Document Outline

• About the printer
  • The outside of the printer
  • The inside of the printer
  • Features and options
• Loading cards
• Loading print ribbon
• Power on the printer
• The LCD panel
• Make a printer test card
• Data formats for the CP60 Card Printer
  • CP Driver data
  • Open Card data format
  • Data formats summary
• Printer Installation
  • Site requirements
    • Operating environment
    • Electrical requirements
    • Physical requirements
• Useful tools
• Network installation
  • Prepare the printer for installation
  • Connect the printer to the network
    • Use the Ethernet port
    • Use the USB port and a wired print server
    • Use the USB port and a wireless print server
  • Set up the network printer
    • Set the Data Format
  • Set up for your card design
    • Set up for CP Driver
    • Set up for the Open Card data format
  • SNMP Support
• Print a card
  • From the CP Driver
  • Using the Open Card data format
• Cleaning the printer
  • Cleaning the printer rollers
• Getting the most out of your printer
• Printer LCD settings
  • LCD menu system
  • View status settings
    • View the Serial Number
    • View the Firmware Revision
    • View Card Counts
    • View the Data Format
    • View the Network Address Mode, IP Addresses, and MAC Address
  • Change settings
    • Set LCD Backlighting
    • Set the Data Format
    • Set the Address Mode
    • Set the IP Address, Subnet Mask, and Gateway Address
    • Set the K Power
• Troubleshooting
• Printer supplies
  • Color print ribbon
  • Monochrome and Topcoat ribbon
  • Monochrome print ribbon
  • Cleaning supplies
• Printer messages
  • DM-00760 Duplex Error
  • The duplex mechanism did not reach the correct position.
  • DM-00762 Duplex Jam
  • The card is stuck in the duplex module.
  • DM-00765 No Duplex
  • The duplex module is not installed or detected.
  • DM-00767 Duplex Jam
  • The card is lost in the duplex module.
  • IS-01206 No Card Picked
  • A card was not picked successfully.
  • SY-01305 Data Error
  • The setting sent to the printer does not match printer features.
  • SY-01306 Data Error
  • The setting value you selected is not valid.
  • SY-01310 Flash Error
  • EEPROM flash data error.
  • SY-01312 Flash error
  • EEPROM flash size error.
  • SY-01314 Flash Error
  • Warning! EEPROM flash write error.
  • SY-01317 Memory Error
  • Memory error.
  • SY-01325 Data Error
  • The options, ribbon, or supply materials installed do not match settings or card data.
  • SY-01327 Data Error
  • The request sent to the printer is not supported.
  • SY-01331 Comm Error
  • Data transmission error.
  • SY-01332 Hardware Error
  • General printer fault.
  • MS-01401, MS-01402, MS-01403 Mag Stripe Data
  • Data sent does not match requirements for track 1.
  • MS-01404, MS-01405, MS-01406 Mag Stripe Error
  • Parity error reading data on track 1, 2 or 3.
  • MS-01407, MS-01408, or MS-01409 Mag Stripe Error
  • LRC error reading data on track 1, 2, or 3.
  • MS-01410, MS-01411, or MS-01412 Mag Stripe Error
  • Start Sentinel error reading data on track 1, 2, or 3.
  • MS-01413, MS-01414, or MS-01415 Mag Stripe Error
  • End Sentinel error reading data on track 1, 2, or 3.
  • MS-01417, MS-01418, MS-01419, MS-01420, MS-01421 Card Jam
  • A card was stuck when attempting to read or write magnetic stripe data on the card.
  • MS-01424 Mag Stripe Error
  • Unable to read any data from the card.
  • MS-01425 Mag Stripe Error
  • Unexpected magnetic stripe coercivity value.
  • MS-01426 EEPROM Error
  • Magnetic stripe module settings EEPROM read or write error.
  • MS-01427 or MS-01428 Mag Stripe Error
  • Configuration information passed through by the printer driver was not accepted by the magnetic stripe module.
  • MS-01429 Mag Stripe Data
  • Data sent to a track does not match the requirements for that track.
  • MS-01430 Mag Stripe Error
  • Control information passed through by the printer driver was not accepted by the magnetic stripe module.
  • MS-01435 No Mag Stripe
  • The magnetic stripe module is not installed or detected.
  • PR-01703 Printhead Error
  • The printhead cam is not in the correct position to print.
  • PR-01705, PR-01706 Card Jam
  • The card is stuck or lost in the printer.
  • PR-01710 EEPROM Error
  • Factory settings read problem.
  • PR-01715, PR-01716 Cover Open
  • The cover was opened during printing.
  • PR-01718 Printhead Temp
  • The printhead temperature is too high.
  • PR-01719 Printhead Error
  • The printhead is not installed or detected.
  • PR-01720 Ribbon Error
  • The print ribbon index mark was not found.
  • PR-01721 EEPROM Error
  • Operational settings read error.
  • PR-01723 Hardware Error
  • General printer fault.
  • PR-01724 Ribbon Break
  • The print ribbon is broken.
  • PR-01726 Ribbon Out
  • Out of print ribbon.
  • PR-01730 Printhead Error
  • Unable to read the printhead temperature.
  • PR-01737 Ribbon Low
  • The print ribbon is low.
  • PR-01738 Ribbon Error
  • The printer cannot identify the ribbon installed.
  • SC-01804 No Smart Card
  • The smart card module is not installed or detected.
• Safety and compliance (FCC)
  • Regulatory compliance
  • Liability statement
  • Safety
  • Acknowledgments