Document Outline

• mn-pcb4000_r2.pdf
  • INSIDE COVER
  • Table of Contents
  • Tables
  • Figures
  • PREFACE
    • About this Manual
      • Reporting Comments or Suggestions Concerning this Manual
    • Conventions and References
      • Patents and Trademarks
      • Warnings, Cautions, and Notes
      • Recommended Standard Designations
      • Metric Conversion
    • Electrical Safety Notice
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
    • Getting Help
      • Contacting Comtech EF Data
      • Returning a Product for Upgrade or Repair
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 Theory of Operation
      • 1.3.1 Phase and Gain Equalization
      • 1.3.2 System Attenuation
      • 1.3.3 Soft Fail Protection
    • 1.4 Dimensional Envelope
  • Chapter 2. EXTERNAL CONNECTORS
    • 2.1 Overview
    • 2.2 Monitor and Control (M&C) Interface Connectors
      • 2.2.1 “SYSTEM COM | J1” Connector
      • 2.2.2 “SSPA COM 1 | J2” / “SSPA COM 2 | J3” Connectors
      • 2.2.3 “SSPA SW OUT | J5” Connector
      • 2.2.4 “RF INPUT SWITCH | J6” Connector
    • 2.3 RF Interface Connectors
      • 2.3.1 “RF IN 1 | J7”, “RF IN 2 | J8” Connectors
      • 2.3.2 “SSPA OUT 1 | J9” Connector
      • 2.3.3 “SSPA OUT 2 | J10” Connector
    • 2.4 Power and Ground Interfaces
      • 2.4.1 AC Power
      • 2.4.2 Ground Connector
  • Chapter 3. INSTALLATION, STARTUP, and TROUBLESHOOTING PROCEDURES
    • 3.1 Overview
    • 3.2 System Assembly, Cabling, and Installation
      • 3.2.1 1+1 Phase Combiner System Assembly
      • 3.2.2 PCCB Cabling Connections
      • 3.2.3 System Component Installation and Interconnection
    • 3.3 Initial System Setup and Verification
      • 3.3.1 LED Status Operation
    • 3.4 Gain or Amplitude Balance Verification and Alignment
    • 3.5 Amplitude Alignment (as necessary)
    • 3.6 Phase Alignment
    • 3.7 System Online and Transmitting
  • Chapter 4. UPDATING FIRMWARE
    • 4.1 Updating Firmware via the Internet
    • 4.2 Getting Started: Preparing for the Firmware Download
    • 4.3 Downloading and Extracting the Firmware Update
    • 4.4 Performing the Automated FTP Upload Procedure
  • Chapter 5. SERIAL REMOTE CONTROL
    • 5.1 Overview
      • 5.1.1 EIA-485
      • 5.1.2 EIA-232
    • 5.2 Remote Commands and Queries Overview
      • 5.2.1 Basic Protocol
      • 5.2.2 Packet Structure
        • 5.2.2.1 Start of Packet
        • 5.2.2.2 Target (Base) Address
        • 5.2.2.3 Virtual Address
        • 5.2.2.4 Address Delimiter
        • 5.2.2.5 Instruction Code
        • 5.2.2.6 Instruction Code Qualifier
        • 5.2.2.7 Optional Message Arguments
        • 5.2.2.8 End Of Packet
    • 5.3 Remote Commands / Queries
  • Appendix A. ASSEMBLY KITS
    • A.1 Overview
      • A.1.1 Summary of Available Assemblies
    • A.2 Common Kit Subassemblies
      • Universal Pole Mounting Kit (PL/12319-1)
      • A.2.2 Unistrut Mounting Kit (KT-0000017)
      • A.2.3 HPOD Mounting Bracket Kit (KT/12300-1)
    • A.3 PCB-4000 1+1 Phase Combiner Box Assemblies
      • A.3.1 PCB-4000 X-Band Unit (PL/11285-1) Assemblies
        • A.3.1.1 X-Band 1:1 Combined Assembly Kit – HPOD (KT/11344-01)
        • A.3.1.2 X-Band 1:1 Waveguide and Switch Redundant Assembly Kit – ODPA (KT/11387-1)
      • A.3.2 PCB-4000 C-Band Unit (PL-0000330) Assemblies
        • A.3.2.1 C-Band 1+1 Phase Combined Top Assembly Kit – HPOD (KT-0000055)
        • A.3.2.2 C-Band 1+1 Phase Combined Waveguide and Switch Kit – HPOD (KT-0000054)
      • A.3.3 PCB-4000 Ku-Band Unit (PL-0021051) Assemblies
        • A.3.3.1 Ku-Band 1+1 Phase Combined System – HPOD (KT-0020621)
        • A.3.3.2 Ku-Band 1+1 Phase Combined Waveguide and Components Kit – HPOD (KT-0020623)
  • METRIC CONVERSIONS
• BACK COVER