Document Outline

• MN-MBT5000_4 .pdf
  • INSIDE COVER
  • TABLE OF CONTENTS
  • TABLES AND FIGURES
  • PREFACE
    • About this Manual
      • Disclaimer
    • Conventions and References
      • Patents and Trademarks
      • Warnings, Cautions, and Notes
      • Examples of Multi-Hazard Notices
      • Recommended Standard Designations
    • Safety and Compliance
      • Electrical Safety and Compliance
      • Electrical Installation
      • Operating Environment
      • European Union Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive (1999/5/EC) and EN 301 489-1
        • European Union Electromagnetic Compatibility (EMC) Directive (2004/108/EC)
        • European Union Low Voltage Directive (LVD) (2006/95/EC)
        • European Union RoHS Directive (2002/95/EC)
        • European Union Telecommunications Terminal Equipment Directive (91/263/EEC)
        • CE Mark
    • Product Support
    • Comtech EF Data Headquarters
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 Features
      • 1.3.1 Block Upconverter (BUC-5000x)
      • 1.3.2 Block Downcoverter (BDC-5000x)
    • 1.4 Summary of Specifications
      • 1.4.1 Physical & Environmental
      • 1.4.2 Prime Power
      • 1.4.3 Monitor & Control
      • 1.4.4 Reference
      • 1.4.5 BUC-5000x Block Upconverters
      • 1.4.6 BDC-5000x Block Downconverters
    • 1.5 Dimensional Envelope
  • Chapter 2. INSTALLATION
    • 2.1 Unpack and Inspect the Shipment
    • 2.2 Install the Unit Into a Rack Enclosure
      • 2.2.1 Install the Optional Rear-Mounting Support Brackets Kit
      • 2.2.2 Install the Optional Bearingless Rack Slide Set
  • Chapter 3. REAR PANEL CONNECTIONS
    • 3.1 Cabling Connection Types
      • 3.1.1 Coaxial Cable Connections
        • 3.1.1.1 Type ‘BNC’
        • 3.1.1.2 Type ‘TNC’
        • 3.1.1.3 Type ‘N’
        • 3.1.1.4 Type ‘F’
        • 3.1.1.5 Type ‘SMA’ (Subminiature Version ‘A’)
      • 3.1.2 D-Subminiature Cable Connections
      • 3.1.3 /RJ-45, RJ-48 Cable Connections
    • 3.2 MBT-5000 Cabling Connections
      • 3.2.1 IF Connector Group
        • 3.2.1.1 ‘J4 | IF OUT/IN’ (Side B) Connector (Type ‘N’ Female)
        • 3.2.1.2 ‘J5 | RF IN/OUT’ (Side B) Connector (Type ‘N’ Female)
        • 3.2.1.3 ‘J6 | IF OUT/IN’ (Side A) Connector (Type ‘N’ Female)
        • 3.2.1.4 ‘J7 | RF IN/OUT’ (Side A) Connector (Type ‘N’ Female)
      • 3.2.2 Optional Redundancy Groups
        • 3.2.2.1 Optional ‘RF’ Connectors (Type ‘SMA’ Female)
        • 3.2.2.2 Optional ‘IF’ Connectors (Type ‘SMA’ Female)
      • 3.2.3 Utility Connector Group
        • 3.2.3.1 ‘J2 | EXT REF IN’ – External Reference Input Connector (BNC-F)
        • 3.2.3.2 ‘J8 | EXT REF OUT’ – External Reference Output Connector (BNC-F)
        • 3.2.3.3 ‘J9 | 10/100 ETHERNET’ 10/100 BaseT M&C Port (RJ-45)
        • 3.2.3.4 ‘P1 | RELAY’ Summary Fault Output Connector (DB-9F)
        • 3.2.3.5 ‘J1 | COM 1’ EIA-485/232 Interface Connector (DB-9F)
    • 3.3 MBT-5000 Ground and Power Connections
      • 3.3.1 Chassis Ground Interface
      • 3.3.2 Alternating Current (AC) Power Interfaces
        • 3.3.2.1 Standard 90-260V Alternating Current (AC) Power Interface
          • 3.3.2.1.1 Standard 90-260V AC Operation – Apply Power
          • 3.3.2.1.2 Standard 90-260V AC Operation – Replace the Fuses
        • 3.3.2.2 Optional Dual Entry Module Alternating Current (AC) Power Interface (Redundancy Units Only)
      • 3.3.3 Optional -48V Direct Current (DC) Power Interface
        • 3.3.3.1 Optional -48V DC Operation – Apply Power
        • 3.3.3.2 Optional -48V DC Operation – Replace the Fuse
  • Chapter 4. UPGRADING FIRMWARE
    • 4.1 Overview
      • 4.1.1 About Firmware Files Naming, Versions, and Formats
    • 4.2 Getting Started: Prepare for the Firmware Download
      • 4.2.1 Download and Extract the Firmware Update
      • 4.2.2 Perform the Ethernet FTP Upload Procedure
  • Chapter 5. FRONT PANEL OPERATION
    • 5.1 Overview
      • 5.1.1 Switch Power On (Rear Panel)
      • 5.1.2 LED Indicators
      • 5.1.3 Keypad
      • 5.1.4 Vacuum Fluorescent Display (VFD)
        • 5.1.4.1 Screen Saver
