Document Outline

• mn-mbt5003_r1.pdf
  • INSIDE COVER
  • Table of Contents
  • Tables
  • Figures
  • PREFACE
    • About this Manual
      • Reporting Comments or Suggestions Concerning this Manual
    • Conventions and References
      • Cautions and Warnings
      • Recommended Standard Designations
      • Trademarks
      • Metric Conversion
    • Electromagnetic Compatibility (EMC) Compliance
      • EN55022 –1998 Compliance
      • EN55082-1 – 1997 Compliance
      • Federal Communications Commission (FCC)
    • Safety Compliance
      • EN60950
      • Low Voltage Directive (LVD)
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
    • Customer Support
      • Online Customer Support
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 Features
      • 1.3.1 Block Up Converter (BUC-5003)
      • 1.3.2 Block Down Converter (BDC-5003)
    • 1.4 Summary of Specifications
      • 1.4.1 Physical & Environmental
      • 1.4.2 Prime Power
      • 1.4.3 Monitor & Control
      • 1.4.4 Reference
      • 1.4.5 BUC-5003 Block Up Converter (featured on MBT-5003-XUR)
      • 1.4.6 BDC-5003 Block Down Converter (featured on MBT-5003-XDR)
    • 1.5 Dimensional Envelope
  • Chapter 2. INSTALLATION
    • 2.1 Unpacking and Inspection
    • 2.2 Installation
      • 2.2.1 Standard Rack Mount Installation
      • 2.2.2 Installation Using Optional Bearingless Rack Slide Set
    • 2.3 Connect External Cables
  • Chapter 3. EXTERNAL CONNECTORS
    • 3.1 External Connectors Overview
    • 3.2 MBT-5003 External Connectors
      • 3.2.1 Front Panel Connectors
        • 3.2.1.1 REF OUT Connector, Type ‘BNC’ Female
        • 3.2.1.2 RF OUT Connector (MBT-5003-XUR only), Type ‘N’ Female
        • 3.2.1.3 RF IN Connector (MBT-5003-XDR only), Type ‘N’ Female
      • 3.2.2 Rear Panel Connectors (Typical MBT-5003-XUR / MBT-5003-XDR)
        • 3.2.2.1 J1 | 5/10 MHz EXT REF IN Connector, Type ‘BNC’ Female
        • 3.2.2.2 J2 | IF Connector, Type ‘TNC’ Female
        • 3.2.2.3 J3 | COM Connector (EIA-485 Interface), DB-9F
        • 3.2.2.4 J4 | RELAY (Summary Fault Output) Connector, DB-9F
        • 3.2.2.5 J5 | 10/100 Ethernet (M&C 10/100 BaseT Ethernet) Port, (RJ-45)
        • 3.2.2.6 POWER IN (IEC Line Input AC Power) Connector
        • 3.2.2.7 Ground Connector
  • Chapter 4. FLASH UPGRADING
    • 4.1 Introduction
    • 4.2 Ethernet FTP Upload Procedure
  • Chapter 5. FRONT PANEL OPERATION
    • 5.1 Introduction
      • 5.1.1 Switch Power On
      • 5.1.2 LED Indicators
      • 5.1.3 Keypad
      • 5.1.4 Vacuum Fluorescent Display (VFD)
    • 5.2 Opening Screen
    • 5.3 SELECT: (Main) Menu
      • 5.3.1 SELECT: Config (Configuration)
        • 5.3.1.1 CONFIG: Remote (Remote Control)
        • 5.3.1.2 CONFIG: FltRec (Fault Recovery)
        • 5.3.1.3 CONFIG: ConvA or ConvB (Converter Unit ‘A’ or Converter Unit ‘B’)
        • 5.3.1.4 CONFIG: RefAdj (Reference Oscillator Adjustment)
        • 5.3.1.5 CONFIG: Redun (Redundancy)
      • 5.3.2 SELECT: Monitor
        • 5.3.2.1 MONITOR: Faults
        • 5.3.2.2 MONITOR: Mask
        • 5.3.2.3 MONITOR: Event-Log (Stored Events)
      • 5.3.3 SELECT: Info
        • 5.3.3.1 INFO: Remote (Remote Control)
        • 5.3.3.2 INFO: ConvA or ConvB (Converter Unit ‘A’ or Converter Unit ‘B’)
        • 5.3.3.3 INFO: PSA or PSB (Power Supply ‘A’ or Power Supply ‘B’)
        • 5.3.3.4 INFO: RefOsc (Reference Oscillator)
      • 5.3.4 SELECT: Utility
        • 5.3.4.1 UTILITY: Date/Time (Set Real-time Clock)
        • 5.3.4.2 UTILITY: CID (Circuit ID)
        • 5.3.4.3 UTILITY: Display (VFD Display Brightness)
        • 5.3.4.4 UTILITY: Firmware
      • 5.3.5 SELECT: Test
  • Chapter 6. ETHERNET MANAGEMENT
    • 6.1 Overview
    • 6.2 Ethernet Management Interface Protocols
    • 6.3 SNMP Interface
      • 6.3.1 Management Information Base (MIB) Files
      • 6.3.2 SNMP Community Strings
      • 6.3.3 SNMP Traps
    • 6.4 Telnet Interface
    • 6.5 Web Server (HTTP) Interface
      • 6.5.1 Web Server Page Introduction
      • 6.5.2 Enabling the Web Server Interface
      • 6.5.3 Web Server Interface Access
      • 6.5.4 Web Server Interface “Splash” Page
      • 6.5.5 Web Server Page Descriptions
        • 6.5.5.1 Home Pages
          • 6.5.5.1.1 Home | Home
          • 6.5.5.1.2 Home | Contact
          • 6.5.5.1.3 Home | Support
        • 6.5.5.2 Admin Pages
          • 6.5.5.2.1 Admin | Access
          • 6.5.5.2.2 Admin | SNMP
        • 6.5.5.3 Config Pages
          • 6.5.5.3.1 Config | MBT
          • 6.5.5.3.2 Config | Utility
          • 6.5.5.3.3 Config | Redundancy
        • 6.5.5.4 Status Pages
          • 6.5.5.4.1 Status | Events
          • 6.5.5.4.2 Status | Status
  • Appendix A. REMOTE CONTROL
    • A.1 Introduction
    • A.2 EIA-485
    • A.3 Basic Protocol
    • A.4 Packet Structure
      • A.4.1 Start of Packet
      • A.4.2 Target Address
      • A.4.3 6BAddress Delimiter
      • A.4.4 Instruction Code
      • A.4.5 Instruction Code Qualifier
      • A.4.6 Optional Message Arguments
      • A.4.7 End of Packet
    • A.5 Configure Mute Mode
    • A.6 Remote Commands / Queries
      • A.6.1 MBT-5003 Base Unit Remote Commands and Queries
      • A.6.2 Block Converter (BUC/BDC) Remote Commands and Queries
  • Appendix B. MBT-5003 REDUNDANCY OPERATION
    • B.1 Introduction
    • B.2 Redundant Operation
      • B.2.1 Auto Mode
      • B.2.2 Force Switchover
      • B.2.3 Gain Equalization of Redundant Units
      • B.2.4 Operational Configuration Commands
  • METRIC CONVERSIONS
• BACK COVER