Document Outline

• 130AL-UG.pdf
  • Introduction
    • A Word About Safe Use
    • About This Manual
  • Optional Accessories
  • Using the Davis DriveRight 130AL
    • The Data Screens
    • The Settings Screens
    • The Buttons
    • Entering Settings
      • 1. If necessary, press and hold MODE down to access the settings screens.
      • 2. If necessary, press and release MODE until the set time screen appears.
      • 3. Press "+" or "-" to toggle between the PM, AM, and 24HR segments.
      • 4. When the desired segment appears, press SET/CLEAR.
      • 5. Press "+" or "-" to increment the first digit.
      • 6. When the desired number appears, press SET/CLEAR.
      • 7. Repeat this procedure until all digits have been correctly set.
      • 8. When finished entering the time, press MODE.
  • Calibrating the DriveRight 130AL
    • Calibration Using the Speedometer
      • 1. If necessary, press and hold MODE down to access the settings screens.
      • 2. If necessary, press and release MODE until the Calibration screen appears.
      • 3. Drive the vehicle until you reach 25 MPH (40 km/h) and keep the vehicle steady at that speed.
      • 4. Once the vehicle is moving at the calibration speed, press and hold SET/CLEAR down.
      • 5. Continue to hold SET/CLEAR down until the unit beeps and the word dONE appears on the display.
      • 6. Once the calibration is complete, drive the vehicle and compare the vehicle’s speedometer to t...
      • 7. If necessary, “fine tune” the calibration by pressing "+" or "-".
      • 8. Continue to Press "+" or "-" until the DriveRight agrees with your vehicle’s speedometer at a ...
      • 9. When finished calibrating, press and hold MODE down until you return to the data screen.
    • Calibration Using The Odometer
      • 1. Obtain a rough calibration, using the speedometer as described in “Calibration Using the Speed...
      • 2. After obtaining a rough calibration, reset your vehicle’s trip meter to zero or make a note of...
      • 3. Make a note of the distance travelled reading displayed in the Current Readings screen.
      • 4. Drive your vehicle for at least 20 miles (32 km).
      • 5. When you finish driving, determine how many miles/kilometers the DriveRight recorded by subtra...
      • 6. Compare your vehicle’s trip meter reading to the distance travelled reading on the DriveRight...
      • 7. If necessary, press and hold MODE down to access the settings screens.
      • 8. If necessary, press and release MODE until the calibration screen appears.
      • 9. Press "+" or "-" until the number of Miles or Km shown matches the number of Miles or Km recor...
      • 10. When finished calibrating, press and hold MODE down until you return to the current readings ...
  • Using the Data Screens
    • Current Readings Screen
    • Speed/Distance Log Screen
      • 1. From the speed/distance log screen, press "+" or "-" until the desired day appears.
      • 2. Press and hold down SET/CLEAR until the unit beeps and the code entry screen appears.
      • 3. Use "+" and "-" to enter the correct code.
      • 4. After the code is entered correctly, press MODE.
    • Acceleration/Deceleration Log Screen
    • Driving Time Log Screen
    • Limits Screen
  • Settings Screens
    • Last Correct Code Screen
    • Code Entry Screen
      • 1. From the code entry screen, use "+" and "-" to enter the correct code.
      • 2. When the correct code is entered, press MODE.
      • 1. From the code entry screen, use "+" and "-" to enter your current code.
      • 2. When the correct code is entered, press and hold down SET/ CLEAR.
      • 3. Use "+" and "-" to enter a new code.
      • 4. When the new code is entered, press MODE.
    • Clear All Log Data Screen
      • 1. Press and hold down SET/CLEAR.
      • 2. Continue to hold down SET/CLEAR until the unit beeps.
    • Alarm On/Off Screen
    • Limit Entry Screen
      • 1. Press and release SET/CLEAR until the display segment (MPH or km/h) is flashing.
      • 2. Press "+" to switch from MPH to km/h or vice versa.
      • 3. When the desired unit of measure appears in the display, press SET/CLEAR.
    • Calibration Screen
    • Set Time Screen
      • 1. Press and release SET/CLEAR until the PM, AM, or 24HR segment is flashing.
      • 2. Press "+" to switch between the three possible options: PM, AM, and 24HR or vice versa.
      • 3. When the desired option appears in the display, press SET/ CLEAR.
    • Set Date Screen
      • 1. Press and release SET/CLEAR until the Day.Mo or Mo:Day segment is flashing.
      • 2. Press "+" to switch from Day.Mo to Mo:Day, or vice versa.
      • 3. When the desired format appears in the display, press SET/ CLEAR.
    • Set Year Screen
  • Miscellaneous Information
    • Tamper Protection
    • Battery Operation
    • Display Lamp
    • Restarting the DriveRight 130AL
  • Troubleshooting Guide
  • Technical Specifications
  • Warranty & Repair Information
    • One Year Limited Warranty
    • Questions? Call Davis Customer Service.