        • 5.1.4.2 Opening Screen
    • 5.2 Front Panel Operation
      • 5.2.1 SELECT: (Main) Menu
      • 5.2.2 SELECT: Config (Configuration) Menu Branches
        • 5.2.2.1 CONFIG: Remote (Remote Control) Menus
          • 5.2.2.1.1 Remote Control: Local
          • 5.2.2.1.2 Remote Control: Serial
          • 5.2.2.1.3 Remote Control: Ethernet
        • 5.2.2.2 CONFIG: FltRec (Fault Recovery) Menu
        • 5.2.2.3 CONFIG: ConvA or ConvB (Converter ‘A’ or Converter ‘B’) Menus
          • 5.2.2.3.1 Converter X: Mute/Freq
          • 5.2.2.3.2 Converter X: Attenuation
        • 5.2.2.4 CONFIG: RefAdj (Reference Oscillator Adjustment) Menu
        • 5.2.2.5 CONFIG: Redun (Redundancy) Menus
          • 5.2.2.5.1 Redundancy Mode: Disable/Enable
          • 5.2.2.5.2 Redundancy Mode: Force
      • 5.2.3 SELECT: Monitor Menu Branch
        • 5.2.3.1 Monitor: Faults
        • 5.2.3.2 Monitor: Mask
          • 5.2.3.2.1 Out-of-Range Power Supply Masking Using the PS Submenu
        • 5.2.3.3 Monitor: Event-Log (Stored Events)
          • 5.2.3.3.1 Stored Events: View
          • 5.2.3.3.2 Stored Event: Clear-All
        • 5.2.3.4 Monitor: LPT (Low Power Threshold)
      • 5.2.4 SELECT: Info (Information) Menu Branch
        • 5.2.4.1 INFO: Remote (Remote Control)
        • 5.2.4.2 INFO: ConvA (Converter ‘A’) or ConvB (Converter ‘B’)
        • 5.2.4.3 INFO: PSA or PSB (Power Supply ‘A’ or Power Supply ‘B’)
        • 5.2.4.4 INFO: RefOsc (Reference Oscillator)
      • 5.2.5 SELECT: Utility Menu Branch
        • 5.2.5.1 UTILITY: Date/Time (Set Real-time Clock)
        • 5.2.5.2 UTILITY: CID (Circuit ID)
        • 5.2.5.3 UTILITY: Display (VFD Display Brightness)
        • 5.2.5.4 UTILITY: Firmware
          • 5.2.5.4.1 Firmware Images: Info
          • 5.2.5.4.2 Firmware Images: Select
        • 5.2.5.5 UTILITY: LNA
          • 5.2.5.5.1 LNA: ConvX (ConvA or ConvB)
      • 5.2.6 SELECT: Test Menu Branch
  • Chapter 6. ETHERNET-BASED REMOTE PRODUCT MANAGEMENT
    • 6.1 Overview
    • 6.2 Ethernet Management Interface Protocols
    • 6.3 SNMP Interface
      • 6.3.1 Management Information Base (MIB) Files
      • 6.3.2 SNMP Community Strings
      • 6.3.3 SNMP Traps
    • 6.4 Telnet Interface
      • 6.4.1 Telnet Operation via HyperTerminal
    • 6.5 HTTP (Web Server) Interface
      • 6.5.1 Enable the Web Server Interface
      • 6.5.2 User Login
      • 6.5.3 Web Server Interface – Operational Features
        • 6.5.3.1 Navigation
        • 6.5.3.2 Page Sections
        • 6.5.3.3 Action Buttons
        • 6.5.3.4 Drop-down Lists
        • 6.5.3.5 Text or Data Entry
      • 6.5.4 Web Server Interface – Menu Tree
      • 6.5.5 Web Server Interface – Page Descriptions
        • 6.5.5.1 Home Pages
          • 6.5.5.1.1 Home | Home
          • 6.5.5.1.2 Home | Contact / Home | Support
        • 6.5.5.2 Admin Pages
          • 6.5.5.2.1 Admin | Access
          • 6.5.5.2.2 Admin | SNMP
        • 6.5.5.3 Config Pages
          • 6.5.5.3.1 Config | MBT
          • 6.5.5.3.2 Config | Utility
          • 6.5.5.3.3 Config | Redundancy
        • 6.5.5.4 Status Pages
          • 6.5.5.4.1 Status | Events
          • 6.5.5.4.2 Status | Status
  • Chapter 7. SERIAL-BASED REMOTE PRODUCT MANAGEMENT
    • 7.1 Overview
      • 7.1.1 EIA-485
      • 7.1.2 EIA-232
    • 7.2 Remote Commands and Queries Overview
      • 7.2.1 Basic Protocol
      • 7.2.2 Packet Structure
        • 7.2.2.1 Start of Packet
        • 7.2.2.2 Target Address
        • 7.2.2.3 Address Delimiter
        • 7.2.2.4 Instruction Code
        • 7.2.2.5 Instruction Code Qualifier
        • 7.2.2.6 Optional Message Arguments
        • 7.2.2.7 End of Packet
    • 7.3 Remote Commands and Queries
      • 7.3.1 MBT-5000 Base Unit Remote Commands and Queries
      • 7.3.2 Block Converter (BUC / BDC) Remote Commands and Queries
  • Appendix A. BUC-5000x/BDC-5000x MODULE REMOVAL/INSTALLATION
    • A.1 Overview
    • A.2 Module Removal Procedure
    • A.3 Module Installation Procedure
  • Appendix B. MBT-5000 REDUNDANCY OPERATION
    • B.1 Overview
    • B.2 Configuration
• BACK COVER