Document Outline

• SDM-9000 Rev. 4 Cover
• Errata A
• Errata B
• Errata C
• Table of Contents
  • About this Manual
    • Related Documents
    • Conventions and References
  • European EMC Directive
    • Reporting Comments or Suggestions Concerning this Manual
  • Warranty Policy
    • Limitations of Warranty
    • Exclusive Remedies
    • Disclaimer
• Customer Support
• Overview of Changes to Previous Edition
• Chp 1. INTRODUCTION
  • 1.1 Overview
    • 1.1.1 Nyquist Filter Printed Circuit Boards
    • 1.1.2 Description
    • 1.1.3 Options
  • 1.2 Modem Assemblies
  • 1.3 Modem Specifications
  • 1.4 BER Performance Specifications
    • 1.4.1 Viterbi Decoder BER (QPSK)
    • 1.4.2 Reed˚Solomon Codec BER (QPSK)
    • 1.4.3 8PSK and 16QAM (Viterbi Decoder and Reed˚Solomon Codec)
• Chp 2. INSTALLATION
  • 2.1 Unpacking
  • 2.2 System Options
  • 2.3 System Installation
  • 2.4 External Connectors
    • 2.4.1 TX/IF Output (CP1)
    • 2.4.2 RX/IF Input (CP2)
    • 2.4.3 Receive Data (CP3)
    • 2.4.4 Send Data (CP4)
    • 2.4.5 External Clock (CP5)
    • 2.4.6 Remote (J6)
    • 2.4.7 Fault (J7)
    • 2.4.8 DATA I/O (ESC) Interface (J8)
    • 2.4.9 AUX 1 (J9)
    • 2.4.10 Alarms (J10)
    • 2.4.11 AC Power
    • 2.4.12 DC Power
    • 2.4.13 Ground (GND)
• Chp 3. CONFIGURATION
  • 3.1 Display/M&C
  • 3.2 Modulator
  • 3.3 Demodulator
  • 3.4 Interface
  • 3.5 Nyquist Filter Configuration
    • 3.5.1 Compatibility
    • 3.5.2 Installation
  • 3.6 Software Configuration
    • 3.6.1 Revision Emulation
    • 3.6.2 Remote Interface Specification
    • 3.6.3 Modem Defaults
• Chp 4. OPERATION
  • 4.1 Front Panel
    • 4.1.1 LED Indicators
    • 4.1.2 Front Panel Controls
  • 4.2 Menu System
    • 4.2.1 Configuration
    • 4.2.2 Monitor
    • 4.2.3 Faults/Alarms
    • 4.2.4 Stored Faults/Alarms
    • 4.2.5 Utility
    • 4.3 Clocking Options
      • 4.3.1 G.703 Interface Clocking
      • 4.3.2 ECL/MIL-STD-188 Interface Clocking
• Chp 5. THEORY OF OPERATION
  • 5.1 Display/M&C
    • 5.1.1 Description
    • 5.1.2 Theory of Operation
  • 5.2 Modulator
    • 5.2.1 Description
    • 5.2.2 Specifications
  • 5.3 Demodulator
  • 5.4 Viterbi Decoder
    • 5.4.3 Theory of Operation
  • 5.5 Interface
    • 5.5.1 Description
    • 5.5.2 Digital Interface Specifications
  • 5.6 Backward Alarm Theory and Connections
• Chp 6. MAINTENANCE
  • 6.1 System Checkout
    • 6.1.1 Interface
    • 6.1.2 Modulator
    • 6.1.3 Demodulator
    • 6.1.4 Test Points
  • 6.2 Fault Isolation
    • 6.2.1 Guidelines
    • 6.2.2 System Faults/Alarms
  • 6.3 Module Replacement
  • 6.4 Module Identification
  • 6.5 Repacking for Shipment
• Appendix A. OPTIONS
  • A.1 Reed-Solomon Codec
    • A.1.1 Specifications
    • A.1.3 Installation
  • A.2 Direct Broadcast Satellite
    • A.2.1 Requirements
    • A.2.2 Baseband Physical Interfaces
    • A.2.3 DBS Baseband Interface
    • A.2.4 Baseband Interface Requirements
    • A.2.5 SYNC Decoder (Correlater)
    • A.2.6 SYNC 1 Inversion and Scrambler/Descrambler
    • A.2.7 Reed˚Solomon Coder/Decoder
    • A.2.8 Depth 12 Interleaver/De˚interleaver
    • A.2.9 Inner Coder/Decoder
    • A.2.10 Nyquist Filters
    • A.2.11 DVB with Reed˚Solomon BER (QPSK)
  • A.3 ESC 64 kbit/s Data Option
• Appendix B. REMOTE CONTROL OPERATION
  • B.1 General
  • B.2 Message Structure
    • B.2.1 Start Character
    • B.2.2 Device Address
    • B.2.3 Command/Responses
    • B.2.4 End Character
  • B.3 Configuration Commands/Responses
    • B.3.1 Modulator
    • B.3.2 Demodulator
    • B.3.3 Interface
    • B.3.4 System
  • B.4 Status Commands/Responses
    • B.4.1 Configuration
    • B.4.2 Error Performance
  • B.5 Stored Faults
• Glossary
• Metric Conversions
• Back Cover