Document Outline

• Essential Instructions
• Section i Introduction
  • Preface
  • Definitions
  • Symbols
  • What You Need To Know
  • Can You Use the Quick Start Guide?
  • Quick Start Guide for Oxymitter 4000 Systems
  • Quick Reference Guide Manual Calibration Instructions
  • HART Communicator Fast Key Sequences
• Section 1 Description and Specifications
  • Component Checklist
  • System Overview
    • Scope
    • System Description
    • System Configuration
    • System Features
    • Handling the Oxymitter 4000
    • System Considerations
  • IMPS 4000 (Optional)
  • SPS 4001B (Optional)
    • Mounting
    • Operation
  • Model 751 Remote Powered Loop LCD Display
  • Probe Options
    • Diffusion Elements
  • Specifications
• Section 2 Installation
  • Mechanical Installation
    • Selecting Location
    • Probe Installation
    • Remote Electronics Installation
  • Electrical Installation (with Integral Electronics)
  • Electrical Installation (with Remote Electronics)
    • Install Interconnecting Cable
  • Pneumatic Installation
  • IMPS 4000 Connections
  • SPS 4001B Connections
• Section 3 Configuration of Oxymitter 4000 with Membrane Keypad
  • Verify Installation
    • Mechanical Installation
    • Terminal Block Wiring
    • Oxymitter 4000 Configuration
  • Logic I/O
    • Recommended Configuration
• Section 4 Configuration of Oxymitter 4000 with LOI
  • Verify installation
    • Mechanical Installation
    • Terminal Block Wiring
    • Oxymitter 4000 Configuration
  • Logic I/O
    • Recommended Configuration
• Section 5 Startup and Operation of Oxymitter 4000 with Membrane Keypad
  • Power Up
  • Operation
    • Overview
• Section 6 Startup and Operation of Oxymitter 4000 with LOI
  • Power Up
  • Start Up Oxymitter 4000 Calibration
  • Navigating the Local Operator Interface
    • Overview
    • Lockout
  • LOI Key Designations
  • LOI Menu Tree
  • Oxymitter 4000 Setup at the LOI
  • LOI Installation
  • Oxymitter 4000 Test Points
  • Remote Powered Loop LCD Display (Optional)
• Section 7 HART/AMS
  • Overview
  • HART Communicator Signal Line Connections
  • HART Communicator PC Connections
  • Off-Line and On-Line Operations
  • Logic I/O Configurations
  • HART/AMS Menu Tree
  • HART Communicator O2 Cal Method
  • Defining a Timed Calibration via HART
  • D/A Trim Procedure
• Section 8 Troubleshooting
  • Overview
  • General
  • Alarm Indications
  • Alarm Contacts
  • Identifying and Correcting Alarm Indications
  • Calibration Passes, but Still Reads Incorrectly
• Section 9 Maintenance and Service
  • Overview
  • Calibration with Keypad
    • Automatic Calibration
    • Semi-Automatic Calibration
    • Manual Calibration with Membrane Keypad
  • Calibration with LOI
  • Oxymitter 4000 Repair
    • Removal and Replacement of Probe
• Section 10 Replacement Parts
  • Probe Replacement Parts
  • Electronics Replacement Parts
• Section 11 Optional Accessories
  • HART Handheld 375 Communicator
  • Asset Management Solutions (AMS)
  • By-Pass Packages
  • IMPS 4000 Intelligent Multiprobe Test Gas Sequencer
  • SPS 4001B Single Probe Autocalibration Sequencer
  • O2 Calibration Gas
  • Catalyst Regeneration
  • OxyBalance Display and Averaging System
• Appendix A Safety Data
  • Safety Instructions
  • Safety Data Sheet for Ceramic Fiber Products
• Appendix B Return of Material
  • Returning Material