.5.3 Address Delimiter
      • A.5.4 Instruction Code
      • A.5.5 Instruction Code Qualifier
      • A.5.6 Optional Message Arguments
      • A.5.7 End of Packet
    • A.6 Remote Commands and Queries
  • Appendix B. FAULTS/EVENTS
    • B.1 LED Status Indicators
    • B.2 Faults/Events
      • B.2.1 Summary Faults
      • B.2.2 Configurable Summary Faults
      • B.2.3 Informational Events
  • Appendix C. REDUNDANCY CONFIGURATION / OPERATION
    • C.1 Overview
    • C.2 Single-Base Redundancy Operation
    • C.3 Dual-Base (Chain) Redundancy Operation
    • C.4 External Fault Monitoring
    • C.5 LNA Power Supply Current Monitoring
    • C.6 Gain Equalization of Redundant Units
    • C.7 Operational Configuration Commands
  • METRIC CONVERSIONS
  • BACK COVER