Document Outline

• PREFACE
• TABLE OF CONTENTS
• TERMS AND CONDITIONS OF SALE
• RETURNED GOODS POLICY
• IMPORTANT SERVICE INFORMATION
• UNPACKING THE INSTRUMENT
• 1.0 OVERVIEW
  • CONTENTS:
  • 1.1 Safety Precautions, Instructions and Hazards
    • 1.1.1 General information
    • 1.1.2 List of warnings and potential dangers
    • 1.1.3 Reagents
    • 1.1.4 Sample Stream
    • 1.1.5 Waste disposal of the liquid reagents for the colorimetric reaction
    • 1.1.6 Analyzer General Hazards
      • 1.1.6.1 Electrical precautions and hazards
      • 1.1.6.2 Operating precautions and hazards
      • 1.1.6.3 Chemical and waste gas hazards
• 1.0.1 CA-6 Technical Specifications
• 2.0 INTRODUCTION – Analyzer Description
  • 2.1 Applications
  • 2.2 Working principle: Lambert-Beer law
    • 2.2.1 Absorption photometry (Colorimetry):
  • 2.3 Analysis Cycle
    • 2.3.1 Typical Run Sequence:
    • 2.3.3 Programmable Functions
  • 2.4 Components
    • 2.4.1 Fast-loop reservoir
    • 2.4.2 Sampling Pump
    • 2.4.3 3 Way Valve
    • 2.4.4 Micro Peristaltic Pumps
    • 2.4.5 Mixing Pump
    • 2.4.6 Pinch Valve
    • 2.4.7 Colorimetric Reaction Cell
    • 2.4.8 Sample Drain
    • 2.4.9 Electronic Components
• 3.0 OPTIONS
  • 3.1 Dilution Module
  • 3.2 Oxidation/Digestion Module
• 4.0 INSTALLATION
  • 4.1 Unpacking and Inspecting
  • 4.2 Analyzer Handling
  • 4.3 Location and Mounting Instructions
  • 4.4 Pre-Installation
  • 4.5 Electrical Connections
    • 4.5.1 General information
    • 4.5.2 AC Power Connections
    • 4.5.3 Signal Output Connections – TB (4-20 mA, alarm, aux, RS232)
• 5.0 REAGENTS PREPARATION
  • 5.1 Method of Analysis
• 6.0 ANALYZER INITIAL START-UP
  • 6.1 Sample and Drain Tubing Connections
  • 6.2 Powering, Priming and Starting the Analyzer
• 7.0 CALIBRATION
  • 7.1 Blank Calibration (Zero Point)
  • 7.2 Slope Calibration (Factor)
  • 7.3 Step by Step Manual Calibration
• 8.0 USER INTERFACE
  • 8.1 Touch Screen Display
  • 8.2 Passwords (****)
  • 8.3 Main Screen
    • 8.3.1 Status Modes
    • 8.3.2 Menu Buttons
  • 8.4 RUN MENU
    • 8.4.1 START ON-LINE?
    • 8.4.2 CYCLE Ch1 / CYCLE Ch2 / Cycle Extra
    • 8.4.3 EMERGENCY STOP
  • 8.5 DISPLAY MENU
    • 8.5.1 Display Process Values
    • 8.5.2 Chart
    • 8.5.3 Manual Step
  • 8.6 PROGRAM MENU
    • 8.6.1 Analysis Cycle
    • 8.6.2 Extra Cycle
    • 8.6.3 Settings Menu
    • 8.6.2 Calibration Menu
  • 8.7 SERVICE MENU
    • 8.7.1 Method of Operation
  • 8.8 ? HELP MENU
    • 8.8.1 Analyzer Installation
    • 8.8.2 Analyzer Start Up
    • 8.8.3 Start/Stop Commands
    • 8.8.4 Calibrations
    • 8.8.5 Program / Modify Cycles
    • 8.8.6 Functions List
    • 8.8.7 Shut Down Procedure
    • 8.8.8 Maintenance
    • 8.8.9 Troubleshooting
• 9.0 MAINTENANCE
  • 9.0.1 Visual check
  • 9.0.2 Monthly
  • 9.0.4 Annual
  • 9.1 Sample Pump tubing replacement
  • 9.2 Micro Peristaltic Tubing Replacement
  • 9.3 Accessories and Spare Parts
• 10.0 ANALYZER SHUT DOWN
• 11.0 REAGENT RECIPE and PROGRAM SEQUENCE
  • METHOD DESCRIPTION
  • FIRST START-UP PROCEDURE
  • 11.1 Analysis Cycle
  • 11.2 Extra Cycle
  • 11.3 TEST DATA
  • 11.4 Reagents
    • 11.4.1 REAGENT 1
    • 11.4.2 REAGENT 2
    • 11.4.3 Standard Solution